6P7985 RING-SEAL Caterpillar parts
517, 527, 561M, 561N, 589, 613C, 613C II, 613G, 735, 735B, 740, 740B, 785, 936, 936F, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966H, 966K, 966M...
Rating:
Alternative (cross code) number:
CA6P7985
6P-7985
6P7985
CA6P7985
6P-7985
6P7985
Weight: 0.03 pounds 0 kg.
Information:
AXIAL WIDTH
3.91
mm
END CLEARANCE
2.24
mm
GAGE DIAMETER
160
mm
MATERIAL
Plastic
RADIAL WIDTH
3.56
mm
ARTICULATED TRUCK, WHEEL TRACTOR-SCRAPER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$40.37
31 Jan 2024
US: FinditParts Inc
6P7985 - RING-SEAL fits Caterpillar (CAT)
BLUMAQ 6P7985 - RING-SEAL fits Caterpillar (CAT)
BLUMAQ 6P7985 - RING-SEAL fits Caterpillar (CAT)
This part in 5 request:
Show.
This information for suppliers only!
2024-12-16
2022-09-26
2022-07-11
2022-07-11
2019-04-30
Compatible equipment models: 6P7985:
Information:
Disassembly Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1P-2320     Combination Puller     1    
B     1U-5429     Snap Ring Pliers     1    Start By:
Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump - Remove".Note: Use 8T-0447 Dial Calipers to measure the dimensions in the following procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00618774
Loosen bolt (2) and use Tooling (A) in order to separate gear (1) from the pump shaft.
Remove bolt (2), the washer, and gear (1) from the pump shaft.
Remove the O-ring seal from the fuel transfer pump.
Illustration 2 g00618775
Put an alignment mark across the sections of the fuel transfer pump. This is done in order to maintain alignment when the pump is assembled.
Remove bolts (3) that hold the fuel transfer pump together, but do not separate the components at this time.
Position the fuel transfer pump on the end of relief valve. This is the flat end.
Illustration 3 g00618778
Carefully lift front housing (4) off the dowels. Ensure that front housing (4) is oriented straight when front housing (4) is being lifted.
Illustration 4 g00618780
Inspect bearing (5) in front housing (4). The inside diameter of a new bearing (5) must be 15.951 mm (0.6280 inch).
If bearing (5) is worn or damaged, replacement of front housing (4) is necessary.
Turn over the front housing.
Illustration 5 g00618781
Remove O-ring seal (7) from front housing (4) .Note: Seal seat (6) has an O-ring seal which gives resistance to movement.
Remove seal seat (6). Seal seat (6) has an O-ring seal around the outside. Be careful not to damage front housing (4) while seal seat (6) is being removed.
Illustration 6 g00618783
Remove lip seal (8) from front housing (4). Be careful not to damage front housing (4) while the lip seal is being removed.
Illustration 7 g00618785
Personal injury can result from parts and/or covers under spring pressure.Spring force will be released when covers are removed.Be prepared to hold spring loaded covers as the bolts are loosened.
Remove carbon face seal (9). The seal components are shown in the inset. Seal seat (6) was previously removed from the front housing.
Illustration 8 g00622500
Use Tooling (B) in order to remove retaining ring (11) .
Remove dowels (10) .
Carefully lift middle housing (12) off the dowels. Ensure that middle housing (12) is oriented straight when middle housing (12) is being lifted.
Illustration 9 g00618788
Remove O-ring seal (13) .
Remove check valves (14) from middle housing (12) .
Inspect bearings (15) in middle housing (12). The inside diameter of new bearings (15) must be 15.951 mm (0.6280 inch).
If bearings (15) are worn or damaged, replacement of middle housing (12) is necessary.
Illustration 10 g00618789
Remove dowels (17) .
Remove gear cases (16) .
Inspect the gear cases for wear. Also ensure that the gear cases are not damaged.
Illustration 11 g00618790
Remove shaft assembly (18) and shaft assembly (19) .
Inspect the shaft assemblies for wear. Ensure that the shaft assemblies are not damaged. The shaft diameter of a new shaft should be 15.869 0.006 mm (0.6248
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1P-2320     Combination Puller     1    
B     1U-5429     Snap Ring Pliers     1    Start By:
Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump - Remove".Note: Use 8T-0447 Dial Calipers to measure the dimensions in the following procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00618774
Loosen bolt (2) and use Tooling (A) in order to separate gear (1) from the pump shaft.
Remove bolt (2), the washer, and gear (1) from the pump shaft.
Remove the O-ring seal from the fuel transfer pump.
Illustration 2 g00618775
Put an alignment mark across the sections of the fuel transfer pump. This is done in order to maintain alignment when the pump is assembled.
