8I0837 RING-SEAL Caterpillar parts
AP-1000B, AP-1055B, AP-650B, AP-800C, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C
Rating:
Alternative (cross code) number:
CA8I0837
8I-0837
8I0837
CA8I0837
8I-0837
8I0837
Weight: 9 pounds 4 kg.
ASPHALT PAVER,
Compatible equipment models: 8I0837:
Number on catalog scheme:
26
For full view, you need register
Information:
Removal Procedure
Always rotate the jaw set so that the jaw being worked on is positioned on the bottom. Parts must be lifted and removed from lower jaw. Parts are heavy and will fall if removed from upper jaw.Crush injury. Could cause serious injury or death.
Personal injury or death can result from sudden work tool movement.Sudden movement of the work tool can cause injury to persons near the work tool.To prevent injury or death, make sure that the area around the work tool is clear of personnel and obstructions before operating the work tool.
Illustration 1 g03416996
Place the work tool in a horizontal position. Open the jaw of the work tool.
Close the ball valves on the host machine to lock the moveable jaw in the open position.
Illustration 2 g03430558
Typical Example
Remove bolts (2), shims (3), and cutting edge (1). Discard bolts (2). Repeat procedure for the remaining cutting edges. Installation Procedure
Note: Thoroughly clean all contact surfaces before installing the new cutters. Remove any rust, paint, nicks, and burrs from the surfaces.
Illustration 3 g03430558
Install shim (3) measuring 2.00 mm (0.079 inch) behind cutting edge (1) on one side of the jaw. Install the cutting edge on the opposite jaw without any shims. Install bolts (2) and tighten to a torque of 520 70 N m (384 52 lb ft).
Open the ball valves on the host machine to unlock the moveable jaw. Slowly close the jaws on the work tool.
Measure the clearance between the cutting edge of the moveable jaw and the cutting edge of the fixed jaw. The clearance between the cutting edges must be less than 0.5 mm (0.02 inch). Note: On the shear jaw sets, the clearance between the guide blade and cutter of the fixed jaw must also be checked.Note: The cutting edge and guide blades must be in front of the base material in order to reduce the wear of the base material.
Loosen bolts (2) and remove the cutting edge that was installed without any shims.
Install shims (3) necessary to achieve the required amount of clearance between the cutting edges on the fixed jaw and the moveable jaw. Reinstall the cutting edge.
Install new bolts (2) and tighten to a torque of 520 70 N m (384 52 lb ft).
Always rotate the jaw set so that the jaw being worked on is positioned on the bottom. Parts must be lifted and removed from lower jaw. Parts are heavy and will fall if removed from upper jaw.Crush injury. Could cause serious injury or death.
Personal injury or death can result from sudden work tool movement.Sudden movement of the work tool can cause injury to persons near the work tool.To prevent injury or death, make sure that the area around the work tool is clear of personnel and obstructions before operating the work tool.
Illustration 1 g03416996
Place the work tool in a horizontal position. Open the jaw of the work tool.
Close the ball valves on the host machine to lock the moveable jaw in the open position.
Illustration 2 g03430558
Typical Example
Remove bolts (2), shims (3), and cutting edge (1). Discard bolts (2). Repeat procedure for the remaining cutting edges. Installation Procedure
Note: Thoroughly clean all contact surfaces before installing the new cutters. Remove any rust, paint, nicks, and burrs from the surfaces.
Illustration 3 g03430558
Install shim (3) measuring 2.00 mm (0.079 inch) behind cutting edge (1) on one side of the jaw. Install the cutting edge on the opposite jaw without any shims. Install bolts (2) and tighten to a torque of 520 70 N m (384 52 lb ft).
Open the ball valves on the host machine to unlock the moveable jaw. Slowly close the jaws on the work tool.
Measure the clearance between the cutting edge of the moveable jaw and the cutting edge of the fixed jaw. The clearance between the cutting edges must be less than 0.5 mm (0.02 inch). Note: On the shear jaw sets, the clearance between the guide blade and cutter of the fixed jaw must also be checked.Note: The cutting edge and guide blades must be in front of the base material in order to reduce the wear of the base material.
Loosen bolts (2) and remove the cutting edge that was installed without any shims.
Install shims (3) necessary to achieve the required amount of clearance between the cutting edges on the fixed jaw and the moveable jaw. Reinstall the cutting edge.
Install new bolts (2) and tighten to a torque of 520 70 N m (384 52 lb ft).
Caterpillar parts catalog:
Parts ring Caterpillar catalog:
2483211
RING-RETAINING
AP-1000B, AP-1055B, AP-1055D, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, RM-300
AP-1000B, AP-1055B, AP-1055D, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, RM-300
2400773
RING-RETAINING
AP-1000B, AP-1055B, AP-1055D, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, CB-434D, CB-534D, CB-54, CB-64, CP-56, CP-573E, CP-64, CP-76, CS-533E, CS-54, CS-56, CS-...
AP-1000B, AP-1055B, AP-1055D, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, CB-434D, CB-534D, CB-54, CB-64, CP-56, CP-573E, CP-64, CP-76, CS-533E, CS-54, CS-56, CS-...
1831245
RING-WEAR
10 FT, 10B, 8 FT, AP-800C, BG-225B, BG-2455C
10 FT, 10B, 8 FT, AP-800C, BG-225B, BG-2455C
1795936
RING-WEAR
AP-1000B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-245C
AP-1000B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-245C
1139950
RING
AP-800C, BG-225B, BG-245C
AP-800C, BG-225B, BG-245C
1139946
RING
AP-800C, BG-225B, BG-245C
AP-800C, BG-225B, BG-245C
0687248
RING-SNAP
508, RM-350B, SM-350
508, RM-350B, SM-350
0652746
RING-BEARING
M325B, RM-250C, RR-250, RR-250B, SM-350, SS-250
M325B, RM-250C, RR-250, RR-250B, SM-350, SS-250
1118067
RING-BACKUP
SM-350
SM-350
1118058
RING-ADJUSTMENT
SM-350
SM-350
0067006
RING
M325B, RM-250C, RM-350B, RR-250, RR-250B, SM-350, SS-250
M325B, RM-250C, RM-350B, RR-250, RR-250B, SM-350, SS-250
1627564
RING-RETAINING
AP-800C, AP-800D, BG-225B
AP-800C, AP-800D, BG-225B