3220649 RING Caterpillar parts
Rating:
Alternative (cross code) number:
CA3220649
322-0649
3220649
CA3220649
322-0649
3220649
Weight: 0.04 pounds 0 kg.
Information:
On/Off Time Delay (Relay)
Performance Check
Illustration 1 g00510020
On/Off Time Delay (Relay)
The following items are required for the performance check:
Battery or DC source of 8 to 40 volts
Voltmeter ( 6V-7070 Digital Multimeter or one of same accuracy)
Stop watch
Bench test or installed testConnect the source voltage to negative relay terminal (8) and positive relay terminal (4). During a bench test, connect the positive voltage to relay terminal (6). The connections must be maintained until the tests are complete.Note: There will be voltage when the relay is closed. When the relay is open, there will be no voltage. The voltage may be positive or negative when the relay is tested on the engine. The voltage will always be positive during a bench test.
Use a voltmeter in order to verify the information in Table 1.
Table 1
Terminal Relay Position    
Terminals     Relay Position    
5     Closed    
7     Open    
Apply Positive Source Voltage To Terminal (1) .Immediately verify Table 2. (Do not leave the voltage on terminal (1) for more than 60 seconds.)
Table 2
Terminal Relay Position    
Terminals     Relay Position    
5     Open    
7     Closed    
Remove Positive Source Voltage From Terminal (1) .Use a stop watch in order to check the time from the moment of removal in order to verify Table 3.
Table 3
Terminals     Delay Time to Function    
0 to 60 sec.     After 80 sec.    
5     Open     Closed    
7     Closed     Open    
Apply Positive Source Voltage To Terminal (2) .Note: In bench testing, Step 6 can be used. When the unit is installed on the engine, all wires must be disconnected from terminal (2) in order to prevent a direct short.Check the time when the voltage is applied in order to verify Table 4. (Do not leave the voltage on terminal (2) for more than 60 seconds.)
Table 4
Terminals     Delay Time to Function    
0 to 8 sec.     After 10 sec.    
5     Closed     Open    
7     Open     Closed    
Remove Positive Source Voltage From Terminal (2) .Check the time from the moment of removal in order to verify Table 5.
Table 5
Terminals     Delay Time to Function    
0 to 60 sec.     After 80 sec.    
5     Open     Closed    
7     Closed     Open    
Remove Wire From Terminal (4) .Verify Table 6.
Table 6
Terminal Relay Position    
Terminals     Relay Position    
5     Closed    
7     Open    
Performance Check
Illustration 1 g00510020
On/Off Time Delay (Relay)
The following items are required for the performance check:
Battery or DC source of 8 to 40 volts
Voltmeter ( 6V-7070 Digital Multimeter or one of same accuracy)
Stop watch
Bench test or installed testConnect the source voltage to negative relay terminal (8) and positive relay terminal (4). During a bench test, connect the positive voltage to relay terminal (6). The connections must be maintained until the tests are complete.Note: There will be voltage when the relay is closed. When the relay is open, there will be no voltage. The voltage may be positive or negative when the relay is tested on the engine. The voltage will always be positive during a bench test.
Use a voltmeter in order to verify the information in Table 1.
Table 1
Terminal Relay Position    
Terminals     Relay Position    
5     Closed    
7     Open    
Apply Positive Source Voltage To Terminal (1) .Immediately verify Table 2. (Do not leave the voltage on terminal (1) for more than 60 seconds.)
Table 2
Terminal Relay Position    
Terminals     Relay Position    
5     Open    
7     Closed    
Remove Positive Source Voltage From Terminal (1) .Use a stop watch in order to check the time from the moment of removal in order to verify Table 3.
Table 3
Terminals     Delay Time to Function    
0 to 60 sec.     After 80 sec.    
5     Open     Closed    
7     Closed     Open    
Apply Positive Source Voltage To Terminal (2) .Note: In bench testing, Step 6 can be used. When the unit is installed on the engine, all wires must be disconnected from terminal (2) in order to prevent a direct short.Check the time when the voltage is applied in order to verify Table 4. (Do not leave the voltage on terminal (2) for more than 60 seconds.)
Table 4
Terminals     Delay Time to Function    
0 to 8 sec.     After 10 sec.    
5     Closed     Open    
7     Open     Closed    
Remove Positive Source Voltage From Terminal (2) .Check the time from the moment of removal in order to verify Table 5.
Table 5
Terminals     Delay Time to Function    
0 to 60 sec.     After 80 sec.    
5     Open     Closed    
7     Closed     Open    
Remove Wire From Terminal (4) .Verify Table 6.
Table 6
Terminal Relay Position    
Terminals     Relay Position    
5     Closed    
7     Open    
Caterpillar parts catalog:
Parts ring Caterpillar catalog:
3208581
RING-SNAP
Caterpillar
Caterpillar
3207373
RING-SNAP
Caterpillar
Caterpillar
3207312
RING-SNAP
Caterpillar
Caterpillar
3207309
RING-SEAL
Caterpillar
Caterpillar
3096307
RING-RETAINING
Caterpillar
Caterpillar
3096306
RING-RETAINING
Caterpillar
Caterpillar
3344921
RING-RETAINING
Caterpillar
Caterpillar
3310906
RING
Caterpillar
Caterpillar
3237222
RING
Caterpillar
Caterpillar
3220714
RING
Caterpillar
Caterpillar
3220699
RING-BACKUP
Caterpillar
Caterpillar
3220696
RING-BACKUP
Caterpillar
Caterpillar