AVSPARE.COM
parts catalog

RING-DAMPER 3236652 - Caterpillar



3236652 RING-DAMPER Caterpillar parts RING
Rating:
66
Alternative (cross code) number:
CA3236652
323-6652
3236652
Caterpillar 3236652 RING-DAMPER
Weight: 0.06 pounds 0 kg.

Buy RING-DAMPER 3236652 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Disassemble the brake assembly by the following steps:
Remove springs (17) and (21).
Remove socket (18) and nut (20).
Remove adjustment screw (19) from nut (20).
Illustration 9 g06293157
Remove retaining rings (28) and (31).
Remove anchor pin brace (29).
Remove brake shoes (22) and (26) from plate assembly (32).
Remove nuts (23) and (25).
Remove camshaft (24) from plate assembly (32).
Remove pins (27) and (30) from plate assembly (32).Installation Procedure
Check the condition of the lining and the brake shoe assemblies. Use new parts for replacement if the components are worn or damaged.
Illustration 10 g06293157
Assemble the brake assembly by the following steps:
Install pins (27) and (30) to plate assembly (32).
Install camshaft (24) to plate assembly (32).
Install nuts (23) and (25). Tighten nuts (23) and (25) to a torque of 169.5 to 226.0 N.m (125.0 to 166.7 lb ft).
Install brake shoes (22) and (26) to plate assembly (32).
Install anchor pin brace (29).
Install retaining rings (28) and (31).
Illustration 11 g06293148
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install adjustment screw (19) to nut (20).
Install socket (18) and nut (20).
Install springs (21) and (17).
Illustration 12 g06293146
Install brake assembly (16) and bolts (15). Tighten bolts (15) to a torque of 270 40 N.m (199 30 lb ft).
Illustration 13 g06293144
Use two people to install brake drum (11) and yoke assembly (12). The combined weight of brake drum (11) and yoke assembly (12) is approximately 32 kg (71 lb). Install brake drum (11) and yoke assembly (12) as a unit.
Install the O-ring seal, retainer (13), and bolt (14). Tighten bolt (14) to a torque of 135 15 N m (100 11 lb ft).
Illustration 14 g06293130
Position plate (10) and install bolts (9).
Illustration 15 g06290648
Illustration 16 g06290647
Typical example
Install parking brake actuator lever (8) and bolt (5).
Use Tooling (A) to apply pressure to parking brake actuator (4) to align yoke assembly (7) with parking brake actuator lever (8).
Apply Tooling (B) to clevis pin (6), parking brake lever (8), and yoke assembly (7). Install clevis pin (6) and the cotter pin.
Illustration 17 g00546845
Turn Knob (B) on Tooling (A) to release the pressure in the parking brake actuator. Remove Tooling (A) from the parking brake actuator.
Illustration 18 g06290646
Connect hose assembly (3) to parking brake actuator (4).
Adjust parking brake actuator (4). Refer to Testing and Adjusting, "Parking Brake Actuator - Adjust" for the proper adjustment of parking brake actuator (4).
Illustration 19 g06290641
Use Tooling (C) to install guard (2). The weight of guard (2) is approximately 29 kg (64 lb). Install guard (2) and bolts (1).End By:
Install the drive shaft (center).


Parts ring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.