7X6719 RING Caterpillar parts
AP-1000, AP-1050, AP-1200, AP-800, RM-350B
Rating:
Alternative (cross code) number:
CA7X6719
7X-6719
7X6719
CA7X6719
7X-6719
7X6719
Weight: 0.01 pounds 0 kg.
ASPHALT PAVER, ROAD RECLAIMER,
Compatible equipment models: 7X6719:
Number on catalog scheme:
28
For full view, you need register
Information:
Starting the ATS System
To start the ATS instrument, and connect the ATS instrument to the system, complete the following steps:
Illustration 1 g01780449
From any guidance screen, press "ATS". The ATS start-up dialog appears. The dialog below is used to start an SPS730 or SPS930 Advanced Tracking Station (ATS).
For SPS730 and SPS930 instruments only, set the Target ID. To do this, complete the following steps:
Illustration 2 g01780448
Press the "Target ID" softkey. The "MT900 Target ID" dialog appears:
Enter the selected "Target ID" into the "Target ID:" field. By convention, target IDs of 9 through 16 are used for machine control applications. IDs of 1 through 8 are reserved for surveying applications. Ask your site manager which target ID you should use. To set the default value of 9, press the "Default" softkey.
To confirm the settings, press the "OK" key. Press the Escape key in order to exit without saving changes.The ATS start-up dialog appears.
Set the "Auto search" status as required.If "Auto search" is turned on (Yes) and the ATS loses lock on the target, the ATS will automatically attempt to locate and lock onto the target again by searching the area that is bounded by the search window defined during ATS set up.If "Auto search" is turned off and the ATS loses lock, refer to the information for reaquiring a lock in Operation and Maintenance Manual, SEBU8501, "Setting Up For Operation".
Illustration 3 g01780447
Press "Start".The ATS system starts and the ATS instrument automatically searches for the target in the area bounded by the search window defined during ATS set up.When the target is acquired, the ATS dialog changes to the "Tracking" layout as shown above.Note: If the ATS takes too long to find the target, press the Escape key in order to stop the search and the start-up of the ATS.Some common ATS set up problems are as follows.
Table 1
Problem Action
No Start softkey in ATS dialog. The machine data radio has not synchronized with the ATS instrument data radio. Refer to Operation and Maintenance Manual, SEBU8501, "Diagnostics - View (ATS)".
Check that the ATS instrument data radio is turned on.
Check the instrument battery.
ATS fails to start Ask your site manager to check that the radio channel, and network if applicable, set up in the control box is compatible with the instrument radio. Refer to Operation and Maintenance Manual, SEBU8501, "Diagnostics - View (ATS)". Selecting A Bucket
Use the following steps in order to access the "Bucket Selection" dialog:
From any guidance screen, press the Menu button.The "Setup Menu - Configuration" screen appears.
Select "Select Bucket".The "Bucket Selection" dialog appears.Setting The Accuracy Level
The system provides an interface that allows you to change the accuracy of the ATS data that is required to estimate the orientation of the machine. Occasionally it may be difficult to get an orientation estimate. For example, if the ATS instrument is operating at the limit of its range, or if the machine is rocking a lot. In these cases, if high accuracy guidance information is not required you
To start the ATS instrument, and connect the ATS instrument to the system, complete the following steps:
Illustration 1 g01780449
From any guidance screen, press "ATS". The ATS start-up dialog appears. The dialog below is used to start an SPS730 or SPS930 Advanced Tracking Station (ATS).
For SPS730 and SPS930 instruments only, set the Target ID. To do this, complete the following steps:
Illustration 2 g01780448
Press the "Target ID" softkey. The "MT900 Target ID" dialog appears:
Enter the selected "Target ID" into the "Target ID:" field. By convention, target IDs of 9 through 16 are used for machine control applications. IDs of 1 through 8 are reserved for surveying applications. Ask your site manager which target ID you should use. To set the default value of 9, press the "Default" softkey.
To confirm the settings, press the "OK" key. Press the Escape key in order to exit without saving changes.The ATS start-up dialog appears.
Set the "Auto search" status as required.If "Auto search" is turned on (Yes) and the ATS loses lock on the target, the ATS will automatically attempt to locate and lock onto the target again by searching the area that is bounded by the search window defined during ATS set up.If "Auto search" is turned off and the ATS loses lock, refer to the information for reaquiring a lock in Operation and Maintenance Manual, SEBU8501, "Setting Up For Operation".
Illustration 3 g01780447
Press "Start".The ATS system starts and the ATS instrument automatically searches for the target in the area bounded by the search window defined during ATS set up.When the target is acquired, the ATS dialog changes to the "Tracking" layout as shown above.Note: If the ATS takes too long to find the target, press the Escape key in order to stop the search and the start-up of the ATS.Some common ATS set up problems are as follows.
Table 1
Problem Action
No Start softkey in ATS dialog. The machine data radio has not synchronized with the ATS instrument data radio. Refer to Operation and Maintenance Manual, SEBU8501, "Diagnostics - View (ATS)".
Check that the ATS instrument data radio is turned on.
Check the instrument battery.
ATS fails to start Ask your site manager to check that the radio channel, and network if applicable, set up in the control box is compatible with the instrument radio. Refer to Operation and Maintenance Manual, SEBU8501, "Diagnostics - View (ATS)". Selecting A Bucket
Use the following steps in order to access the "Bucket Selection" dialog:
From any guidance screen, press the Menu button.The "Setup Menu - Configuration" screen appears.
