4T4501 RIPPER TIP-375 MM (14.7 IN.) LONG Caterpillar parts
329D L, 345C, 345C L, 345D L, 375, D10, D10N, D9R, D9T
Rating:
Alternative (cross code) number:
CA4T4501
4T-4501
4T4501
CA4T4501
4T-4501
4T4501
Weight: 60 pounds 27 kg.
EXCAVATOR, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$155.77
24 Nov 2023
Amazon.com
CTP 4T4501 Tip for Ground Engagement Tools
CTP For Ground Engagement Tools || Sold in each || Easy in-and-out fit
CTP For Ground Engagement Tools || Sold in each || Easy in-and-out fit
$156.89
12 Oct 2023
Amazon.com
CTP 4T4501 Tip for Ground Engagement Tools
CTP For Ground Engagement Tools || Sold in each || Easy in-and-out fit
CTP For Ground Engagement Tools || Sold in each || Easy in-and-out fit
$173.35
24 Jul 2023
Amazon.com
CTP 4T4501 Tip for Ground Engagement Tools
CTP For Ground Engagement Tools || Sold in each || Easy in-and-out fit
CTP For Ground Engagement Tools || Sold in each || Easy in-and-out fit
Number on catalog scheme:
2
For full view, you need register
4T4501
Images:
Compatible equipment models: 4T4501:
Information:
Removal Procedure
Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Illustration 1 g01336497
Use an allen wrench to loosen cap (1). Carefully remove cap (1) from the housing of engine oil pump (4). Note: The spring force will be released when the cap is removed.
Remove spring (2) from the bore for the relief valve in the housing of engine oil pump (4).
Use long nose pliers to remove plunger (3) from the bore for the relief valve in the housing of engine oil pump (4). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 577 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01336497
Ensure that all components are clean and free from wear or damage. If necessary, replace any components that are worn or damaged. If the bore for the relief valve in the housing of engine oil pump (4) is worn or damaged, the complete assembly of the engine oil pump must be replaced.
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Lubricate plunger (3) with clean engine oil. Use long nose pliers to install plunger (3) and spring (2) into the bore for the relief valve in the housing of engine oil pump (4). Note: The plunger must slide freely in the bore for the relief valve.
Apply Tooling (A) to the threads of cap (1). Use an allen wrench to install cap (1) to engine oil pump (4). Tighten the cap to a torque of 21 N m (15.5 lb ft). Note: Ensure that the spring is properly located inside the plunger and the cap. Ensure that Tooling (A) does not contaminate the bore for the relief valve in the housing of the engine oil pump.End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install".
Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Illustration 1 g01336497
Use an allen wrench to loosen cap (1). Carefully remove cap (1) from the housing of engine oil pump (4). Note: The spring force will be released when the cap is removed.
Remove spring (2) from the bore for the relief valve in the housing of engine oil pump (4).
Use long nose pliers to remove plunger (3) from the bore for the relief valve in the housing of engine oil pump (4). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 577 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01336497
Ensure that all components are clean and free from wear or damage. If necessary, replace any components that are worn or damaged. If the bore for the relief valve in the housing of engine oil pump (4) is worn or damaged, the complete assembly of the engine oil pump must be replaced.
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Lubricate plunger (3) with clean engine oil. Use long nose pliers to install plunger (3) and spring (2) into the bore for the relief valve in the housing of engine oil pump (4). Note: The plunger must slide freely in the bore for the relief valve.
Apply Tooling (A) to the threads of cap (1). Use an allen wrench to install cap (1) to engine oil pump (4). Tighten the cap to a torque of 21 N m (15.5 lb ft). Note: Ensure that the spring is properly located inside the plunger and the cap. Ensure that Tooling (A) does not contaminate the bore for the relief valve in the housing of the engine oil pump.End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install".
Caterpillar parts catalog:
Parts ripper Caterpillar catalog:
9C7516
RIPPER AS
227
227
8R4551
RIPPER AS
235C, 235D
235C, 235D
5Y0793
RIPPER AR
D8L
D8L
5Y0795
RIPPER AR
D8L
D8L
5A6881
RIPPER ARRANGEMENT
Caterpillar
Caterpillar
