0774652 RING-RETAINING Caterpillar parts
69D, 769D, 771D, 793D, 834G, 834H, 836G, 836H, AD30, R1700G
Rating:
Alternative (cross code) number:
CA0774652
077-4652
0774652
CA0774652
077-4652
0774652
Weight: 0.01 pounds 0 kg.
LANDFILL COMPACTOR, WHEEL DOZER,
Compatible equipment models: 0774652:
Number on catalog scheme:
19
For full view, you need register
Information:
207-1511 Electric Starting Motor Gp
Illustration 1 g01139250
Illustration 2 g01139249
When the electric starting motor is viewed from the drive end, the motor rotates in the following direction. ... ClockwiseNo load conditions at 25 °C (77 °F) Speed ... 3638 413 RPM Current ... 90 16 ampere Voltage ... 23 V (1) Tighten the nut on the battery terminal to the following torque. ... 30.5 3.5 N m (22 3 lb ft) (2) Tighten the nut on the ground terminal to the following torque. ... 30.5 3.5 N m (22 3 lb ft) (3) Tighten the nut on the switch terminal to the following torque. ... 2.25 0.25 N m (20 2 lb in)Note: The switch terminal must be insulated with heat shrink tubing. Do not use molded terminals. (4) Tighten the nut on the motor terminal to the following torque. ... 14.7 3.4 N m (11 3 lb ft)Note: The internal Torx screw must be held during tightening or loosening of the nut. (5) Tighten the nut on the motor frame terminal to the following torque. ... 8 3 N m (70 27 lb in)Solenoid
Current draw at 20 V and 25 °C (77 °F) Pull-in windings ... 36 amp Hold-in windings ... 6 ampMounting Position
Illustration 3 g00726327
(A) The electric starting motor must be engine mounted with the start solenoid: ... 15° minimum above horizontal (B) Allowable range 207-1517 Electric Starting Motor Gp
Illustration 4 g01139254
Typical example
Illustration 5 g01139255
Typical solenoid connectionsWhen the electric starting motor is viewed from the drive end, the motor rotates in the following direction. ... ClockwiseNo load conditions at 25 °C (77 °F) Speed ... 7200 1250 RPM Current ... 82.5 17.5 amp Voltage ... 23 V (1) Tighten the nut on the battery terminal to the following torque. ... 30.5 3.5 N m (22 3 lb ft) (2) Tighten the nut on the ground terminal to the following torque. ... 30.5 3.5 N m (22 3 lb ft) (3) Tighten the nut to the following torque. ... 2.25 0.25 N m (20 2 lb in) (4) Tighten the nut on the switch terminal to the following torque. ... 2.25 0.25 N m (20 2 lb in) (5) Tighten the nut on the motor terminal to the following torque. ... 14.7 3.4 N m (11 3 lb ft)Note: The internal Torx screw must be held during tightening or loosening of the motor terminal nut. (6) Tighten the nut on the motor frame terminal to the following torque. ... 8 3 N m (70 27 lb in)Solenoid
Current draw at 20 V and 25 °C (77 °F) Pull-in windings ... 57 amp at 20 V Hold-in windings ... 13 amp at 20 VMounting Position
Illustration 6 g00726327
(A) The electric starting motor must be engine mounted with the start solenoid: ... 15° minimum above horizontal (B) Allowable range
Illustration 1 g01139250
Illustration 2 g01139249
When the electric starting motor is viewed from the drive end, the motor rotates in the following direction. ... ClockwiseNo load conditions at 25 °C (77 °F) Speed ... 3638 413 RPM Current ... 90 16 ampere Voltage ... 23 V (1) Tighten the nut on the battery terminal to the following torque. ... 30.5 3.5 N m (22 3 lb ft) (2) Tighten the nut on the ground terminal to the following torque. ... 30.5 3.5 N m (22 3 lb ft) (3) Tighten the nut on the switch terminal to the following torque. ... 2.25 0.25 N m (20 2 lb in)Note: The switch terminal must be insulated with heat shrink tubing. Do not use molded terminals. (4) Tighten the nut on the motor terminal to the following torque. ... 14.7 3.4 N m (11 3 lb ft)Note: The internal Torx screw must be held during tightening or loosening of the nut. (5) Tighten the nut on the motor frame terminal to the following torque. ... 8 3 N m (70 27 lb in)Solenoid
