1S6480 RING Caterpillar parts
824B, D4D
Rating:
Alternative (cross code) number:
CA1S6480
1S-6480
1S6480
CA1S6480
1S-6480
1S6480
Weight: 0.010 pounds 0 kg.
TRACK-TYPE TRACTOR, WHEEL DOZER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
8S3370 - Ring-Seal 1S6480 for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$62.13
27 May 2023
0.26[0.12] Pounds
Amazon.com
WVE by NTK 1S6480 Ignition Switch, 1 Pack
WVE by NTK Ignition starter switch directs current from the fuse panel to other systems in the vehicle || When not replaced, vehicle may experience no-start, intermittent shut down and/or current will not flow to all systems || Designed to meet or exceed OE specifications in form, fit and function || Global coverage for import and/or domestic applications
WVE by NTK Ignition starter switch directs current from the fuse panel to other systems in the vehicle || When not replaced, vehicle may experience no-start, intermittent shut down and/or current will not flow to all systems || Designed to meet or exceed OE specifications in form, fit and function || Global coverage for import and/or domestic applications
$40.15
17 May 2022
0.26[0.12] Pounds
US: Auto Accessory
WVE by NTK 1S6480 Ignition Switch, 1 Pack
WVE by NTK Ignition starter switch directs current from the fuse panel to other systems in the vehicle || When not replaced, vehicle may experience no-start, intermittent shut down and/or current will not flow to all systems || Designed to meet or exceed OE specifications in form, fit and function || Global coverage for import and/or domestic applications
WVE by NTK Ignition starter switch directs current from the fuse panel to other systems in the vehicle || When not replaced, vehicle may experience no-start, intermittent shut down and/or current will not flow to all systems || Designed to meet or exceed OE specifications in form, fit and function || Global coverage for import and/or domestic applications
Number on catalog scheme:
8
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
B 8T-5096 Dial Indicator 1
C 8T-3052 Degree Wheel 1 Start By:
Remove the engine oil pump.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Check the main bearing caps for identification of the location and check the direction of the main bearing caps in relation to the cylinder block. The main bearing caps must be installed in the original location and the original direction.
Illustration 1 g00996899
Remove bolts (1) from No. 2 through No. 6 main bearing caps (2). Note: Remove No. 1 and No. 7 main bearing caps (2) after No. 2 through No. 6 main bearing caps have been installed.
Illustration 2 g01020288
Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft in order to remove upper main bearing (3) from the cylinder block. Note: Push the upper main bearing from the opposite side of the bearing tab with Tooling (A). If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft.
Illustration 3 g01134355
Remove thrust plates (4) from each side of the No. 4 main bearing.
Remove the lower halves of the main bearings from the main bearing caps. Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.
Illustration 4 g01020300
Position the new upper main bearing (3) on the crankshaft. Insert the end of the upper main bearing that does not have the tab into the cylinder block. Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft in order to push the upper main bearing into the cylinder block. Note: Push the upper main bearing from the side of the bearing tab with Tooling (A). If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft.
Illustration 5 g01134355
Install thrust plates (4) on each side of the No. 4 main bearing. Note: Install the thrust plates with the words "Block Side" toward the cylinder block.
Install the lower halves of the crankshaft main bearings in the main bearing caps. Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the main bearing caps.
Illustration 6 g01018383
Position main bearing caps (2) on the crankshaft. Note: Ensure that
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
B 8T-5096 Dial Indicator 1
C 8T-3052 Degree Wheel 1 Start By:
Remove the engine oil pump.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Check the main bearing caps for identification of the location and check the direction of the main bearing caps in relation to the cylinder block. The main bearing caps must be installed in the original location and the original direction.
Illustration 1 g00996899
Remove bolts (1) from No. 2 through No. 6 main bearing caps (2). Note: Remove No. 1 and No. 7 main bearing caps (2) after No. 2 through No. 6 main bearing caps have been installed.
Illustration 2 g01020288
Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft in order to remove upper main bearing (3) from the cylinder block. Note: Push the upper main bearing from the opposite side of the bearing tab with Tooling (A). If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft.
Illustration 3 g01134355
Remove thrust plates (4) from each side of the No. 4 main bearing.
Remove the lower halves of the main bearings from the main bearing caps. Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.
Illustration 4 g01020300
Position the new upper main bearing (3) on the crankshaft. Insert the end of the upper main bearing that does not have the tab into the cylinder block. Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft in order to push the upper main bearing into the cylinder block. Note: Push the upper main bearing from the side of the bearing tab with Tooling (A). If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft.
Illustration 5 g01134355
Install thrust plates (4) on each side of the No. 4 main bearing. Note: Install the thrust plates with the words "Block Side" toward the cylinder block.
Install the lower halves of the crankshaft main bearings in the main bearing caps. Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the main bearing caps.
Illustration 6 g01018383
Position main bearing caps (2) on the crankshaft. Note: Ensure that
Caterpillar parts catalog:
Parts ring Caterpillar catalog:
1S7349
RING
621, 980, D4D
621, 980, D4D
5K2382
RING
941, 951B, 955H, 955K, 955L
941, 951B, 955H, 955K, 955L
621G, 623G, 627G, 631G, 637G, 657E, 657G, 725, 730, 735, 735B, 740, 740B, 814, 816, 824G II, 824H, 834G, 834H, 836G, 836H, 950, 955K, 955L, 966C, AD30, D250E II, D300E II, D350E II, D400E II, D5, D5B
561B, 561C, 977D, 977H, D5
941, 955C, 955H, D4D
120, 120G, 130G, 16, 941, 951B, 955K, 955L, D4D, D5, D5B
3J0699
RING
163, 977D
163, 977D
6J1576
RING
951B
951B
613, 651, 657, 657B, 666, 769, 834, 920, 930, 941, 951B, D4D
518, 518C, 528, 528B, 530B, 735, 735B, 740, 740B, 797, 797B, 797F, 920, 930, 941, 951B, D10, D4D, D6H
518, 518C, 528, 528B, 530B, 797, 797B, 797F, 920, 930, 941, 951B, D4D
518, 528, 920, 930, 941, 951B, D4D