5S6980 RING Caterpillar parts
621G, 623G, 627G, 631G, 637G, 657E, 657G, 725, 730, 735, 735B, 740, 740B, 814, 816, 824G II, 824H, 834G, 834H, 836G, 836H, 950, 955K, 955L, 966C, AD30, D250E II, D300E II, D350E II, D400E II, D5, D5B
Rating:
Alternative (cross code) number:
CA5S6980
5S-6980
5S6980
CA5S6980
5S-6980
5S6980
Weight: 0.01 pounds 0 kg.
Information:
OD
38.76
mm
THICKNESS
1.27
mm
TYPE
SPIRAL
ARTICULATED TRUCK, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 5S6980 Ring for Heavy Equipment
CTP Ring Only || Sold in each || Easy in-and-out fit
CTP Ring Only || Sold in each || Easy in-and-out fit
ABS Sensor Front Left 04683471AB, 04683471AC, 04683471AD, 5S6980, ABS530923
Generic High Quality Material The ABS wheel speed sensor is made of high-quality material, which is wear-resistant and durable, not easy to be damaged, and has a long service life || This wheel speed sensor is used to monitor the rotation speed of each wheel, automatically adjust the brake pump pressure, avoid individual wheels from locking, and improve the safety of the car || Superior Performance This product has excellent performance and is a perfect replacement for old or damaged products. || Easy to Install Installation can be done without too many complicated steps and tools || NOTICES:Please check picture,OE part number and FITMENT information to verify this is the correct one you need before your purchase
Generic High Quality Material The ABS wheel speed sensor is made of high-quality material, which is wear-resistant and durable, not easy to be damaged, and has a long service life || This wheel speed sensor is used to monitor the rotation speed of each wheel, automatically adjust the brake pump pressure, avoid individual wheels from locking, and improve the safety of the car || Superior Performance This product has excellent performance and is a perfect replacement for old or damaged products. || Easy to Install Installation can be done without too many complicated steps and tools || NOTICES:Please check picture,OE part number and FITMENT information to verify this is the correct one you need before your purchase
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 5S6980:
UNDERGROUND ART TRUCK
AD30
Information:
Recommendations for Lube Oils for the Power End
Caterpillar recommends the use of gear oils with extreme pressure additives for the plunger pump. In order to achieve optimum performance, follow the recommendations below.General Service Gear Oils
The use of synthetic gear oils is recommended in order to achieve optimum oil film thickness, reduced friction, improved startup of the pump and optimal wear protection. The temperature of the pump should not exceed 79° C (175° F) during use. The following characteristics are required:
Viscosity grade: 75W - 90, rated for extreme service
Viscosity Index: 135 minimum
Viscosity of 80 SUS minimum at 99° C (210° F)
Pour point: 1.7° C (35° F)
Timken test rating: 50 lbs for non-SAE grades only Alternate Seasonal Conventional (Non-Synthetic) Gear Oils
Alternate seasonal conventional (non-synthetic) gear oils can be used in the plunger pumps if both of the following conditions are met:
The oils must have an extreme pressure additive.
The oils must have a viscosity index of 93 or higher.Non-SAE grade gear oils must have a Timken test rating of 45 lbs minimum.Refer to Table 1 for the recommendations for conventional gear oils.
Table 1
Recommendations for Conventional Gear Oils
Type of Oil (1) Pour Point (Min) SUS Viscosity at
99° C (210° F) Oil Viscosity Minimum Temperature Maximum Temperature
Cat Gear Oil (GO)
API GL-5 Oils
−18° C (0° F) 85 85W - 140 (2)
0° C (32° F)
32° C (90° F)
−7° C (20° F) 124 85W - 140 (2)
4° C (40° F)
43° C (110° F)
−18° C (0° F) 75 85W - 90 (3)
−9° C (15° F)
21° C (70° F)
( 1 ) Cat oils are the preferred oils. All other commercial oils are second choice oils.
( 2 ) The operating temperature of the plunger pump must not exceed 80° C (175° F) during operation.
( 3 ) The operating temperature of the plunger pump must not exceed 54° C (130° F) during operation.Recommendations for Oil for the Fluid End
The use of an optimal plunger lubricant is critical to the achievement of full performance and service life that is designed and built into the pump. The use of the recommended oils can reduce horsepower robbing friction, reduce fuel consumption and increase the net amount of hydraulic horsepower delivered by the pump. The use of a modern machine tool Way Oil for improved lubrication of the plungers and packing is highly recommended by Caterpillar. In an area where a Way Oil is not available, a suitable Rock Drill oil may be substituted.The use of Cat HYDO Advanced oils, SAE 10 and SAE 20 are acceptable for this application.Note: The use of lubricants that do not meet these recommendations is unacceptable and may result in shorter plunger life, shorter packing life and premature failure of these components.Proper lubrication is critical during the start-up of the plunger pump. Lubricant for the plunger must begin to flow freely to the stuffing box
Caterpillar recommends the use of gear oils with extreme pressure additives for the plunger pump. In order to achieve optimum performance, follow the recommendations below.General Service Gear Oils
The use of synthetic gear oils is recommended in order to achieve optimum oil film thickness, reduced friction, improved startup of the pump and optimal wear protection. The temperature of the pump should not exceed 79° C (175° F) during use. The following characteristics are required:
Viscosity grade: 75W - 90, rated for extreme service
Viscosity Index: 135 minimum
Viscosity of 80 SUS minimum at 99° C (210° F)
Pour point: 1.7° C (35° F)
Timken test rating: 50 lbs for non-SAE grades only Alternate Seasonal Conventional (Non-Synthetic) Gear Oils
Alternate seasonal conventional (non-synthetic) gear oils can be used in the plunger pumps if both of the following conditions are met:
The oils must have an extreme pressure additive.