Remove bolts (3) that hold the fuel transfer pump together, but do not separate the components at this time.
Position the fuel transfer pump on the end of relief valve. This is the flat end.
Illustration 3 g00618778
Carefully lift front housing (4) off the dowels. Ensure that front housing (4) is oriented straight when front housing (4) is being lifted.
Illustration 4 g00618780
Inspect bearing (5) in front housing (4). The inside diameter of a new bearing (5) must be 15.951 mm (0.6280 inch).
If bearing (5) is worn or damaged, replacement of front housing (4) is necessary.
Turn over the front housing.
Illustration 5 g00618781
Remove O-ring seal (7) from front housing (4) .Note: Seal seat (6) has an O-ring seal which gives resistance to movement.
Remove seal seat (6). Seal seat (6) has an O-ring seal around the outside. Be careful not to damage front housing (4) while seal seat (6) is being removed.
Illustration 6 g00618783
Remove lip seal (8) from front housing (4). Be careful not to damage front housing (4) while the lip seal is being removed.
Illustration 7 g00618785
Personal injury can result from parts and/or covers under spring pressure.Spring force will be released when covers are removed.Be prepared to hold spring loaded covers as the bolts are loosened.
Remove carbon face seal (9). The seal components are shown in the inset. Seal seat (6) was previously removed from the front housing.
Illustration 8 g00622500
Use Tooling (B) in order to remove retaining ring (11) .
Remove dowels (10) .
Carefully lift middle housing (12) off the dowels. Ensure that middle housing (12) is oriented straight when middle housing (12) is being lifted.
Illustration 9 g00618788
Remove O-ring seal (13) .
Remove check valves (14) from middle housing (12) .
Inspect bearings (15) in middle housing (12). The inside diameter of new bearings (15) must be 15.951 mm (0.6280 inch).
If bearings (15) are worn or damaged, replacement of middle housing (12) is necessary.
Illustration 10 g00618789
Remove dowels (17) .
Remove gear cases (16) .
Inspect the gear cases for wear. Also ensure that the gear cases are not damaged.
Illustration 11 g00618790
Remove shaft assembly (18) and shaft assembly (19) .
Inspect the shaft assemblies for wear. Ensure that the shaft assemblies are not damaged. The shaft diameter of a new shaft should be 15.869 0.006 mm (0.6248
Cat SIS web machinery list:
Parts ring Caterpillar catalog:
0855593
RING-RETAINING
320 L, 320B, 320B L, 320N, 345B, 345B L, 785, 785B, 785C, 789B, 789C, 793B, CB-534B, CB-534C, CB-634, CB-634C, CP-433C, CS-431C, E70B, OEMS
320 L, 320B, 320B L, 320N, 345B, 345B L, 785, 785B, 785C, 789B, 789C, 793B, CB-534B, CB-534C, CB-634, CB-634C, CP-433C, CS-431C, E70B, OEMS
4T4804
RING-BACKUP
785, 789, 789B, 789C, 789D
785, 789, 789B, 789C, 789D
1982643
RING-BACKUP
1390, 2590, 322B L, 325B L, 325C, 325C FM, 325C L, 325D FM, 325D FM LL, 325D MH, 330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345C, 345C L, 345C MH, 541, 541 2, 551, 552, 552 2, 568 FM LL, 725...
1390, 2590, 322B L, 325B L, 325C, 325C FM, 325C L, 325D FM, 325D FM LL, 325D MH, 330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345C, 345C L, 345C MH, 541, 541 2, 551, 552, 552 2, 568 FM LL, 725...
1378116
RING-SEAL
735, 735B, 740, 740B, D350E II, D400E II
735, 735B, 740, 740B, D350E II, D400E II
1378118
RING-SEAL
735, 735B, 740, 740B, AD30, D350E II, D400E II
735, 735B, 740, 740B, AD30, D350E II, D400E II
1550385
RING-CLAMP
725C, 730C, 735, 735B, 740, 740B, D350E II, D400E II
725C, 730C, 735, 735B, 740, 740B, D350E II, D400E II
1T1355
RING
769C, 772B, 773B, 785, D35HP, D400
769C, 772B, 773B, 785, D35HP, D400
6J1973
RING-EXPANDER
R1300
R1300
6Y0471
RING-RETAINING
5110B, D10N, D10R, D10T, D10T2
5110B, D10N, D10R, D10T, D10T2
3K8692
RING-BACKUP
518, 518C, 844, 844H, 844K, 854G, 854K, D10N, D11N, D11R, D11T, D4HTSK II, D4HTSK III, D5HTSK II, D8R, D8R II, D8T, D9N, D9R, D9T
518, 518C, 844, 844H, 844K, 854G, 854K, D10N, D11N, D11R, D11T, D4HTSK II, D4HTSK III, D5HTSK II, D8R, D8R II, D8T, D9N, D9R, D9T
1317184
RING-WEAR
D8L, D9N, D9R, D9T
D8L, D9N, D9R, D9T
5P8944
RING-RETAINING
D10N, D10R, D10T, D10T2, D9L
D10N, D10R, D10T, D10T2, D9L
9M1503
RING-METAL SEAL
14E, 517, 527, 561M, 561N, 572G, 589, 613C, 613C II, 613G, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637B, 637D, 637E, 637G, 641B, 650B, 651E, 657E, 657G, 69D, 735, 735B, 740, 740B, 768C, 769...
