1505884 RING Caterpillar parts
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320B, 320C, 322B LN, 322C, 322C FM, 324D, 324D FM, 32...
Rating:
Alternative (cross code) number:
CA1505884
150-5884
1505884
CA1505884
150-5884
1505884
Weight: 0.04 pounds 0 kg.
Information:
AXIAL WIDTH
7.9
mm
ID
121.93
mm
MATERIAL
Plastic
OD
129.83
mm
RADIAL HEIGHT
3.95
mm
RING TYPE
ID
EXCAVATOR, WHEELED EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$11.38
07 May 2022
US: Florida-Parts-Z
1505884 - Ring for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$9.92
16 Jan 2019
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
Caterpillar Ring WEAR 1505884 New
$7.63
06 May 2022
0.1102[0.05] Pounds
US: TakePart
CTP Caterpillar Ring (1505884)
CTP
CTP
Number on catalog scheme:
12
For full view, you need register
Compatible equipment models: 1505884:
EXCAVATOR
314C
314D CR
314D LCR
314E CR
314E LCR
318B
318C
319C
319D
319D L
319D LN
320B
320C
322B LN
322C
322C FM
324D
324D FM
324D FM LL
324D L
324D LN
325C
325C FM
345B II
365B
365B II
365B L
365C
365C L
374D L
374F L
M325D L MH
LOGGER
322C
MOBILE HYD POWER UNIT
324D LN
Information:
Engines:
3618 (S/N: 2MW)
Use these guidelines to determine the reusability of the following 3618 Engine components: cylinder head studs, main bearing cap studs, main bearing cap cross tie bolts and connecting rod cap bolts.An overall length has been specified as the maximum acceptable limit for reusability of these bolts and studs. Formerly, these bolts and studs were tightened to a maximum number of times. These bolts and studs will permanently elongate when these bolts and studs are tightened past a certain load level. This elongation is cumulative with each tightening. This allows a maximum limit for the overall length to be established.Before you reuse one of these bolts or studs, perform the following checks:
All of fasteners should be thoroughly inspected before the fasteners are reused. Do not reuse a fastener that has any of the problems that follow: rust, nicks, thread damage, cracks, pits, deformations and any other damage.
If the fastener passes Step 1, measure the length of the fastener. The illustrations show the dimensions to be measured.
Illustration 1 g00795910
This illustration shows the location of the Dimension (A) of a 137-4048 Cylinder Head Stud .
Illustration 2 g00795911
This illustration shows the location of the Dimension (B) of a 137-0134 Connecting Rod Bolt .
Illustration 3 g00795913
This illustration shows the location of the Dimension (C) of a 137-4047 Main Bearing Cap Stud .
Illustration 4 g00795914
This illustration shows the location of Dimension (D) of a 142-0142 Main Bearing Cap Cross Tie Bolt .
For a 137-4048 Cylinder Head Stud, the maximum length for dimension (A) is 769.50 mm (30.295 inch).For a 137-0134 Connecting Rod Bolt, the maximum length for dimension (B) is 246.20 mm (9.693 inch).For a 137-4047 Main Bearing Cap Stud, the maximum length for dimension (C) is 698.50 mm (27.500 inch).For a 142-0142 Main Bearing Cap Cross Tie Bolt, the maximum length for dimension (D) is 280.50 mm (11.043 inch).
If the dimension for maximum length is exceeded, replace that bolt or that stud.
3618 (S/N: 2MW)
Use these guidelines to determine the reusability of the following 3618 Engine components: cylinder head studs, main bearing cap studs, main bearing cap cross tie bolts and connecting rod cap bolts.An overall length has been specified as the maximum acceptable limit for reusability of these bolts and studs. Formerly, these bolts and studs were tightened to a maximum number of times. These bolts and studs will permanently elongate when these bolts and studs are tightened past a certain load level. This elongation is cumulative with each tightening. This allows a maximum limit for the overall length to be established.Before you reuse one of these bolts or studs, perform the following checks:
All of fasteners should be thoroughly inspected before the fasteners are reused. Do not reuse a fastener that has any of the problems that follow: rust, nicks, thread damage, cracks, pits, deformations and any other damage.
