5J0014 RING-WEAR Caterpillar parts
6A, 769, 7A, 824C, 824S, 834B, D6D, D6E, D6E SR, D6G SR, D6G2 XL, D7G
Rating:
Alternative (cross code) number:
CA5J0014
5J-0014
5J0014
CA5J0014
5J-0014
5J0014
Weight: 0.20 pounds 0 kg.
Information:
AXIAL WIDTH
31.39
mm
ID
0
mm
MATERIAL
Nylon
OD
152.4
mm
THICKNESS
3.2
mm
TYPE
PISTON
BULLDOZER, WHEEL DOZER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$16.03
02 May 2023
US: Florida-Parts-Z
5J0014 - Ring-WEAR 8M4227 5J14 for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Compatible equipment models: 5J0014:
Information:
Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     5P-3931     Anti-Seize Compound     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The alignment of the bellows is important. Improper alignment may lead to premature failure of the bellows. Misalignment can be identified by visually inspecting the convolutions for uniformity of compression.Inspect the bellows for damage prior to installation. If there is any damage to the convolutions, discard the bellows. Minor damage to the ends of the bellows may be repaired. However, if there is any difficulty in installation after the repair, discard the bellows.
Illustration 1 g01076551
Use a suitable lifting device in order to install turbocharger (16) on the exhaust manifold. The weight of the turbocharger is approximately 29 kg (65 lb).Note: Discard the locknuts after use. Use new locknuts for installation.
Apply Tooling (A) to the threads of the studs. Install locknuts (1) . Tighten the locknuts to a torque of 55 5 N m (41 4 lb ft).
Connect hose (7) .
Connect hose assembly (6) .
Connect hose assembly (15) .
Position the gasket and exhaust elbow (12) on the turbocharger. Apply Tooling (A) to the threads of the studs. Install locknuts (14) .
Position the O-ring seal and inlet elbow (13) on the turbocharger. Install clamp assembly (17) . Apply Tooling (A) to the threads of the clamp assembly and tighten to a torque of 12 4 N m (106 35 lb in).
The ends of the bellows are very sharp. Injury could occur if the bellows are not handled properly. Handle the bellows by the convolutions.
Note: Refer to Special Instruction, REHS1728, "Application Guideline for the Bellows" for additional information on handling the bellows.
Install bellows (
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     5P-3931     Anti-Seize Compound     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The alignment of the bellows is important. Improper alignment may lead to premature failure of the bellows. Misalignment can be identified by visually inspecting the convolutions for uniformity of compression.Inspect the bellows for damage prior to installation. If there is any damage to the convolutions, discard the bellows. Minor damage to the ends of the bellows may be repaired. However, if there is any difficulty in installation after the repair, discard the bellows.
Illustration 1 g01076551
Use a suitable lifting device in order to install turbocharger (16) on the exhaust manifold. The weight of the turbocharger is approximately 29 kg (65 lb).Note: Discard the locknuts after use. Use new locknuts for installation.
Apply Tooling (A) to the threads of the studs. Install locknuts (1) . Tighten the locknuts to a torque of 55 5 N m (41 4 lb ft).
Connect hose (7) .
Connect hose assembly (6) .
Connect hose assembly (15) .
Position the gasket and exhaust elbow (12) on the turbocharger. Apply Tooling (A) to the threads of the studs. Install locknuts (14) .
Position the O-ring seal and inlet elbow (13) on the turbocharger. Install clamp assembly (17) . Apply Tooling (A) to the threads of the clamp assembly and tighten to a torque of 12 4 N m (106 35 lb in).
The ends of the bellows are very sharp. Injury could occur if the bellows are not handled properly. Handle the bellows by the convolutions.
Note: Refer to Special Instruction, REHS1728, "Application Guideline for the Bellows" for additional information on handling the bellows.
