2835972 RING-SEAL Caterpillar parts
312C L, 312D, 312D L, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E LCR
Rating:
Alternative (cross code) number:
CA2835972
283-5972
2835972
CA2835972
283-5972
2835972
Weight: 0.02 pounds 0 kg.
EXCAVATOR,
Compatible equipment models: 2835972:
Number on catalog scheme:
16
For full view, you need register
Information:
Clean the cooling system and flush the cooling system before the recommended maintenance interval if the following conditions exist:
The engine overheats frequently.
Foaming is observed.
The oil has entered the cooling system and the coolant is contaminated.
The fuel has entered the cooling system and the coolant is contaminated.
Use of commercially available cooling system cleaners may cause damage to cooling system components. Use only cooling system cleaners that are approved for Caterpillar engines.
Note: Inspect the water pump and the water temperature regulator after the cooling system has been drained. This is a good opportunity to replace the water pump, the water temperature regulator and the hoses, if necessary. Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove one of the drain plugs. Note: If equipped, be sure to drain the heater and any related supply and return lines.Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Caterpillar Service Technology Group:Outside Illinois 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual, SENR3130, "Torque Specifications" for more information on the proper torques.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with a mixture of clean water and Caterpillar Fast Acting Cooling System Cleaner. Add 0.5 L (1 pint) of cleaner per 15 L (4 US gal) of the cooling system capacity. Install the cooling system filler cap.
Start and run the engine at low idle for a minimum of 30 minutes. The coolant temperature should be at least 82 °C (180 °F).
Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with
The engine overheats frequently.
Foaming is observed.
The oil has entered the cooling system and the coolant is contaminated.
The fuel has entered the cooling system and the coolant is contaminated.
Use of commercially available cooling system cleaners may cause damage to cooling system components. Use only cooling system cleaners that are approved for Caterpillar engines.
Note: Inspect the water pump and the water temperature regulator after the cooling system has been drained. This is a good opportunity to replace the water pump, the water temperature regulator and the hoses, if necessary. Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove one of the drain plugs. Note: If equipped, be sure to drain the heater and any related supply and return lines.Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Caterpillar Service Technology Group:Outside Illinois 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual, SENR3130, "Torque Specifications" for more information on the proper torques.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with a mixture of clean water and Caterpillar Fast Acting Cooling System Cleaner. Add 0.5 L (1 pint) of cleaner per 15 L (4 US gal) of the cooling system capacity. Install the cooling system filler cap.
Start and run the engine at low idle for a minimum of 30 minutes. The coolant temperature should be at least 82 °C (180 °F).
Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with
Caterpillar parts catalog:
Parts ring Caterpillar catalog:
312C L, 318C, 319C, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR,...
311B, 312E, 312E L, 316E L, 318E L, 320E, 320E L, 320E LN, 323E L, 324E, 324E L, 324E LN, 325B, 329E, 329E L, 329E LN, 350, 365B, 365B L, 375, 385B, 901C, 902C, 903C, 904B, 904H, D3K XL, D4K XL, D5K L...
1090, 1190, 1190T, 1290T, 1390, 24H, 312C, 312D, 315C, 315D L, 318C, 319C, 319D, 320 L, 320B, 320C, 320C L, 320D, 320E L, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 324D, 324D FM, 324D FM LL, 32...
312C, 312D, 315C, 315D L, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D...
308C, 311, 311B, 311C, 311D LRR, 312D, 312D L, 312E, 312E L, 313D, 314D CR, 314D LCR, 314E CR, 314E LCR, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 324D, 324D L, 324E, 324E L, 324E LN, 329D,...
311D LRR, 312D, 312D L, 312E, 312E L, 313D, 314D CR, 314D LCR, 314E CR, 314E LCR, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 324D, 324D L, 324E, 324E L, 324E LN, 329D, 329D L, 329D LN, 329E,...
312D, 325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330D FM, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 350, 350 L, 365B, 365B II, ...
312D, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C L MH, 966K, 966M, 966M XE, 972K, 972M,...
312D, 330D FM, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C L MH, 568 FM LL
312D, 345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C L MH, 982M
312D, 345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C L MH, 966K, 966M, 966M XE, 972K, 972M,...
12F, 14E, 215, 215B, 225, 227, 229, 312D, 320B, 320C, 323D LN, 323D SA, 323E L, 325B L, 325C, 325D, 325D L, 325D MH, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330, 330B L, 330C, 330C L, ...
1027142
RING
308C, 308E CR, 308E SR, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 321C, 321D LCR, 325C, 328D LCR
308C, 308E CR, 308E SR, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 321C, 321D LCR, 325C, 328D LCR
9T0836
RING-RETAINING
311C, 318C, 319C, 320C, 320C FM, 320D, 320D FM, 320D L, 320D LRR, 320D RR, 320D2, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321C, 321D LCR, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 32...
311C, 318C, 319C, 320C, 320C FM, 320D, 320D FM, 320D L, 320D LRR, 320D RR, 320D2, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321C, 321D LCR, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 32...
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
0995368
RING
308C, 311, 311B, 311C, 311D LRR, E110B
308C, 311, 311B, 311C, 311D LRR, E110B
311, 312, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
1352350
RING-PISTON
311, 318C, 319C, 320B, 320B U, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
311, 318C, 319C, 320B, 320B U, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
1352354
RING-PISTON
311, 318C, 319C, 320B, 320B U, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
311, 318C, 319C, 320B, 320B U, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
1352356
RING-THRUST
311, 318C, 319C, 320B, 320B U, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
311, 318C, 319C, 320B, 320B U, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
1352352
RING-RETAINING
311, 318C, 319C, 320B, 320B U, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
311, 318C, 319C, 320B, 320B U, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
3888368
RING-RETAINING
312D2 L, 314C, 318D2 L
312D2 L, 314C, 318D2 L