If the fastener passes Step 1, measure the length of the fastener. The illustrations show the dimensions to be measured.
Illustration 1 g00795910
This illustration shows the location of the Dimension (A) of a 137-4048 Cylinder Head Stud .
Illustration 2 g00795911
This illustration shows the location of the Dimension (B) of a 137-0134 Connecting Rod Bolt .
Illustration 3 g00795913
This illustration shows the location of the Dimension (C) of a 137-4047 Main Bearing Cap Stud .
Illustration 4 g00795914
This illustration shows the location of Dimension (D) of a 142-0142 Main Bearing Cap Cross Tie Bolt .
For a 137-4048 Cylinder Head Stud, the maximum length for dimension (A) is 769.50 mm (30.295 inch).For a 137-0134 Connecting Rod Bolt, the maximum length for dimension (B) is 246.20 mm (9.693 inch).For a 137-4047 Main Bearing Cap Stud, the maximum length for dimension (C) is 698.50 mm (27.500 inch).For a 142-0142 Main Bearing Cap Cross Tie Bolt, the maximum length for dimension (D) is 280.50 mm (11.043 inch).
If the dimension for maximum length is exceeded, replace that bolt or that stud.
Cat SIS web machinery list:
Parts ring Caterpillar catalog:
345C, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 385B, 385C, 385C L, 390D, 390D L, 390F L
345C, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 375, 375 L, 385B, 385C L
325 L, 325C, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 345B II, 345C, 345C L, 365B, 365B II, 365B L, 365C, 36...
345C, 345C L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, D10, D9G, D9H
325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330D FM, 350, 350 L, CR20, M325B, M325C MH, M325D L MH, P16, S25
350, 350 L, 365B, 375, 375 L, CR20, P16, S25
330, 345B, 345B II, 345B L, 345C, 345C L, 350, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH
365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L
365C L, 385C, 385C L, 390F L
325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330D FM, 345B II, 345B L, 345C, 350, 350 L, 365B, 365B II, M325B, M325C MH, M325D L MH
345B II, 345B L, 345C, 365B
345B II, 345B L, 345C, 365B
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, TK711, TK721, TK722, TK732, TK741, T...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, TK711, TK721, TK722, TK732, TK741, T...
1038379
RING
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 320E LN, 320N, 321D LCR, 322 FM L, 322 LN, 322B...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 320E LN, 320N, 321D LCR, 322 FM L, 322 LN, 322B...
1038378
RING-RETAINING
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 320E LN, 320N, 321D LCR, 322 FM L, 322 LN, 322B...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 320E LN, 320N, 321D LCR, 322 FM L, 322 LN, 322B...
1930560
RING
318B
318B
1930558
RING-HALF
318B
318B
0931571
RING-RETAINING
1090, 1190, 1190T, 1290T, 2290, 2390, 2391, 2491, 312, 318B, 320, 320B, 320B FM LL, 320C, 320C FM, 320D, 320E, 320E L, 320E RR, 321B, 321C, 321D LCR, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C...
1090, 1190, 1190T, 1290T, 2290, 2390, 2391, 2491, 312, 318B, 320, 320B, 320B FM LL, 320C, 320C FM, 320D, 320E, 320E L, 320E RR, 321B, 321C, 321D LCR, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C...
1874804
RING
318B
318B
1090, 1190, 1190T, 1290T, 2290, 2390, 2391, 2491, 318B, 320C, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 325B L, 325C, 325C L, 325D MH, 330C, 511, 521, 521B, 522, 522B, 532, 834G, 834H, 834K, 8...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320E LN, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 32...
7Y4631
RING-RETAINING
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E LN, 321D LCR, 323D L, 323D LN, 323...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E LN, 321D LCR, 323D L, 323D LN, 323...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 321D LCR, 323D L, 323D LN, 323D SA, 325, 325 L, 325 LN, 325B L, 325C, 325D L, ...