6D1985 RING Caterpillar parts
650B, 69D, 768B, 769, 769C, 769D, 771C, 771D
Rating:
Alternative (cross code) number:
CA6D1985
6D-1985
6D1985
CA6D1985
6D-1985
6D1985
Weight: 0.03 pounds 0 kg.
Information:
OD
74.17
mm
THICKNESS
3.05
mm
TYPE
RECT SECT
QUARRY TRUCK, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 6D1985:
Information:
REMOVE OIL PUMP
start by:a) remove fuel transfer pump1. Drain the coolant from the cooling system.2. Drain the oil from the oil pan.3. Remove all bolts (1) and (2) to remove adapter (3) from the engine.4. Remove all the bolts and remove oil pump (4) from the engine. The weight of the pump is 39 kg (85 lb). INSTALL OIL PUMP
The oil pump shaft must turn by hand and the pump must have oil for lubrication before it is installed.1. Put clean engine oil on the O-ring seals and put oil pump (1) in position. Make sure the splines on the pump shaft are correctly engaged with the splines of the oil pump drive. Install the bolts to hold the oil pump in position.2. Put the gaskets and adapter (2) in position. Install the bolts to hold the adapter and gaskets in position.3. Fill the engine with oil to the correct level.4. Fill the cooling system with coolant to the correct level.end by:a) install fuel transfer pump DISASSEMBLE OIL PUMP
start by:a) remove oil pump The pump shown in the illustrations is for the 3508 Engine.1. Remove adapter assembly (1) from the pump.
Cover (2) has spring tension on it. Loosen the bolts that hold it slowly and the same amount to remove the tension on the cover.
2. Remove the bolts, cover (2), gasket (3), spring (4) and valve spool (5) from the pump.3. Remove cover assembly (6) and the gasket from the pump.4. Remove cover assembly (7) from the pump. 5. Use tooling (A) to remove bearings (8) from cover assembly (7).6. Remove shaft assemblies (10) from body assembly (9).7. Use a press to remove gears (11) from the shaft assemblies.8. Use tooling (A) to remove bearings (12) from body assembly (9). ASSEMBLE OIL PUMP
The pump shown in the illustration is for the 3508 Engine.1. Make an alignment of bearings (1) so the joints are 45 15° from a line through the center of the bearing bores as shown.2. Use tooling (A) to install bearings (1) in the body assembly until they are 1.5 0.5 mm (.059 0.20 in) below the gear bore in the body assembly. Check the inside diameter of the bearings after installation. The diameter must be 31.837 0.070 mm (1.2534 .0028 in).3. Heat gears (2) to a maximum temperature of 316° C (600° F).4. Install the gears on shaft assemblies (3) until they are 34.0 0.5 mm (1.34 .020 in) from the cover end of the shaft assemblies to the face of the gears and 47.0 0.5 mm (1.85 .020 in) from the fuel pump drive end of shaft assembly (4).5. Install shaft assemblies (3) and (4) in the body assembly. 6. Make sure dowels (5) and (8) are installed in cover assembly (6) so they extend 6 0.5 mm (.236 .02 in) above the surface of the cover assembly.7. Use tooling (A) and install bearings (7) in cover assembly (6) with
start by:a) remove fuel transfer pump1. Drain the coolant from the cooling system.2. Drain the oil from the oil pan.3. Remove all bolts (1) and (2) to remove adapter (3) from the engine.4. Remove all the bolts and remove oil pump (4) from the engine. The weight of the pump is 39 kg (85 lb). INSTALL OIL PUMP
The oil pump shaft must turn by hand and the pump must have oil for lubrication before it is installed.1. Put clean engine oil on the O-ring seals and put oil pump (1) in position. Make sure the splines on the pump shaft are correctly engaged with the splines of the oil pump drive. Install the bolts to hold the oil pump in position.2. Put the gaskets and adapter (2) in position. Install the bolts to hold the adapter and gaskets in position.3. Fill the engine with oil to the correct level.4. Fill the cooling system with coolant to the correct level.end by:a) install fuel transfer pump DISASSEMBLE OIL PUMP
start by:a) remove oil pump The pump shown in the illustrations is for the 3508 Engine.1. Remove adapter assembly (1) from the pump.
Cover (2) has spring tension on it. Loosen the bolts that hold it slowly and the same amount to remove the tension on the cover.
