AVSPARE.COM
parts catalog

RIPPER AS. 3236935 - Caterpillar



3236935 RIPPER AS. Caterpillar parts RIPPER
Rating:
76
Alternative (cross code) number:
CA3236935
323-6935
3236935
Caterpillar 3236935 RIPPER AS.

Buy RIPPER AS. 3236935 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Remove the cap from charge pressure tap (14) on the left propel pump. Connect second Tool (A2) to the pressure tap.Note: The right and left propulsion systems share a common charge pressure tap on the left propel pump.Test Procedure
Charge Relief Test Procedure
Move machine power switch (10) to the ON position.
Press push to start switch (7) for 2 seconds to start the engine. An LED next to the push to start switch will flash when the engine is in start mode. When the engine has started, the LED will remain illuminated.Note: Only one attempt to start the engine is allowed per key cycle. A new key cycle is necessary to restart the process.
Operate the engine at low idle for a few minutes.
Illustration 13 g06091258
Press rpm increase switch (16) on the throttle control to place the engine in high idle. The engine speed should increase to 2200 rpm.
Monitor the hydraulic oil temperature on operator display (15). Operate the machine until the oil temperature reaches 43 5.6 °C (110 10 °F).
Record the pressure at charge pressure tap (14). The charge pressure should be 2425 175 kPa (352 25 psi).
Record the pressure at case drain tap (13). The case drain pressure should be 175 kPa (25 psi) to 410 kPa (59 psi).
Subtract the pressure that was recorded in Step 7 from the pressure that was recorded in Step 6. The differential pressure should be 1950 kPa (283 psi) to 2500 kPa (363 psi).
Press rpm decrease switch (9) for the throttle control once to operate the engine in low idle.
Shut off the engine. Either place machine power switch (10) in the OFF position or press and hold push to start switch (7) for 3 seconds. An LED next to the push to start switch will flash when the engine is in shutdown mode.
If the push to start switch (7) was used to shut off the engine, move machine power switch (10) to the OFF position.
If the pressure is within the specified range, go to Flushing Valve Test Procedure. If the pressure is not within the specified range, go to "Charge Relief Adjustment Procedure", Step 1.Flushing Valve Test Procedure
Move machine power switch (10) to the ON position.
Press push to start switch (7) for 2 seconds to start the engine. An LED next to the push to start switch will flash when the engine is in start mode. When the engine has started, the LED will remain illuminated.Note: Only one attempt to start the engine is allowed per key cycle. A new key cycle is necessary to restart the process.
Illustration 14 g06091258
Press rpm increase switch (16) on the throttle control to place the engine in high idle. The engine speed should increase to 2200 rpm.
Monitor the hydraulic oil temperature on operator display (15). Operate the machine until the oil temperature reaches 43 5.6 °C (110 10 °F).
Operate the engine at low idle for a few minutes.
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause


Parts ripper Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.