Current draw at 20 V and 25 °C (77 °F) Pull-in windings ... 36 amp Hold-in windings ... 6 ampMounting Position
Illustration 3 g00726327
(A) The electric starting motor must be engine mounted with the start solenoid: ... 15° minimum above horizontal (B) Allowable range 207-1517 Electric Starting Motor Gp
Illustration 4 g01139254
Typical example
Illustration 5 g01139255
Typical solenoid connectionsWhen the electric starting motor is viewed from the drive end, the motor rotates in the following direction. ... ClockwiseNo load conditions at 25 °C (77 °F) Speed ... 7200 1250 RPM Current ... 82.5 17.5 amp Voltage ... 23 V (1) Tighten the nut on the battery terminal to the following torque. ... 30.5 3.5 N m (22 3 lb ft) (2) Tighten the nut on the ground terminal to the following torque. ... 30.5 3.5 N m (22 3 lb ft) (3) Tighten the nut to the following torque. ... 2.25 0.25 N m (20 2 lb in) (4) Tighten the nut on the switch terminal to the following torque. ... 2.25 0.25 N m (20 2 lb in) (5) Tighten the nut on the motor terminal to the following torque. ... 14.7 3.4 N m (11 3 lb ft)Note: The internal Torx screw must be held during tightening or loosening of the motor terminal nut. (6) Tighten the nut on the motor frame terminal to the following torque. ... 8 3 N m (70 27 lb in)Solenoid
Current draw at 20 V and 25 °C (77 °F) Pull-in windings ... 57 amp at 20 V Hold-in windings ... 13 amp at 20 VMounting Position
Illustration 6 g00726327
(A) The electric starting motor must be engine mounted with the start solenoid: ... 15° minimum above horizontal (B) Allowable range
Caterpillar parts catalog:
Parts ring Caterpillar catalog:
69D, 768C, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772B, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, AD40, AD45, AD45B...
769C, 769D, 771C, 771D, D9R, D9T
69D, 769C, 769D, 771C, 771D
69D, 768C, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM, AD55, AD55B, AD60, R2900G, R3000H
69D, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM
69D, 769C, 769D, 770G, 770G OEM, 771C, 771D, 772G, 772G OEM, 795F AC, 795F XQ, 797F
769C, 769D, 770G, 770G OEM, 771C, 771D, 772G, 772G OEM
69D, 769C, 769D, 771C, 771D, 773
735, 735B, 740, 740B, AD30, D350E II, D400E II
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, D10, D10N, D10R, D11N, D11R, D11T
322 LN, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D FM LL, 325 LN, 325B L, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 3...
322B L, 322C FM, 325B L, 330, 330 FM L, 330 L, 330B L, 330C, 330C FM, 330C MH, 330D FM, 345B, 345B II, 345B II MH, 345B L, 345C, 350, 350 L, 568 FM LL, 834G, 834H, M325B, M330D, W330B, W345B II
730, 730C, 735, 735B, 740, 740B, D300E II, D350E II, D400E II
725, 730, D250E II, D300E II
1577371
RING-CLAMP
D250E II, D300E II
D250E II, D300E II
1390, 2590, 322B L, 325B L, 325C, 325C FM, 325C L, 325D FM, 325D FM LL, 325D MH, 330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345C, 345C L, 345C MH, 541, 541 2, 551, 552, 552 2, 568 FM LL, 725...
D250E II
1749593
RING-SEAL
D250E II, D300E II, D400E II
D250E II, D300E II, D400E II
725C, 730C, 735, 735B, 740, 740B, D350E II, D400E II
735, 735B, 740, 740B, AD30, D350E II, D400E II
735, 735B, 740, 740B, D350E II, D400E II
1096494
RING-RETAINING
1190, 1190T, 1390, 2390, 2391, 2590, 325D FM, 325D FM LL, 330B L, 330C FM, 330C L, 330D FM, 330D L, 521, 521B, 522, 522B, 5230, 5230B, 541, 541 2, 568 FM LL, D350E II, D400E II, MP318, TK1051, TK721, ...
1190, 1190T, 1390, 2390, 2391, 2590, 325D FM, 325D FM LL, 330B L, 330C FM, 330C L, 330D FM, 330D L, 521, 521B, 522, 522B, 5230, 5230B, 541, 541 2, 568 FM LL, D350E II, D400E II, MP318, TK1051, TK721, ...
1440638
RING-ADAPTER
D350E II, D400E II
D350E II, D400E II
5U1037
RING-ADAPTER
D350E II, D35HP, D400
D350E II, D35HP, D400