Install bellows (
Caterpillar parts catalog:
Parts ring Caterpillar catalog:
8X4086
RING-LOCK
834B, 834G, 834H, 834K, 986H, 988B, 988F, 988F II, 988G, 988H, 988K
834B, 834G, 834H, 834K, 986H, 988B, 988F, 988F II, 988G, 988H, 988K
1V8578
RING-SNAP
824C, 980C, 980F, 980F II, AD40, AE40, D40D, R1700 II
824C, 980C, 980F, 980F II, AD40, AE40, D40D, R1700 II
3D2051
RING-LOCK
824C, 980, 980B, 980C, 980F, 980F II, AD40, AE40, D35C, D40D, D44B, D550B, R1700 II
824C, 980, 980B, 980C, 980F, 980F II, AD40, AE40, D35C, D40D, D44B, D550B, R1700 II
8E5268
RING-SEAL
824C, 826C, 980C
824C, 826C, 980C
1P1386
RING
769, 824B, 825B, 834, 992
769, 824B, 825B, 834, 992
3P3559
RING
824B, 824C, 980C
824B, 824C, 980C
5J6444
RING-BACKUP
515, 525, 525B, 525C, 535B, 535C, 545, 545C, 69D, 768B, 769, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM, 773, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, ...
515, 525, 525B, 525C, 535B, 535C, 545, 545C, 69D, 768B, 769, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM, 773, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, ...
8J2577
RING
769, 772, 773, 773B, 776, 777
769, 772, 773, 773B, 776, 777
8M4226
RING
769
769
9J1795
RING
769, 772, 773B, 776, 777
769, 772, 773B, 776, 777
9P3075
RING (.030 OVERSIZE)
16, 768B, 769, 772, 773
16, 768B, 769, 772, 773
8M4227
RING
769
769
8C7362
RING-RETAINING
572G, D5B, D5E, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D7G, D7G2
572G, D5B, D5E, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D7G, D7G2
9M1393
RING-SEAL
977K, 977L, D5B, D5E, D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
977K, 977L, D5B, D5E, D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
8M7438
RING-SEAL
572G, 977K, 977L, 983, 983B, D5B, D5E, D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D7F, D7G, D7G2
572G, 977K, 977L, 983, 983B, D5B, D5E, D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D7F, D7G, D7G2
4M3948
RING-SEAL
572G, 977K, 977L, 983, 983B, D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D7F, D7G, D7G2
572G, 977K, 977L, 983, 983B, D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D7F, D7G, D7G2
3P1104
RING-THRUST
955K, 955L, 963, 963B, 963C, D6C, D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL, D6H, OEMS
955K, 955L, 963, 963B, 963C, D6C, D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL, D6H, OEMS
5M7331
RING-RETAINING
613C, 613C II, 613G, 627, 936, 936F, 950B, 950B/950E, 950F, 966C, D6C, D6D, D6D SR, D6E SR, D6F SR, D6G SR, G936
613C, 613C II, 613G, 627, 936, 936F, 950B, 950B/950E, 950F, 966C, D6C, D6D, D6D SR, D6E SR, D6F SR, D6G SR, G936
1S3781
RING-RETAINING
814, 815, 950, 955K, 955L, 966C, D5, D5B, D5E
814, 815, 950, 955K, 955L, 966C, D5, D5B, D5E
1J6470
RING-RETAINING
163, 50, 561C, 910, 931, 931B, 955H, 977H, 977K, D3B, D3C II, D5, D5B, D5E
163, 50, 561C, 910, 931, 931B, 955H, 977H, 977K, D3B, D3C II, D5, D5B, D5E
4M7432
RING
561C, 977H, D5, D5B, D5E, D6E, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, RM-350B, SM-350
561C, 977H, D5, D5B, D5E, D6E, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, RM-350B, SM-350
5S9759
RING
561C, 955L, D5, D5B, D5E
561C, 955L, D5, D5B, D5E
2B8092
RING-RETAINING
561B, 561C, 561D, 977D, 977H, D5, D5B, D5E
561B, 561C, 561D, 977D, 977H, D5, D5B, D5E
9J0706
RING-RETAINING
153, 814B, 815B, 910, D4E, D4E SR, D6E SR, FB518, IT12
153, 814B, 815B, 910, D4E, D4E SR, D6E SR, FB518, IT12