1890593 RING-WEAR Caterpillar parts
902, 906, 906H, 907H, 908, 908H
Rating:
Alternative (cross code) number:
CA1890593
189-0593
1890593
CA1890593
189-0593
1890593
Weight: 0.01 pounds 0 kg.
Information:
AXIAL WIDTH
24.7
mm
ID
31.75
mm
OD
0
mm
THICKNESS
1.4
mm
TYPE
ROD
COMPACT WHEEL LOADER,
Number on catalog scheme:
12
For full view, you need register
Information:
The Electronic Control Module (ECM) supplies a regulated voltage of 8.0 0.4 VDC to the throttle sensor.This procedure covers the following diagnostic codes:
041-03 8 Volt DC Supply short to +batt
041-04 8 Volt DC Supply short to groundA +8 V diagnostic code is probably caused by a short circuit to ground or a short circuit to another voltage source in the harness. The next likely cause is a problem with a sensor. The least likely cause is a problem with the ECM.
Illustration 1 g01234104
Schematic for the digital sensor supply
Test Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 2 g01234113
Typical left side view
(1) J1/P1 ECM connectors
Thoroughly inspect connector (1). Inspect the connectors for each digital sensor. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Illustration 3 g01234119
P1 ECM connector
(P1-4) +8 VDC
(P1-5) Return
(P1-66) Throttle position signal
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the digital sensor supply.
Check the torque of the allen head screws for the ECM connectors. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Check the harness and wiring for abrasions and for pinch points from the battery to the ECM. Expected Result:All of the connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion or of pinch points.Results:
OK - The connectors and the wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem with a connector and/or the wiring.Repair: Repair the connector and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the problem is resolved.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector. Refer to electronic troubleshooting Troubleshooting, "Electronic Service Tools".
Restore the electrical power to the ECM.
Observe the active diagnostic code screen on Cat ET. Wait at least 30 seconds so that any codes may become active. Look for these codes:
041-03 8 Volt DC Supply short to +batt
041-04 8 Volt DC Supply short to groundExpected Result:One of the above diagnostic codes is active.Results:
Active 03 code - A 03 diagnostic code is active. Proceed to Test Step 3.
Active 04 code - A 04 diagnostic code is active. Proceed to Test Step 4.
No active codes - None of the above codes are active.Repair: If any of the above codes are logged and the engine is not running properly, refer to Troubleshooting, "Troubleshooting Without a Diagnostic Code".If the engine is running properly at this time, there may be an intermittent problem in a harness that is causing the codes to be logged. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".STOPTest Step 3. Check the Voltage on the +8 V Supply Wire
Remove the electrical power from the ECM.
Disconnect the
041-03 8 Volt DC Supply short to +batt
041-04 8 Volt DC Supply short to groundA +8 V diagnostic code is probably caused by a short circuit to ground or a short circuit to another voltage source in the harness. The next likely cause is a problem with a sensor. The least likely cause is a problem with the ECM.
Illustration 1 g01234104
Schematic for the digital sensor supply
Test Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 2 g01234113
Typical left side view
(1) J1/P1 ECM connectors
Thoroughly inspect connector (1). Inspect the connectors for each digital sensor. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Illustration 3 g01234119
P1 ECM connector
(P1-4) +8 VDC
(P1-5) Return
(P1-66) Throttle position signal
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the digital sensor supply.
Check the torque of the allen head screws for the ECM connectors. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Check the harness and wiring for abrasions and for pinch points from the battery to the ECM. Expected Result:All of the connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion or of pinch points.Results:
OK - The connectors and the wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem with a connector and/or the wiring.Repair: Repair the connector and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the problem is resolved.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector. Refer to electronic troubleshooting Troubleshooting, "Electronic Service Tools".
Restore the electrical power to the ECM.
Observe the active diagnostic code screen on Cat ET. Wait at least 30 seconds so that any codes may become active. Look for these codes:
041-03 8 Volt DC Supply short to +batt
041-04 8 Volt DC Supply short to groundExpected Result:One of the above diagnostic codes is active.Results:
Active 03 code - A 03 diagnostic code is active. Proceed to Test Step 3.
Active 04 code - A 04 diagnostic code is active. Proceed to Test Step 4.
