1057342 RING Caterpillar parts
307B, 307C, 308C, 311B, 312B, 312B L, 312C, 312C L, 313B, 315, 315B L, 315C, 315D L, 317, 317B LN
Rating:
Alternative (cross code) number:
CA1057342
105-7342
1057342
CA1057342
105-7342
1057342
Weight: 0.03 pounds 0 kg.
EXCAVATOR, MINI HYD EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$310.03
27 Apr 2021
21.0[9.45] Pounds
US: Pit_Stop_Auto
New A/C Compressor and Component Kit 1057342 - Tacoma
Pit Stop Auto Group HVAC --> A/C Clutch and Compressor || A kit containing an A/C compressor and additional components for installation || KIT: COMPRESSORS: 1011416; KIT: CONDENSERS: 11610 || Compressor-Condenser Replacement Kit || A/C Compressor and Component Kit
Pit Stop Auto Group HVAC --> A/C Clutch and Compressor || A kit containing an A/C compressor and additional components for installation || KIT: COMPRESSORS: 1011416; KIT: CONDENSERS: 11610 || Compressor-Condenser Replacement Kit || A/C Compressor and Component Kit
Number on catalog scheme:
8
For full view, you need register
Compatible equipment models: 1057342:
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
D 8T-3034 Water Pump Seal Driver 1
F 4C-5592 Anti-Seize Compound -
G 1P-0520 Driver Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Prior to assembly, check the taper on the auxiliary water pump shaft and the impeller. Refer to Special Instruction, REHS2688, "Installation of the 264-8897 Auxiliary Sea Water Pump Gp".
Illustration 1 g01206943
Illustration 2 g01206899
Use Tooling (A) to install bearings (12) in housing (3). Install the bearing joints at a 5 degree angle from the horizontal centerline of housing (3). Use Tooling (G) to install bearings (13) in housing (3). Install the bearing joints at a 15 degree angle from the vertical centerline of housing (3). Refer to Specifications, "Auxiliary Water Pump - Sea Water".
Place shaft (17) into housing (3).
Install thrust washer (18) and bolts (19).
Lubricate the bore of seal (11) with glycerin or equivalent. Place seal (11) into housing (3).
Install O-ring seal (10).
Connect housing (3) and housing (2). Align the marks and the bolt holes of the housings.
Lubricate seal group (9) with clean water. Place seal group (9) into housing (2). Ensure that the identification mark is oriented away from the seal group that is mounted on the shaft.
Use Tooling (D) in order to push seal group (9) on shaft (17) until the seal face makes light contact.
Install the spring on seal group (9). Note: If impeller (8) has been balanced in the field, impeller (8) cannot be used.
Place impeller (8) on shaft (17).
Use the following procedure for pumps that use the 388-7069 Bolt or newer and 378-8520 Spacer or newer.
Apply Tooling (F) to the threads of bolt (14).
Apply Tooling (F) to both sides of washer (15).
Install washer (15) and bolt (14). Tighten bolt (14) to a torque of 200 N m (150 lb ft) in order to seat impeller (8) on shaft (17).
Loosen bolt (14) until washer (15) is loose.
Tighten bolt (14) to a torque of 50 N m (37 lb ft). Turn bolt (14) for an additional 90 degrees (1/4 turn).
Use the following procedure for all other auxiliary water pumps.
Apply Tooling (F) to the threads of bolt (14).
Apply Tooling (F) to both sides of washer (15).
Install washer (15) and bolt (14). Tighten bolt (14) to a torque of 370 50 N m (275 37 lb ft).
Install O-ring seal (16).
Position housings (2) and (3) on housing (1). Align the marks and the bolt holes of the housings.
Install bolts (4).
Install O-ring seal (5). Install gear (6) and bolts (7).
Ensure that the auxiliary water pump shaft rotates freely when the shaft is turned by hand. End By:
Install the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
D 8T-3034 Water Pump Seal Driver 1
F 4C-5592 Anti-Seize Compound -
G 1P-0520 Driver Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Prior to assembly, check the taper on the auxiliary water pump shaft and the impeller. Refer to Special Instruction, REHS2688, "Installation of the 264-8897 Auxiliary Sea Water Pump Gp".
Illustration 1 g01206943
Illustration 2 g01206899
Use Tooling (A) to install bearings (12) in housing (3). Install the bearing joints at a 5 degree angle from the horizontal centerline of housing (3). Use Tooling (G) to install bearings (13) in housing (3). Install the bearing joints at a 15 degree angle from the vertical centerline of housing (3). Refer to Specifications, "Auxiliary Water Pump - Sea Water".
Place shaft (17) into housing (3).
Install thrust washer (18) and bolts (19).
Lubricate the bore of seal (11) with glycerin or equivalent. Place seal (11) into housing (3).