The oils must have a viscosity index of 93 or higher.Non-SAE grade gear oils must have a Timken test rating of 45 lbs minimum.Refer to Table 1 for the recommendations for conventional gear oils.
Table 1
Recommendations for Conventional Gear Oils
Type of Oil (1) Pour Point (Min) SUS Viscosity at
99° C (210° F) Oil Viscosity Minimum Temperature Maximum Temperature
Cat Gear Oil (GO)
API GL-5 Oils
−18° C (0° F) 85 85W - 140 (2)
0° C (32° F)
32° C (90° F)
−7° C (20° F) 124 85W - 140 (2)
4° C (40° F)
43° C (110° F)
−18° C (0° F) 75 85W - 90 (3)
−9° C (15° F)
21° C (70° F)
( 1 ) Cat oils are the preferred oils. All other commercial oils are second choice oils.
( 2 ) The operating temperature of the plunger pump must not exceed 80° C (175° F) during operation.
( 3 ) The operating temperature of the plunger pump must not exceed 54° C (130° F) during operation.Recommendations for Oil for the Fluid End
The use of an optimal plunger lubricant is critical to the achievement of full performance and service life that is designed and built into the pump. The use of the recommended oils can reduce horsepower robbing friction, reduce fuel consumption and increase the net amount of hydraulic horsepower delivered by the pump. The use of a modern machine tool Way Oil for improved lubrication of the plungers and packing is highly recommended by Caterpillar. In an area where a Way Oil is not available, a suitable Rock Drill oil may be substituted.The use of Cat HYDO Advanced oils, SAE 10 and SAE 20 are acceptable for this application.Note: The use of lubricants that do not meet these recommendations is unacceptable and may result in shorter plunger life, shorter packing life and premature failure of these components.Proper lubrication is critical during the start-up of the plunger pump. Lubricant for the plunger must begin to flow freely to the stuffing box
Cat SIS web machinery list:
Parts ring Caterpillar catalog:
814, 815, 816, 824B, 826B, 834, 950, 966C, 980, 980B, 988, 992
814, 815, 816, 824B, 826B, 834, 950, 966C, 980, 980B, 988, 992
950, 966C, D10, D11N, D11R, D11T
12E, 140M, 160M, 160M 2, 735, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 793D
120H, 120H ES, 120H NA, 120K, 120K 2, 135H, 135H NA, D10R, D10T, D10T2, D11N, D11R, D250D, D250E, D250E II, D300E, D300E II, D400E II
1390, 2590, 322B L, 325B L, 325C, 325C FM, 325C L, 325D FM, 325D FM LL, 325D MH, 330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345C, 345C L, 345C MH, 541, 541 2, 551, 552, 552 2, 568 FM LL, 725...
735, 735B, 740, 740B, D350E II, D400E II
735, 735B, 740, 740B, AD30, D350E II, D400E II
725C, 730C, 735, 735B, 740, 740B, D350E II, D400E II
725, 725C, 730
322 LN, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D FM LL, 325 LN, 325B L, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 3...
322B L, 322C FM, 325B L, 330, 330 FM L, 330 L, 330B L, 330C, 330C FM, 330C MH, 330D FM, 345B, 345B II, 345B II MH, 345B L, 345C, 350, 350 L, 568 FM LL, 834G, 834H, M325B, M330D, W330B, W345B II
561B, 561C, 977D, 977H, D5
941, 955C, 955H, D4D
120, 120G, 130G, 16, 941, 951B, 955K, 955L, D4D, D5, D5B
6B3015
RING
951B, D4D
951B, D4D
8H1319
RING
826B, 988, D4D, D8H, D8K
826B, 988, D4D, D8H, D8K
120G, 12G, 184, 641, 651, 657, 657B, 666, 824, 824B, 834, 955H, 977H, 988, 992, D5, D5B
518, 518C, 528, 528B, 530B, 735, 735B, 740, 740B, 797, 797B, 797F, 920, 930, 941, 951B, D10, D4D, D6H
518, 518C, 528, 528B, 530B, 797, 797B, 797F, 920, 930, 941, 951B, D4D
518, 528, 920, 930, 941, 951B, D4D
824B, D4D
1S7349
RING
621, 980, D4D
621, 980, D4D
5K2382
RING
941, 951B, 955H, 955K, 955L
941, 951B, 955H, 955K, 955L