No active codes - None of the above codes are active.Repair: If any of the above codes are logged and the engine is not running properly, refer to Troubleshooting, "Troubleshooting Without a Diagnostic Code".If the engine is running properly at this time, there may be an intermittent problem in a harness that is causing the codes to be logged. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".STOPTest Step 3. Check the Voltage on the +8 V Supply Wire
Remove the electrical power from the ECM.
Disconnect the
Caterpillar parts catalog:
Parts ring Caterpillar catalog:
173B, 183B, 193, 24H, 24M, 3408, 3408C, 3408E, 527, 561N, 572R II, 589, 65, 735, 740, 902, 906, 914G, 938K, 939C, AD30, CX35-P800, D10N, D10R, D10T, D10T2, D350E II, D400E II, D4C III, D4H, D5C III, D...
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H NA, 3304, 3306, 528, 906H, 907H, 908H, 924G, 924GZ, 938G, 938G II, 943, 950G, 950...
3208, 3304, 3306, 3406, 3406B, 3408, 515, 518C, 525, 528B, 530B, 589, 631E, 637E, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 8...
24H, 24M, 561H, 561M, 561N, 572R, 572R II, 776C, 776D, 777B, 777D, 777F, 777G, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836,...
215, 225, 227, 235, 235B, 235C, 235D, 245, 24H, 320B FM LL, 330, 578, 583R, 589, 621, 621E, 621F, 621G, 623B, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 639...
906H, 906H2, 907H, 907H2, 908H, 908H2, AP1000E, AP1055E, BG1000E, BG1055E, CB-434D, CB-44B, CB-534C, CB-534D, CB-54, CB-54B, CB-564D, CB-634C, CB-634D, CB-64, CD-54, CD-54B, CP-533E, CP-56, CP-573E, C...
906H, 906H2, 907H, 907H2, 908H, 908H2, AP1000E, AP1055E, BG1000E, BG1055E, CB-434B, CB-434C, CB-434D, CB-44B, CB-534C, CB-534D, CB-54, CB-54B, CB-564D, CB-634C, CB-634D, CB-64, CD-54, CD-54B, CP-533E,...
307, 307B, 307C, 307D, 308C, 308D, 324D L, 325D MH, 330D, 330D L, 330D MH, 345C, 345C MH, 621H, 621K, 627H, 627K, 627K LRC, 906H, 906H2, 907H, 907H2, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, E70B, M312, ...
312C, 312D, 315C, 315D L, 318C, 319C, 319D, 319D LN, 320B, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B...
302.5, 302.5C, 908
12F, 14E, 215, 215B, 225, 227, 229, 312D, 320B, 320C, 323D LN, 323D SA, 323E L, 325B L, 325C, 325D, 325D L, 325D MH, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330, 330B L, 330C, 330C L, ...
325C, 328D LCR, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 55, 56...
1890589
RING-WEAR
902, 906, 906H, 907H, 908, 908H
902, 906, 906H, 907H, 908, 908H
1890215
RING-BACKUP
902, 906, 906H, 907H, 908, 908H
902, 906, 906H, 907H, 908, 908H
1402380
RING-WEAR
902, 906, 906H, 906H2, 907H, 907H2, 908, 908H, 908H2, AD30, AD45B
902, 906, 906H, 906H2, 907H, 907H2, 908, 908H, 908H2, AD30, AD45B
1642935
RING-SUPPORT
938G, 950G, 962G, 966G, 972G, IT38G
938G, 950G, 962G, 966G, 972G, IT38G
325C, 330C, 330C L, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 374D L, 390D, 390D L, IT62G, W345B II, W345C...
0951793
RING-BACKUP
325D L, 345D, 345D L, 345D L VG, 349D, 349D L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B, 5110B, IT62G
325D L, 345D, 345D L, 345D L VG, 349D, 349D L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B, 5110B, IT62G
2158133
RING
924G, 924GZ, 924H, 924HZ
924G, 924GZ, 924H, 924HZ
1767608
RING
924G, 924GZ
924G, 924GZ
140B, 14E, 613, 615, 623F, 623G, 623H, 623K, 623K LRC, 650B, 910
539, 623F, D7R II, D7R XR
1491284
RING-RETAINING
906, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-634C
906, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-634C
1695777
RING-RETAINING
345B II, 902, 906, 908
345B II, 902, 906, 908