AVSPARE.COM
parts catalog

RING-SEAL 1400246 - Caterpillar



1400246 RING-SEAL Caterpillar parts RING
Rating:
26
Alternative (cross code) number:
CA1400246
140-0246
1400246
Caterpillar 1400246 RING-SEAL
Weight: 0.09 pounds 0 kg.

Buy RING-SEAL 1400246 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

3. Make sure the seven O-ring seals are in position on the back side of the relief control valve. Put relief control valve (2) in position on the transmission.4. Connect three oil lines (1) to the relief control valve.Disassemble Relief Control Valve
START BY:a) remove relief control valve 1. Remove cover (1) and the O-ring seal behind the cover only if a replacement is necessary.
Cover (2) holds three springs under compression. Support cover (2) when the bolts are removed to prevent personal injury.
2. Remove cover (2) and O-ring seals (3) from the valve body. 3. Remove valve assembly (4) and O-ring seal (5).
Retainer (9) holds spring (8) under compression. Support retainer (9) when spiral snap ring (10) is removed to prevent personal injury.
4. Remove spiral snap ring (10), retainer (9), spring (8), poppet (7) and shims (11) from valve (6). 5. Remove cover (12) and the O-ring seal behind the cover. 6. Remove three springs (13), (14) and (15) from the valve body. 7. Remove two covers (16) from the valve body. 8. Remove two plugs (17) from the valve body. Remove the two O-ring seals from the plugs.9. Remove two pins (18) that hold valve assemblies (19) in the valve body. Remove valve assemblies (19).10. Remove two O-ring seals (20) from the valve body.
Pin (22) holds spring (23) in compression. Use the following procedure to prevent personal injury.
11. Install tool (A) in the collar as shown. 12. Put the valve assembly in a vise as shown. Tighten the vise to release the pressure on pin (21). Use a hammer and a punch to remove pin (22) from the valve assembly and pin (21). Slowly open the vise to release the compression of spring (23). 13. Remove pin (21), retainer (24), spring (23), valve (25) and pin (22) from collar (26).14. Repeat Steps 11 through 13 for the other valve assembly.Assemble Relief Control Valve
1. Put valve (1) in position against collar (5). The side of the collar with the chamfer must be against the side of the valve with the chamfer. Put pin (4) in position through retainer (3). Put retainer (3) and spring (2) against valve (1). 2. Install tool (A) in collar (5). Put the valve assembly in a vise as shown. Use the vise to put spring (2) in compression. Tighten the vise until the hole in pin (4) is in alignment with the small hole in collar (5). Install pin (6) through collar (5) and pin (4). Pin (6) must not extend beyond the outer surface of collar (5).3. Remove the valve assembly from the vise. Remove tooling (A). Repeat Steps 1 through 3 for the other valve assembly. 4. Install the two valve assemblies (10) in the valve body with the large hole (9) in the collar up as shown. Install pins (8) in the valve body so that the end of the pin goes through hole (9). Install the O-ring seals on plugs (7) and install the plugs in the valve body.


Parts ring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.