2. Remove the bolts, cover (2), gasket (3), spring (4) and valve spool (5) from the pump.3. Remove cover assembly (6) and the gasket from the pump.4. Remove cover assembly (7) from the pump. 5. Use tooling (A) to remove bearings (8) from cover assembly (7).6. Remove shaft assemblies (10) from body assembly (9).7. Use a press to remove gears (11) from the shaft assemblies.8. Use tooling (A) to remove bearings (12) from body assembly (9). ASSEMBLE OIL PUMP
The pump shown in the illustration is for the 3508 Engine.1. Make an alignment of bearings (1) so the joints are 45 15° from a line through the center of the bearing bores as shown.2. Use tooling (A) to install bearings (1) in the body assembly until they are 1.5 0.5 mm (.059 0.20 in) below the gear bore in the body assembly. Check the inside diameter of the bearings after installation. The diameter must be 31.837 0.070 mm (1.2534 .0028 in).3. Heat gears (2) to a maximum temperature of 316° C (600° F).4. Install the gears on shaft assemblies (3) until they are 34.0 0.5 mm (1.34 .020 in) from the cover end of the shaft assemblies to the face of the gears and 47.0 0.5 mm (1.85 .020 in) from the fuel pump drive end of shaft assembly (4).5. Install shaft assemblies (3) and (4) in the body assembly. 6. Make sure dowels (5) and (8) are installed in cover assembly (6) so they extend 6 0.5 mm (.236 .02 in) above the surface of the cover assembly.7. Use tooling (A) and install bearings (7) in cover assembly (6) with
Caterpillar parts catalog:
Parts ring Caterpillar catalog:
9X7304
RING-SEAL
69D, 769C, 769D, 771C, 771D
69D, 769C, 769D, 771C, 771D
6G1732
RING-LOCK
69D, 768C, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM, AD55, AD55B, AD60, R2900G, R3000H
69D, 768C, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM, AD55, AD55B, AD60, R2900G, R3000H
8T7693
RING
69D, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM
69D, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM
3G3470
RING-WEAR
69D, 769C, 769D, 770G, 770G OEM, 771C, 771D, 772G, 772G OEM, 795F AC, 795F XQ, 797F
69D, 769C, 769D, 770G, 770G OEM, 771C, 771D, 772G, 772G OEM, 795F AC, 795F XQ, 797F
3402373
RING-RETAINING
769C, 769D, 770G, 770G OEM, 771C, 771D, 772G, 772G OEM
769C, 769D, 770G, 770G OEM, 771C, 771D, 772G, 772G OEM
7J3300
RING-WEAR
69D, 769C, 769D, 771C, 771D, 773
69D, 769C, 769D, 771C, 771D, 773
8J2577
RING
769, 772, 773, 773B, 776, 777
769, 772, 773, 773B, 776, 777
8M4226
RING
769
769
6J3075
RING
769
769
9J1795
RING
769, 772, 773B, 776, 777
769, 772, 773B, 776, 777
9P3075
RING (.030 OVERSIZE)
16, 768B, 769, 772, 773
16, 768B, 769, 772, 773
1T1355
RING
769C, 772B, 773B, 785, D35HP, D400
769C, 772B, 773B, 785, D35HP, D400
3S0108
RING ASSEM.
621, 631C
621, 631C
3S0114
RING
621, 631C, 657B
621, 631C, 657B
2S0028
RING
621, 623, 627, 631C, 657B
621, 623, 627, 631C, 657B
3S0092
RING ASSEM.
621, 623, 627, 631C, 657B
621, 623, 627, 631C, 657B
3D2325
RING
621, 623, 627
621, 623, 627
5S7053
RING
5230B, 621, 621B, 621R, 623, 623B, 627B, 631C, 633C, 633D, 637D, 641B, 650B, 769C, 777
5230B, 621, 621B, 621R, 623, 623B, 627B, 631C, 633C, 633D, 637D, 641B, 650B, 769C, 777
3D9931
RING
650B, 666
650B, 666
4D4432
RING
650B, 666, 666B
650B, 666, 666B
3S2920
RING
650B, 657, 769, 834, D9G
650B, 657, 769, 834, D9G
5K0926
RING
518, 930, 930R
518, 930, 930R
2M4479
RING
641, 651, 657, 657B, 666, 834, 992
641, 651, 657, 657B, 666, 834, 992
2D5272
RING
16, 613, 613B, 650B, 666, 769, 814B, 930, 936, 950, 950B, 950B/950E, 950F, 950F II, 950G, 960F, 962G, 966C, 966D, 966F, 980B, AP-1000B, AP-600D, AP-800C, AP-800D, AP-900B, AP1000E, BG-225B, BG-260D, B...
16, 613, 613B, 650B, 666, 769, 814B, 930, 936, 950, 950B, 950B/950E, 950F, 950F II, 950G, 960F, 962G, 966C, 966D, 966F, 980B, AP-1000B, AP-600D, AP-800C, AP-800D, AP-900B, AP1000E, BG-225B, BG-260D, B...