Install O-ring seal (10).
Connect housing (3) and housing (2). Align the marks and the bolt holes of the housings.
Lubricate seal group (9) with clean water. Place seal group (9) into housing (2). Ensure that the identification mark is oriented away from the seal group that is mounted on the shaft.
Use Tooling (D) in order to push seal group (9) on shaft (17) until the seal face makes light contact.
Install the spring on seal group (9). Note: If impeller (8) has been balanced in the field, impeller (8) cannot be used.
Place impeller (8) on shaft (17).
Use the following procedure for pumps that use the 388-7069 Bolt or newer and 378-8520 Spacer or newer.
Apply Tooling (F) to the threads of bolt (14).
Apply Tooling (F) to both sides of washer (15).
Install washer (15) and bolt (14). Tighten bolt (14) to a torque of 200 N m (150 lb ft) in order to seat impeller (8) on shaft (17).
Loosen bolt (14) until washer (15) is loose.
Tighten bolt (14) to a torque of 50 N m (37 lb ft). Turn bolt (14) for an additional 90 degrees (1/4 turn).
Use the following procedure for all other auxiliary water pumps.
Apply Tooling (F) to the threads of bolt (14).
Apply Tooling (F) to both sides of washer (15).
Install washer (15) and bolt (14). Tighten bolt (14) to a torque of 370 50 N m (275 37 lb ft).
Install O-ring seal (16).
Position housings (2) and (3) on housing (1). Align the marks and the bolt holes of the housings.
Install bolts (4).
Install O-ring seal (5). Install gear (6) and bolts (7).
Ensure that the auxiliary water pump shaft rotates freely when the shaft is turned by hand. End By:
Install the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Install".
Caterpillar parts catalog:
Parts ring Caterpillar catalog:
311B, 312E, 312E L, 316E L, 318E L, 320E, 320E L, 320E LN, 323E L, 324E, 324E L, 324E LN, 325B, 329E, 329E L, 329E LN, 350, 365B, 365B L, 375, 385B, 901C, 902C, 903C, 904B, 904H, D3K XL, D4K XL, D5K L...
1090, 1190, 1190T, 1290T, 1390, 24H, 312C, 312D, 315C, 315D L, 318C, 319C, 319D, 320 L, 320B, 320C, 320C L, 320D, 320E L, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 324D, 324D FM, 324D FM LL, 32...
312C, 312D, 315C, 315D L, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D...
308D, 311B, 311C
308C, 311, 311B, 311C, 311D LRR, 312D, 312D L, 312E, 312E L, 313D, 314D CR, 314D LCR, 314E CR, 314E LCR, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 324D, 324D L, 324E, 324E L, 324E LN, 329D,...
1090, 1190, 1190T, 1290T, 1390, 2290, 2384C, 2390, 2391, 2491, 2590, 315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, ...
315, 315B, 315C, 933, 933C, D3C III, D4C III, D5C III
315D L, 318E L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D2 ...
315, 315B, 933, 933C, 939, 939C, D3C III, D4C III, D5C III
315, 315B, 933, 933C, 939, 939C, D3C III, D4C III, D5C III
311, 311B, 312B, 320 L, 320B
311, 311B, 312B, 320 L, 320B
315, 317, 320 L, 325, 325 LN
1076932
RING
315, 317
315, 317
1057395
RING
315, 317
315, 317
315, 317
308C, 308D, 311, 311B, 311C, 311D LRR, 312D, 312D L, 312E, 312E L, 313D, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 315B L, 315C, 315D L, 317, 317B LN, 318B, 320D, 320D L, 320D2, 320D2 L, 320E, ...
307, 307B, 311B, 312B, 312B L, 315, 315B L, 317, 317B LN
0950916
RING-RETAINING
561N, D5N, D5R LGP, D6N, E300B, M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318, M318C, M318C MH, M318D, M318D MH, M320, M322C, M322D, M322D MH, M325C MH, M325D L MH, M325...
561N, D5N, D5R LGP, D6N, E300B, M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318, M318C, M318C MH, M318D, M318D MH, M320, M322C, M322D, M322D MH, M325C MH, M325D L MH, M325...
0951779
RING-BACKUP
303.5, 304, 304.5, 305, 305.5, 305.5E, 306, 306E, 312, 315, 317, E70B
303.5, 304, 304.5, 305, 305.5, 305.5E, 306, 306E, 312, 315, 317, E70B
1057377
RING
314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 317
314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 317
311D LRR, 312B L, 312C, 312D, 312E, 314D LCR, 314E LCR, 315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D...
315, 317
315, 315B, 315B L, 315C, 317, 317B LN, 318B, 318C, 319C, 320 L, 320B, 320C, M316C, M316D, M318, M320, M322C, M322D, M322D MH, M325C MH, M325D MH