1156880 RING-BACKUP Caterpillar parts
420F, 424B, 428F, 430F, 432F, 434F, 444F, M312, M315, M318, M320
Rating:
Alternative (cross code) number:
CA1156880
115-6880
1156880
CA1156880
115-6880
1156880
Weight: 0.01 pounds 0 kg.
Information:
AXIAL WIDTH
.6
mm
ID
11
mm
MATERIAL
(PTFE) Plastic
OD
13
mm
RADIAL HEIGHT
1
mm
BACKHOE LOADER, WHEELED EXCAVATOR,
Compatible equipment models: 1156880:
Information:
Installation Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     9U-7257     Cradle     1    
B     9U-7256     Guide     1    
C     9U-7225     Camshaft Pilot     2    
D     9U-7240     Camshaft Hook     2    
H     9U-7243     Alignment Sleeve     1    
J     9S-3263     Thread Lock Compound     1    
K     8T-2998     Lubricant     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the camshaft and camshaft bearings are thoroughly clean. Lubricate the camshaft lobes with a 50/50 mixture of Tooling (K) and clean engine oil. Apply a thin coat of clean engine oil on the camshaft bearings.
Illustration 1 g00509797
Illustration 2 g00581441
Install Tooling (A) on the cylinder head at Location (Y) .
Illustration 3 g01024862
Install Tooling (B) on front housing (7) . Do not tighten the bolts that hold Tooling (B) to front housing (7) at this time.
Use Tooling (H) to align Tooling (B) with the camshaft bearings. Tighten the bolts that hold Tooling (B) to front housing (7) . Remove Tooling (H) .Note: Tooling (H) should move freely from the bore of Tooling (B) .
Illustration 4 g00581445
Install Tooling (C) in the end of camshaft (8) .Note: Rotate the camshaft during installation. This will prevent the camshaft from binding in the camshaft bearings.
Use a suitable lifting device in order to position camshaft (8) into Tooling (B) and the cylinder head. The weight of the camshaft is approximately 39 kg (86 lb).
Illustration 5 g00581444
Illustration 6 g00581443
Note: Tooling (C) must be removed before the camshaft can be completely installed in the cylinder head.
Remove the lifting device. Rotate the camshaft during installation. Use care not to allow the end of the camshaft and Tooling (C) to drop. Use Tooling (D) to assist in aligning camshaft (8) with the camshaft bearings.
Remove Tooling (C) and finish installing camshaft (8) in the bore.
Remove Tooling (A) and Tooling (B) .
Illustration 7 g00576240
Illustration 8 g00576839
Install O-ring seals (5) and (6) in seal assembly (3) . Lubricate seal (6) with Tooling (K) .
Install seal assembly (3) . Position adapter (4) . Ensure that the dowel in adapter (4) engages the hole in the camshaft.
Position thrust plate (1) . Apply Tooling (J) to bolts (2) . Hold thrust plate (1) in position and install bolts (2) . Evenly tighten bolts (2) until seal assembly (3) and O-ring seal (5) are seated against the cylinder head.Note: Be careful in order to ensure that O-ring seal (5) stays in the groove in seal assembly (3) .End By:
Install the rocker arms and the rocker shafts. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Install".
Install the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install".
Alternative Installation Procedure
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
E (1)     177-8001     Sleeve     1    
F     177-8002     Adapter     1    
G
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     9U-7257     Cradle     1    
B     9U-7256     Guide     1    
C     9U-7225     Camshaft Pilot     2    
D     9U-7240     Camshaft Hook     2    
H     9U-7243     Alignment Sleeve     1    
J     9S-3263     Thread Lock Compound     1    
K     8T-2998     Lubricant     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the camshaft and camshaft bearings are thoroughly clean. Lubricate the camshaft lobes with a 50/50 mixture of Tooling (K) and clean engine oil. Apply a thin coat of clean engine oil on the camshaft bearings.
Illustration 1 g00509797
Illustration 2 g00581441
Install Tooling (A) on the cylinder head at Location (Y) .
Illustration 3 g01024862
Install Tooling (B) on front housing (7) . Do not tighten the bolts that hold Tooling (B) to front housing (7) at this time.
Use Tooling (H) to align Tooling (B) with the camshaft bearings. Tighten the bolts that hold Tooling (B) to front housing (7) . Remove Tooling (H) .Note: Tooling (H) should move freely from the bore of Tooling (B) .
Illustration 4 g00581445
Install Tooling (C) in the end of camshaft (8) .Note: Rotate the camshaft during installation. This will prevent the camshaft from binding in the camshaft bearings.
Use a suitable lifting device in order to position camshaft (8) into Tooling (B) and the cylinder head. The weight of the camshaft is approximately 39 kg (86 lb).
Illustration 5 g00581444
Illustration 6 g00581443
Note: Tooling (C) must be removed before the camshaft can be completely installed in the cylinder head.
Remove the lifting device. Rotate the camshaft during installation. Use care not to allow the end of the camshaft and Tooling (C) to drop. Use Tooling (D) to assist in aligning camshaft (8) with the camshaft bearings.
