4S6713 RING Caterpillar parts
14E, 572G, D7G, D7G2
Rating:
Alternative (cross code) number:
CA4S6713
4S-6713
4S6713
CA4S6713
4S-6713
4S6713
Weight: 0.40 pounds 0 kg.
Information:
CONSTRUCTION TYPE
1
JOINT STYLE
GAP
MATERIAL
Gray Iron
OD
350.825
mm
THICKNESS
3.912
mm
WALL THICKNESS
5.461
mm
MOTOR GRADER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 4S6713:
Information:
Electric Power Generation AllIntroduction
Reference: Systems Operations Troubleshooting/Testing and Adjusting, UENR7097, "EMCP4.2B"Reference: Application and Installation Guide, LEBE0049, "EMCP 4.2B Generator Set Control"This Special Instruction contains necessary information for upgrading Electric Power Generator Set Control mounted panels that use the EMCP Engine Status Control (ECS), EMCP1 (per 7C-1000 Control Panel Chart), EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2B.Important Safety Information
Do not perform any procedure in this Special Instruction until you have read this Special Instruction and you understand this information. Use only proper tools and observe all precautions that pertain to the use of those tools. Failure to follow these procedures can result in personal injury. The following procedures should be observed.Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard.Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive. Ensure that any tool, procedure, work method, or operating technique you use that is not recommended by Caterpillar is safe.Ensure that the product will not be damaged or the product will not be made unsafe by the operation, lubrication, maintenance, or repair procedures used. Proper care is your responsibility.
Do not operate or work on this engine or generator set unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals.Failure to follow the warnings and instructions could result in injury or death. Contact any Caterpillar dealer for replacement manuals. Proper care is your responsibility.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Working with electrical circuits is hazardous. Bodily contact with electrical potential will cause personal injury or death. Ensure that personnel are trained in proper operating procedures in order to ensure safe operation.
Lock Out/Tag Out
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Illustration 1 g00104545Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch or to the battery disconnect
Reference: Systems Operations Troubleshooting/Testing and Adjusting, UENR7097, "EMCP4.2B"Reference: Application and Installation Guide, LEBE0049, "EMCP 4.2B Generator Set Control"This Special Instruction contains necessary information for upgrading Electric Power Generator Set Control mounted panels that use the EMCP Engine Status Control (ECS), EMCP1 (per 7C-1000 Control Panel Chart), EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2B.Important Safety Information
Do not perform any procedure in this Special Instruction until you have read this Special Instruction and you understand this information. Use only proper tools and observe all precautions that pertain to the use of those tools. Failure to follow these procedures can result in personal injury. The following procedures should be observed.Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard.Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive. Ensure that any tool, procedure, work method, or operating technique you use that is not recommended by Caterpillar is safe.Ensure that the product will not be damaged or the product will not be made unsafe by the operation, lubrication, maintenance, or repair procedures used. Proper care is your responsibility.
Do not operate or work on this engine or generator set unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals.Failure to follow the warnings and instructions could result in injury or death. Contact any Caterpillar dealer for replacement manuals. Proper care is your responsibility.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Working with electrical circuits is hazardous. Bodily contact with electrical potential will cause personal injury or death. Ensure that personnel are trained in proper operating procedures in order to ensure safe operation.
Lock Out/Tag Out
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Illustration 1 g00104545Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch or to the battery disconnect
Caterpillar parts catalog:
Parts ring Caterpillar catalog:
1S9498
RING
57, 58, 594H, 769C, 772B, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 777, 980, 980B, AD55B, AD60, D10N, D10R, D7G, D8L, D9L, D9N
57, 58, 594H, 769C, 772B, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 777, 980, 980B, AD55B, AD60, D10N, D10R, D7G, D8L, D9L, D9N
2P5804
RING
572G, D7F, D7G, D7G2
572G, D7F, D7G, D7G2
2K2578
RING
539, 572G, 594, 594H, 657B
539, 572G, 594, 594H, 657B
6V1556
RING
173B, 518, 623B, 631C, 633D, 926, 943, 953, AP-1055B, BG-2455C, D7G, G936
173B, 518, 623B, 631C, 633D, 926, 943, 953, AP-1055B, BG-2455C, D7G, G936
9T5075
RING
572G, 594H, 611, 613G, 615C, 824C, 826C, 936F, 966D, 966F, 966F II, 970F, D350E, D400E, G936, R1300, R1300G, R1300G II, R1600, R1600G, R1600H
572G, 594H, 611, 613G, 615C, 824C, 826C, 936F, 966D, 966F, 966F II, 970F, D350E, D400E, G936, R1300, R1300G, R1300G II, R1600, R1600G, R1600H
9T5087
RING
572G, 594H, 611, 613C, 613C II, 613G, 615C, 621B, 621E, 621F, 621G, 623B, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 651E, 657E, 657G, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824C, 825...
572G, 594H, 611, 613C, 613C II, 613G, 615C, 621B, 621E, 621F, 621G, 623B, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 651E, 657E, 657G, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824C, 825...
7B2499
RING-SNAP
120, 120B, 120G, 120H, 12E, 12F, 12H, 130G, 135H, 140, 140B, 140G, 140H, 140K, 14E, 16, 160H, 160K, 621, 621B, 623B, 627B, 631C, 631D, 633D, 637, 637D, 639D, 641, 641B, 650B, 651E, 657B, 657E, 657G, 6...
120, 120B, 120G, 120H, 12E, 12F, 12H, 130G, 135H, 140, 140B, 140G, 140H, 140K, 14E, 16, 160H, 160K, 621, 621B, 623B, 627B, 631C, 631D, 633D, 637, 637D, 639D, 641, 641B, 650B, 651E, 657B, 657E, 657G, 6...
9T5064
RING
528, 528B, 530B, 613C, 613C II, 613G, 926, 930R, D7G, IT28
528, 528B, 530B, 613C, 613C II, 613G, 926, 930R, D7G, IT28
6V1557
RING
613B, 631C, 920, 926, 930, D7G
613B, 631C, 920, 926, 930, D7G
4B9508
RING
120, 120B, 12E, 12F, 140B, 14E
120, 120B, 12E, 12F, 140B, 14E
1S7346
RING
14E
14E
5D3252
RING
120, 120B, 12F, 140B, 14E
120, 120B, 12F, 140B, 14E
2K2578
RING
539, 572G, 594, 594H, 657B
539, 572G, 594, 594H, 657B
5P6717
RING
561D, 572G, 583K, 594H, 977L, D5B, D6D, D7G, D8K, D9H
561D, 572G, 583K, 594H, 977L, D5B, D6D, D7G, D8K, D9H
2P5804
RING
572G, D7F, D7G, D7G2
572G, D7F, D7G, D7G2
9J9806
RING
936, 936F, 977K, 977L, 980, G936
936, 936F, 977K, 977L, 980, G936
2J8158
RING
191
191
1T1004
RING-RETAINING
910, 931, 931B, D3B, D3C II, PP120
910, 931, 931B, D3B, D3C II, PP120
5P2495
RING
528, 54, 797, 797B, 797F
528, 54, 797, 797B, 797F
3P4582
RING (internal)
528, 54
528, 54
8S5013
RING
D9G, D9H
D9G, D9H
4S8073
RING
583K, D8H, D8K
583K, D8H, D8K
6P8261
RING
D9G
D9G
6P8263
RING
651, 657, 657B, 769, 772, 834, 992, D8H, D8K, D9G
651, 657, 657B, 769, 772, 834, 992, D8H, D8K, D9G