14E, 517, 527, 561M, 561N, 572G, 589, 613C, 613C II, 613G, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637B, 637D, 637E, 637G, 641B, 650B, 651E, 657E, 657G, 69D, 735, 735B, 740, 740B, 768C, 769...
5M6187
RING-METAL SEAL
589, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 980C, 980F, 980F II, 980G, 980G II, 980H, 980K, 980K HL...
589, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 980C, 980F, 980F II, 980G, 980G II, 980H, 980K, 980K HL...
6F0156
RING-METAL SEAL
24H, 24M, 589, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 910, 916, 926, 926A, 931B, 931C, 931C II, 933...
24H, 24M, 589, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 910, 916, 926, 926A, 931B, 931C, 931C II, 933...
8K2692
RING-RETAINING
24H, 24M, 515, 518C, 525, 528B, 530B, 589, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 844, 844H, 844K, 854G, 854K, 980C, 980F, 980F II, 980G, 980G II,...
24H, 24M, 515, 518C, 525, 528B, 530B, 589, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 844, 844H, 844K, 854G, 854K, 980C, 980F, 980F II, 980G, 980G II,...
6V0836
RING-RETAINING
24H, 24M, 589, 613C, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 82...
24H, 24M, 589, 613C, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 82...
8T1141
RING-RETAINING
24H, 24M, 589, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 980C, 980F, 980F II, 980G, 980G II, 980H, 980...
24H, 24M, 589, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 980C, 980F, 980F II, 980G, 980G II, 980H, 980...
2M3974
RING-RETAINING
120G, 12G, 130G, 140G, 14E, 14G, 14H NA, 160G, 16G, 16H NA, 528, 572G, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 589, 621, 623, 641B, 651E, 657B, 657E, 657G, 910, 931B, 977K, D10N, D10R, D10T, D10T2...
120G, 12G, 130G, 140G, 14E, 14G, 14H NA, 160G, 16G, 16H NA, 528, 572G, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 589, 621, 623, 641B, 651E, 657B, 657E, 657G, 910, 931B, 977K, D10N, D10R, D10T, D10T2...
7J6525
RING-RETAINING
589, 613, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 836, 950, 980C, 980F, 980F II, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, 983B, 988B,...
589, 613, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 836, 950, 980C, 980F, 980F II, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, 983B, 988B,...
9W6991
RING-SEAL
589, 785, 789, 797, 797B, 797F, 994, 994D, 994F, 994H, D10N, D10R, D10T, D10T2, D8L, D9N, D9R, D9T
589, 785, 789, 797, 797B, 797F, 994, 994D, 994F, 994H, D10N, D10R, D10T, D10T2, D8L, D9N, D9R, D9T
1082735
RING-LOCK
589, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 980F, 980F II, 980G, 980G II, 980H, 980K, 980K HLG, 980...
589, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 980F, 980F II, 980G, 980G II, 980H, 980K, 980K HLG, 980...
5P3150
RING-RETAINING
589, D10N, D8L, D9L, D9N, D9R, D9T
589, D10N, D8L, D9L, D9N, D9R, D9T
5P3119
RING-RETAINING
2470C, 24H, 24M, 2570C, 2670C, 2864C, 508, 517, 525B, 525C, 525D, 533, 535B, 535C, 535D, 543, 545, 545C, 545D, 553C, 555D, 563C, 573C, 586C, 589, 910, 916, 926, 931B, 931C, 931C II, 933, 938H, 939, 95...
2470C, 24H, 24M, 2570C, 2670C, 2864C, 508, 517, 525B, 525C, 525D, 533, 535B, 535C, 535D, 543, 545, 545C, 545D, 553C, 555D, 563C, 573C, 586C, 589, 910, 916, 926, 931B, 931C, 931C II, 933, 938H, 939, 95...