5J0058 RING Caterpillar parts
824C, 824S, 834B, 834H
Rating:
Alternative (cross code) number:
CA5J0058
5J-0058
5J0058
CA5J0058
5J-0058
5J0058
Weight: 0.20 pounds 0 kg.
Information:
AXIAL WIDTH
31.39
mm
ID
0
mm
MATERIAL
Nylon
OD
165.1
mm
THICKNESS
3.2
mm
TYPE
PISTON
BULLDOZER, WHEEL DOZER,
Compare Prices:
As an associate, we earn commssions on qualifying purchases through the links below
$22.70
23 Mar 2019
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
Caterpillar Ring 5J0058 New
$12.84
19 Apr 2020
0.39[0.00] Pounds
-: -
5J0058 Ring Fits Caterpillar 836H 834S 834U 834B 834H
Warranty
Warranty
Number on catalog scheme:
25
For full view, you need register
Caterpillar parts catalog:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B - Guide Stud
1 - 14 NF by 8 inch 2
C 2D-1201 Eyebolts 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Remove the magnetic pickups.
Illustration 1 g00911678
Install Tooling (A) on flywheel (1) and attach a suitable lifting device. The weight of flywheel (1) is approximately 167 kg (370 lb).
Remove two bolts (2) from the crankshaft.
Install Tooling (B).
Remove remaining bolts (2).
Remove flywheel (1). Use the following procedure if flywheel (1) is not easily separated from the crankshaft:
Install Tooling (C) in each side of flywheel (1).
Use a prybar to remove flywheel (1) from the crankshaft. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B - Guide Stud
1 - 14 NF by 8 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Inspect the condition of the flywheel ring gear. Use the following procedure in order to replace the ring gear, if necessary.
Remove the damaged ring gear from the flywheel.
Raise the temperature of the new ring gear.
Install the gear on the flywheel. Ensure that the chamfer of the gear teeth will be toward the pinion of the starting motor.
Illustration 2 g00911678
Install Tooling (B) in the end of the crankshaft.
Install Tooling (A) onto flywheel (1) and attach a suitable lifting device. The weight of flywheel (1) is approximately 167 kg (370 lb). Note: Ensure that the mark on flywheel (1) is aligned with the mark on the crankshaft.
Lift flywheel (1) into position onto Tooling (B).
Apply clean engine oil to bolts (2) and install bolts (2).
Remove Tooling (A) and Tooling (B). Install remaining two bolts (2). Tighten bolts (2) to the correct torque. Note: Refer to Specifications, "Flywheel" for the correct torque.
Install the magnetic pickups.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B - Guide Stud
1 - 14 NF by 8 inch 2
C 2D-1201 Eyebolts 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Remove the magnetic pickups.
Illustration 1 g00911678
Install Tooling (A) on flywheel (1) and attach a suitable lifting device. The weight of flywheel (1) is approximately 167 kg (370 lb).
Remove two bolts (2) from the crankshaft.
Install Tooling (B).
Remove remaining bolts (2).
Remove flywheel (1). Use the following procedure if flywheel (1) is not easily separated from the crankshaft:
Install Tooling (C) in each side of flywheel (1).
Use a prybar to remove flywheel (1) from the crankshaft. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B - Guide Stud
1 - 14 NF by 8 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Inspect the condition of the flywheel ring gear. Use the following procedure in order to replace the ring gear, if necessary.
Remove the damaged ring gear from the flywheel.
Raise the temperature of the new ring gear.
Install the gear on the flywheel. Ensure that the chamfer of the gear teeth will be toward the pinion of the starting motor.
Illustration 2 g00911678
Install Tooling (B) in the end of the crankshaft.
Install Tooling (A) onto flywheel (1) and attach a suitable lifting device. The weight of flywheel (1) is approximately 167 kg (370 lb). Note: Ensure that the mark on flywheel (1) is aligned with the mark on the crankshaft.
Lift flywheel (1) into position onto Tooling (B).
Apply clean engine oil to bolts (2) and install bolts (2).
Remove Tooling (A) and Tooling (B). Install remaining two bolts (2). Tighten bolts (2) to the correct torque. Note: Refer to Specifications, "Flywheel" for the correct torque.
Install the magnetic pickups.
Parts ring Caterpillar catalog:
D11N, D11R
1374344
RING-TORIC
D11R, D11T
D11R, D11T
D11R, D11T
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
2462942
RING
D11R, D11T
D11R, D11T
D11N, D11R, D11T
5P1980
RING-RETAINING
D10, D11N, D11R
D10, D11N, D11R
1270319
RING-TORIC
D11N, D11R
D11N, D11R
6Y7497
RING
527, D5HTSK II
527, D5HTSK II
8E0138
RING
517, D4HTSK II, D4HTSK III
517, D4HTSK II, D4HTSK III
3176098
RING-BACKUP
814F II, 815F II, 816F II, 824H, 825H
814F II, 815F II, 816F II, 824H, 825H