6H8146 RING Caterpillar parts
834B, 963, 980C, 988B, 988F, 988F II, D353C, D3B, D3C, D4H, D4HTSK II, D5B, D5H, D5HTSK II, D7G, D8K, D9E, D9H
Rating:
Alternative (cross code) number:
CA6H8146
6H-8146
6H8146
CA6H8146
6H-8146
6H8146
Weight: 0.05 pounds 0 kg.
Information:
MARINE USAGE
N
MAXIMUM EFFECTIVE DIAMETER
38.1
mm
MINIMUM EFFECTIVE DIAMETER
20.57
mm
THUMB SCREW ADJ
N
WITH INNER LINER
N
INDUSTRIAL ENGINE, WHEEL LOADER,
Compatible equipment models: 6H8146:
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Start By:
Release the system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all lines, on all hoses, on all wires and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This will help to prevent fluid loss and this will help to keep contaminants from entering the system.
Drain the oil from the hydraulic tank for the implement and the braking system into a suitable container. The capacity of the implement and braking hydraulic tank is 173 L (45 US gal).
Illustration 1 g00884807
Remove guard (1) from tilt cylinder (2) .
Illustration 2 g00884810
Disconnect hydraulic hose assemblies (3) from tilt cylinder (2) .
Illustration 3 g00884811
Fasten a suitable lifting sling and a suitable hoist to cylinder (2) .Note: The blade can move rearward when you remove pin (6) or pin (7). In order to prevent injury, block the blade or support the blade with a suitable hoist and a suitable chain.
Remove bolts (4), retainer (5), and pin (6) .
Remove pin (7) .
Illustration 4 g00884812
Carefully remove tilt cylinder (2). The weight of the cylinder is 239 kg (525 lb).
Repeat steps 2 through 7 for the tilt cylinder of the opposite machine side.
Start By:
Release the system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all lines, on all hoses, on all wires and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This will help to prevent fluid loss and this will help to keep contaminants from entering the system.
Drain the oil from the hydraulic tank for the implement and the braking system into a suitable container. The capacity of the implement and braking hydraulic tank is 173 L (45 US gal).
Illustration 1 g00884807
Remove guard (1) from tilt cylinder (2) .
Illustration 2 g00884810
Disconnect hydraulic hose assemblies (3) from tilt cylinder (2) .
Illustration 3 g00884811
Fasten a suitable lifting sling and a suitable hoist to cylinder (2) .Note: The blade can move rearward when you remove pin (6) or pin (7). In order to prevent injury, block the blade or support the blade with a suitable hoist and a suitable chain.
Remove bolts (4), retainer (5), and pin (6) .
Remove pin (7) .
Illustration 4 g00884812
Carefully remove tilt cylinder (2). The weight of the cylinder is 239 kg (525 lb).
Repeat steps 2 through 7 for the tilt cylinder of the opposite machine side.
Caterpillar parts catalog:
Parts ring Caterpillar catalog:
3L1523
RING
D353C
D353C
2L4683
RING
D342, D342C, D353C, D398
D342, D342C, D353C, D398
5B1978
RING
D342, D342C, D8H
D342, D342C, D8H
2F8983
RING
D342, D353C
D342, D353C
9F9733
RING
D342, D353C
D342, D353C
9F9623
RING
D342, D353C
D342, D353C
8H2440
RING
D353C
D353C
5H4908
RING
583H, D353C, D9E
583H, D353C, D9E
1L7104
RING
D343
D343
D353C
4H9941
RING
D353C, D9E
D353C, D9E
D353C