4M8910 RING Caterpillar parts
518, 518C, 528, 528B, 530B, 589, 594H, 631C, 631E, 631G, 633C, 633D, 633E II, 637D, 637E, 637G, 657B, 657E, 657G, 7155, D10, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8H, D8K, D8L, D9G, D9H, D9L, D9...
Rating:
Alternative (cross code) number:
CA4M8910
4M-8910
4M8910
CA4M8910
4M-8910
4M8910
Weight: 0.08 pounds 0 kg.
Information:
OD
90.17
mm
THICKNESS
2.82
mm
TYPE
SPIRAL
PIPELAYER, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$18.29
15 Jun 2023
Amazon.com
CTP 4M8910 Retaining Ring for Heavy Equipment
CTP Ring Only || Sold in each || Easy in-and-out fit
CTP Ring Only || Sold in each || Easy in-and-out fit
$14.78
04 Apr 2022
US: Florida-Parts-Z
4M8910 - Ring-RETAINING for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Compatible equipment models: 4M8910:
Information:
Mismatched or incorrect fasteners can result in damage or malfunction, or personal injury.Take care to avoid mixing metric dimensioned fasteners and inch dimensioned fasteners.
Introduction to Torque
"Torque" is measured in terms of force and distance. Force is the amount of pushing or pulling applied at the end of the lever. Distance is the length of the lever that is being used. Torque values are given in the following units: NEWTON meters (N m), pound inches (lb in), and pound feet (lb ft)This manual is intended to provide the operator with a reference. This manual will provide the standard torque settings for the following: bolts, nuts, plugs, fittings, and clamps.Exceptions to these torques are given in the Service Manual, if necessary.Be sure to use a torque wrench that has the proper range. Torque wrenches must be used properly in order to ensure that the correct torque is applied. Always use a smooth pull for torque wrenches. Do not jerk a torque wrench. Do not use adapters that change the length of the torque wrench. For the correct use of your torque wrench, refer to the instructions that were packaged with your torque wrench. For more information on the correct use of torque wrenches, refer to Special Publication, SEBV0516, "An Introduction to Torque". This publication is available on the Caterpillar Media Information Center (CMIC) and through the normal literature distribution system at your local Cat ® dealer.Prior to installation of any hardware, ensure that components are in near new condition. Bolts and threads must not be worn or damaged. Threads must not have burrs or nicks. Hardware must be free of rust and corrosion. Clean reused fasteners with a noncorrosive cleaner. Lightly lubricate the threads of reused fasteners. Lightly lubricate the mating surface of the head of reused fasteners. Other applications for lubricating fasteners may also be specified in the Service Manual. The Service Manual may also specify the use of sealants and compounds.Note: Do not use sealants that are not specified in the Service Manual. Do not use compounds that are not specified in the Service Manual. Clean old compound from the bolt and from the hole before installation.Torque-Turn
The torque-turn method is used when precise control over clamping force is required. There is an initial torque and an additional turn. The initial torque is required to bring all parts of the joint into contact. The additional turn provides the desired clamping force. Ensure that all fasteners have been torqued before you perform the additional turns. Turn the fastener according to the specified amount. The specified amount will normally be equal to or greater than 90°. The specified amount will normally be in 30° increments. Turns of 120° or 180° are preferred. Turns of 120° or 180° are easily measured by the points of the hex head of the fastener. Lubrication may be specified in order to reduce the effort that is required for the final turn. The use of the torque-turn method will allow the following:
Increase the life of the
Cat SIS web machinery list:
Parts ring Caterpillar catalog:
5P8944
RING-RETAINING
D10N, D10R, D10T, D10T2, D9L
D10N, D10R, D10T, D10T2, D9L
9W9300
RING-THRUST
D10, D10N, D10R
D10, D10N, D10R
3P6349
RING-LOCK
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
5P7151
RING-RETAINING
D11N, D11R
D11N, D11R
1513258
RING-RETAINING
D11N, D11R, D11T
D11N, D11R, D11T
7X2628
RING-RETAINING
D11N, D11R, D11T
D11N, D11R, D11T
5P4256
RING-RETAINING
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
6P7577
RING
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
3623564
RING-WEAR
D10R, D10T, D10T2
D10R, D10T, D10T2
3623565
RING-WEAR
D10R, D10T, D10T2
D10R, D10T, D10T2
2P9419
RING
345C, 345C L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, D10, D9G, D9H
345C, 345C L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, D10, D9G, D9H
3P6583
RING
D8H, D8K
D8H, D8K
9N1527
RING
7155
7155
9N1686
RING
7155
7155
9N1599
RING
7155
7155
3L5927
RING
7155, AP-600D, AP-655D, AS4252C, D320A
7155, AP-600D, AP-655D, AS4252C, D320A
9N1460
RING
7155
7155
4N7593
RING
3406, 631E, 633E II, 637D, 637E
3406, 631E, 633E II, 637D, 637E
9L0540
RING
1673
1673
9H0113
RING
1673
1673
1S9422
RING (OIL)
1693
1693
1W5432
RING-GUIDE
16G, 245, 826C, 980C
16G, 245, 826C, 980C
9N6240
RING
3306
3306
9N1984
RING
7155
7155