Remove Tooling (C) and finish installing camshaft (8) in the bore.
Remove Tooling (A) and Tooling (B) .
Illustration 7 g00576240
Illustration 8 g00576839
Install O-ring seals (5) and (6) in seal assembly (3) . Lubricate seal (6) with Tooling (K) .
Install seal assembly (3) . Position adapter (4) . Ensure that the dowel in adapter (4) engages the hole in the camshaft.
Position thrust plate (1) . Apply Tooling (J) to bolts (2) . Hold thrust plate (1) in position and install bolts (2) . Evenly tighten bolts (2) until seal assembly (3) and O-ring seal (5) are seated against the cylinder head.Note: Be careful in order to ensure that O-ring seal (5) stays in the groove in seal assembly (3) .End By:
Install the rocker arms and the rocker shafts. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Install".
Install the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install".
Alternative Installation Procedure
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
E (1)     177-8001     Sleeve     1    
F     177-8002     Adapter     1    
G
Cat SIS web machinery list:
Parts ring Caterpillar catalog:
1505884
RING
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320B, 320C, 322B LN, 322C, 322C FM, 324D, 324D FM, 32...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320B, 320C, 322B LN, 322C, 322C FM, 324D, 324D FM, 32...
6I6784
RING-SEAL
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 321D LCR, 323D L, 323D LN, 323D SA, 325, 325 L, 325 LN, 325B L, 325C, 325D L, ...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 321D LCR, 323D L, 323D LN, 323D SA, 325, 325 L, 325 LN, 325B L, 325C, 325D L, ...
7Y4628
RING
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320E LN, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 32...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320E LN, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 32...
0960433
RING-RETAINING
312C, 312D, 315C, 315D L, 318C, 319C, 319D, 319D LN, 320B, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B...
312C, 312D, 315C, 315D L, 318C, 319C, 319D, 319D LN, 320B, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B...
1799771
RING
314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 320B, 320C, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 345B II, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L,...
314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 320B, 320C, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 345B II, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L,...
9T3745
RING
1090, 1190, 1190T, 1290T, 1390, 215B, 225, 2290, 231D, 2390, 2391, 2491, 2590, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D FM LL, 325, 325 L, 325 LN, 325B, 325B L, 325C FM, 325D FM, 325...
1090, 1190, 1190T, 1290T, 1390, 215B, 225, 2290, 231D, 2390, 2391, 2491, 2590, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D FM LL, 325, 325 L, 325 LN, 325B, 325B L, 325C FM, 325D FM, 325...
1589065
RING
1390, 2590, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D L, 329D L, 329D LN, 329E, 33...
1390, 2590, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D L, 329D L, 329D LN, 329E, 33...
1799667
RING
1390, 2590, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D L, 329D L, 329D LN, 329E, 33...
1390, 2590, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D L, 329D L, 329D LN, 329E, 33...
0962665
RING-BACKUP
1390, 2590, 320 L, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E LN, 325 LN, 3...
1390, 2590, 320 L, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E LN, 325 LN, 3...
1057262
RING-WEAR
322 LN, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D FM LL, 325B L, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 350, 350 ...
322 LN, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D FM LL, 325B L, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 350, 350 ...
7Y4945
RING-BACKUP
322 LN, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D LN, 324E LN, 325 LN, 325B L, 325C, 325D, 325D L, 328D LCR, 329D LN, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 3...
322 LN, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D LN, 324E LN, 325 LN, 325B L, 325C, 325D, 325D L, 328D LCR, 329D LN, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 3...
0965609
RING
322 LN, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D FM LL, 325 LN, 325B L, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 3...
322 LN, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D FM LL, 325 LN, 325B L, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 3...
4431065
RING-SNAP
424B
424B
4431064
RING-WEAR
424B, 424B HD
424B, 424B HD
3979176
RING-CUSHION
424B, 424B HD
424B, 424B HD
3428001
RING
424B
424B
3427999
RING
424B, 424B HD
424B, 424B HD
2406377
RING
424B
424B
4368718
RING-WEAR
434F, 444F
434F, 444F
4348908
RING-WIPER
434F, 444F
434F, 444F
3475951
RING
416F, 420F, 428F, 430F, 432F
416F, 420F, 428F, 430F, 432F
3895175
RING AS-PISTON
272D, 272D XHP, 299D, 299D XHP, 910K, 914K
272D, 272D XHP, 299D, 299D XHP, 910K, 914K
3895174
RING AS-PISTON
272D, 272D XHP, 299D, 299D XHP, 910K, 914K
272D, 272D XHP, 299D, 299D XHP, 910K, 914K
1250965
RING-RETAINING
416F, 420F, 422F, 430F, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 938H, 980G, 980G II, 980H, 980K, 980K HLG, 980M,...
416F, 420F, 422F, 430F, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 938H, 980G, 980G II, 980H, 980K, 980K HLG, 980M,...