3402376 RING-RETAINING Caterpillar parts
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
Rating:
Alternative (cross code) number:
CA3402376
340-2376
3402376
CA3402376
340-2376
3402376
Weight: 0.47 pounds 0 kg.
TRUCK,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Sunsong 3402376 Power Steering Return Line Hose Assembly
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a Max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade Steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Each Hose is precision engineered to exact fit and Includes brackets, grommets, heat shields, bushings, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Hoses are made from multi-layer reinforced rubber and have a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature range of -40 to 275 degrees Fahrenheit, exceeding original equipment requirements || Fit type: Vehicle Specific
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a Max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade Steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Each Hose is precision engineered to exact fit and Includes brackets, grommets, heat shields, bushings, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Hoses are made from multi-layer reinforced rubber and have a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature range of -40 to 275 degrees Fahrenheit, exceeding original equipment requirements || Fit type: Vehicle Specific
Sunsong 3402376 Power Steering Return Line Hose Assembly
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a Max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade Steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Each Hose is precision engineered to exact fit and Includes brackets, grommets, heat shields, bushings, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Hoses are made from multi-layer reinforced rubber and have a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature range of -40 to 275 degrees Fahrenheit, exceeding original equipment requirements || Fit type: Vehicle Specific
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a Max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade Steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Each Hose is precision engineered to exact fit and Includes brackets, grommets, heat shields, bushings, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Hoses are made from multi-layer reinforced rubber and have a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature range of -40 to 275 degrees Fahrenheit, exceeding original equipment requirements || Fit type: Vehicle Specific
Sunsong 3402376 Power Steering Return Line Hose Assembly
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a Max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade Steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Each Hose is precision engineered to exact fit and Includes brackets, grommets, heat shields, bushings, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Hoses are made from multi-layer reinforced rubber and have a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature range of -40 to 275 degrees Fahrenheit, exceeding original equipment requirements || Fit type: Vehicle Specific
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a Max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade Steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Each Hose is precision engineered to exact fit and Includes brackets, grommets, heat shields, bushings, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Hoses are made from multi-layer reinforced rubber and have a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature range of -40 to 275 degrees Fahrenheit, exceeding original equipment requirements || Fit type: Vehicle Specific
Number on catalog scheme:
7B
For full view, you need register
Information:
Introduction
This procedure is intended to give information on inspection the valve guide.Perform this test in order to determine if a valve guide should be replaced. Required Tools
Table 1
Required Tools
Part Number Part Name Qty
8T-5096 Dial Indicator Group 1 Check Procedure
Illustration 1 g00986821
(1) Valve guide
(2) Radial movement of the valve in the valve guide
(3) Valve stem
(4) Dial indicator
(5) Valve head
Place a new valve in the valve guide.
Place the dial indicator with the magnetic base on the face of the cylinder head.
Lift the edge of the valve head to a distance of 15.0 mm (0.60 inch).
Move the valve in a radial direction away from the dial indicator. Make sure that the valve moves away from the dial indicator as far as possible. Position the contact point of the dial indicator on the edge of the valve head. Set the position of the needle of the dial indicator to zero.
Move the valve in a radial direction toward the dial indicator as far as possible. Note the distance of movement which is indicated on the dial indicator. If the distance is greater than the maximum clearance of the valve in the valve guide, replace the valve guide.
When new valve guides are installed, new valves and new valve seat inserts must be installed. Valve guides and valve seat inserts are supplied as an unfinished part. The unfinished valve guides and unfinished valve seat inserts are installed in the cylinder head. Then, the valve guides and valve inserts are cut and reamed in one operation with special tooling
Refer to Specifications, "Cylinder Head Valves" for the maximum clearance of the valve in the valve guide.
This procedure is intended to give information on inspection the valve guide.Perform this test in order to determine if a valve guide should be replaced. Required Tools
Table 1
Required Tools
Part Number Part Name Qty
8T-5096 Dial Indicator Group 1 Check Procedure
Illustration 1 g00986821
(1) Valve guide
(2) Radial movement of the valve in the valve guide
(3) Valve stem
(4) Dial indicator
(5) Valve head
Place a new valve in the valve guide.
Place the dial indicator with the magnetic base on the face of the cylinder head.
Lift the edge of the valve head to a distance of 15.0 mm (0.60 inch).
Move the valve in a radial direction away from the dial indicator. Make sure that the valve moves away from the dial indicator as far as possible. Position the contact point of the dial indicator on the edge of the valve head. Set the position of the needle of the dial indicator to zero.
Move the valve in a radial direction toward the dial indicator as far as possible. Note the distance of movement which is indicated on the dial indicator. If the distance is greater than the maximum clearance of the valve in the valve guide, replace the valve guide.
When new valve guides are installed, new valves and new valve seat inserts must be installed. Valve guides and valve seat inserts are supplied as an unfinished part. The unfinished valve guides and unfinished valve seat inserts are installed in the cylinder head. Then, the valve guides and valve inserts are cut and reamed in one operation with special tooling
Refer to Specifications, "Cylinder Head Valves" for the maximum clearance of the valve in the valve guide.
Cat SIS web machinery list:
Parts ring Caterpillar catalog:
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
14G, 14H, 14H NA, 16G, 16H, 16H NA, 518, 518C, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 797
793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, D10, D10N, D10R, D11N, D11R, D11T
3088600
RING
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
3088599
RING
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
2950248
RING
793F, 793F CMD, 793F OEM, 793F-XQ
793F, 793F CMD, 793F OEM, 793F-XQ
3550650
RING
793F, 793F CMD, 793F OEM
793F, 793F CMD, 793F OEM
3471758
RING-WEAR
797F
797F
3991672
RING-LOCK
795F AC, 797F
795F AC, 797F
3859186
RING-SEALING
795F AC, 795F XQ
795F AC, 795F XQ
3859088
RING-SEALING
795F AC, 795F XQ
795F AC, 795F XQ
3113917
RING-RETAINING
795F AC, 795F XQ
795F AC, 795F XQ
4394503
RING-BACKUP
773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM
773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM
8T5015
RING-RETAINING
773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM, CP-433E, CP-44, CS-423E, CS-433E, CS-44
773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM, CP-433E, CP-44, CS-423E, CS-433E, CS-44
3122838
RING
770G, 770G OEM, 772G, 772G OEM, 773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM, 777G
770G, 770G OEM, 772G, 772G OEM, 773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM, 777G