Select "Select Bucket".The "Bucket Selection" dialog appears.Setting The Accuracy Level
The system provides an interface that allows you to change the accuracy of the ATS data that is required to estimate the orientation of the machine. Occasionally it may be difficult to get an orientation estimate. For example, if the ATS instrument is operating at the limit of its range, or if the machine is rocking a lot. In these cases, if high accuracy guidance information is not required you
Caterpillar parts catalog:
Parts ring Caterpillar catalog:
6R1765
RING-RETAINING
AP-1000, AP-1050, AP-800
AP-1000, AP-1050, AP-800
7X5446
RING-RETAINING
AP-1000, AP-1050, AP-1200, AP-800, AP-800C, AP-800D, AP-900B, BG-225B, CB-434, CP-433B, CP-433C, CP-563, CS-431B, CS-431C, CS-433C, CS-531, CS-531C, CS-533, CS-533C, CS-563C, CS-583
AP-1000, AP-1050, AP-1200, AP-800, AP-800C, AP-800D, AP-900B, BG-225B, CB-434, CP-433B, CP-433C, CP-563, CS-431B, CS-431C, CS-433C, CS-531, CS-531C, CS-533, CS-533C, CS-563C, CS-583
7X5454
RING-BACKUP
AP-1000, AP-1050, AP-1200, AP-800, AP-800C, AP-800D, AP-900B, BG-225B, CB-434, CP-433B, CP-433C, CP-563, CS-431B, CS-431C, CS-433C, CS-531, CS-531C, CS-533, CS-533C, CS-563C, CS-583
AP-1000, AP-1050, AP-1200, AP-800, AP-800C, AP-800D, AP-900B, BG-225B, CB-434, CP-433B, CP-433C, CP-563, CS-431B, CS-431C, CS-433C, CS-531, CS-531C, CS-533, CS-533C, CS-563C, CS-583
7X5469
RING-RETAINING
AP-1000, AP-1000B, AP-1050, AP-1055B, AP-1055D, AP-1200, AP-200B, AP-600D, AP-655C, AP-655D, AP-800, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455C, BG-2455D, BG-245C,...
AP-1000, AP-1000B, AP-1050, AP-1055B, AP-1055D, AP-1200, AP-200B, AP-600D, AP-655C, AP-655D, AP-800, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455C, BG-2455D, BG-245C,...
5E9849
RING AS
AP-1000, AP-1050, BG-225C
AP-1000, AP-1050, BG-225C
5E8580
RING-RETAINING
AP-1000, AP-1000B, AP-1050, AP-1200, AP-600D, AP-650B, AP-655C, AP-655D, AP-800, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-245C, BG1000E, BG1055E, BG500E, BG600D, BG655...
AP-1000, AP-1000B, AP-1050, AP-1200, AP-600D, AP-650B, AP-655C, AP-655D, AP-800, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-245C, BG1000E, BG1055E, BG500E, BG600D, BG655...
0779687
RING-RETAINING
AP-1000, AP-1000B, AP-1050, AP-1055B, AP-800, AP-800C, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C
AP-1000, AP-1000B, AP-1050, AP-1055B, AP-800, AP-800C, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C
1C4651
RING-SNAP
AP-1050, AP-1200, AP-800
AP-1050, AP-1200, AP-800
8C0445
RING-SQUARE
AP-1000, AP-1000B, AP-1050, AP-1055B, AP-200B, AP-650B, AP-800, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C
AP-1000, AP-1000B, AP-1050, AP-1055B, AP-200B, AP-650B, AP-800, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C
0817511
RING
AP-1050, AP-1055B, AP-1055D, AP-650B, AP-655C, AP-655D, AP1055E, AP555E, BG-225C, BG-2455C, BG-2455D, BG-245C, BG1055E, BG655D
AP-1050, AP-1055B, AP-1055D, AP-650B, AP-655C, AP-655D, AP1055E, AP555E, BG-225C, BG-2455C, BG-2455D, BG-245C, BG1055E, BG655D
5E8745
RING-PISTON
AP-1000, AP-1000B, AP-1050, AP-650B, AP-800C, AP-800D, BG-225B, BG-225C, BG-245C, CB-434, CP-563, CS-531, CS-531C, CS-533C, CS-563C, CS-573C, CS-583C, RM-250C, RR-250B
AP-1000, AP-1000B, AP-1050, AP-650B, AP-800C, AP-800D, BG-225B, BG-225C, BG-245C, CB-434, CP-563, CS-531, CS-531C, CS-533C, CS-563C, CS-573C, CS-583C, RM-250C, RR-250B
5E8778
RING
AP-1000, AP-1000B, AP-1050, AP-650B, AP-800C, AP-800D, BG-225B, BG-225C, BG-245C, CB-434, CB-534B, CB-534C, CB-535B, CB-634, CB-634C, CP-563, RR-250, SS-250
AP-1000, AP-1000B, AP-1050, AP-650B, AP-800C, AP-800D, BG-225B, BG-225C, BG-245C, CB-434, CB-534B, CB-534C, CB-535B, CB-634, CB-634C, CP-563, RR-250, SS-250