1140475 ROD AS Caterpillar parts
315, 317
Rating:
Alternative (cross code) number:
CA1140475
114-0475
1140475
CA1140475
114-0475
1140475
Weight: 165 pounds 74 kg.
Information:
ROD DIAMETER
84.93
mm
ROD END TYPE
BOLT
ROD EYE TYPE
1
ROD LENGTH
1762.5
mm
EXCAVATOR,
Number on catalog scheme:
23
For full view, you need register
Information:
Probable Causes
Diagnostic codes
ECM parameters
Air intake and exhaust system
Fuel supply
Individual malfunctioning cylinders
Electronic unit injectorsRecommended Actions
Diagnostic Codes
Check for active diagnostic codes on the electronic service tool. Troubleshoot any active codes before continuing with this procedure.ECM Parameters
Ensure that the fault is not a programmed parameter.
Ensure that the correct mode was selected by using the electronic service tool.
Use the electronic service tool to verify the correct engine rating for the engine.
Use the electronic service tool to verify the maximum engine speed limit.
Use the electronic service tool to verify the following parameters at maximum speed: the boost pressure, the smoke limit, the torque limit and the amount of fuel that is delivered.
Use the electronic service tool to reset the parameters to the OEM specifications.
Ensure that the repairs have eliminated the fault.
If the repairs have not eliminated the fault proceed to "Air Intake and Exhaust System". Air Intake and Exhaust System
Check the air filter restriction indicator, if equipped.
Ensure that the air filter is clean and serviceable.
Check the air intake and the exhaust system for the following defects:
Blockages
Restrictions
Damage to the air intake and exhaust lines and hoses
Make all necessary repairs to the engine.
Ensure that the repairs have eliminated the fault.
If the fault has not been eliminated, proceed to "Fuel Supply". Fuel Supply
Visually check the fuel tank for fuel. The fuel gauge may be faulty.
Ensure that the fuel supply valve is in the full OPEN position.
If the temperature is below 0 °C (32 °F), check for solidified fuel (wax).
Visually inspect the fuel supply lines for restrictions.
Check that the low pressure fuel lines are tight and secured properly.
Remove the fuel filters. Inspect the fuel filters for contamination. Install new fuel filters. Refer to the Operation and Maintenance Manual, "Fuel System Filter- Replace and Fuel System Primary Filter (Water Separator) Element - Replace". Determine the cause of the contamination.
Check the diesel fuel for contamination. Refer to Systems Operation, Testing and Adjusting, "Fuel Quality - Test".
Check for air in the low pressure fuel system. Refer to Systems Operation, Testing and Adjusting, "Air in Fuel - Test".
Ensure that the fuel system has been primed. Refer to Systems Operation, Testing and Adjusting, "Fuel System - Prime".
Check the fuel pressure. Refer to Systems Operation, Testing and Adjusting, "Fuel System Pressure - Test".
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Contact with high pressure fuel may cause personal injury or death. Wait 60 seconds after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines.
If the high pressure fuel lines have a leak, the high pressure fuel lines must be replaced. Refer to Disassembly and Assembly, "Fuel injection lines - Remove and Fuel injection lines - Install".
If the repairs do not eliminate the fault proceed to "Individual Malfunctioning Cylinders". Individual Malfunctioning Cylinders
With the engine speed at a fast idle, use the electronic service tool
Diagnostic codes
ECM parameters
Air intake and exhaust system
Fuel supply
Individual malfunctioning cylinders
Electronic unit injectorsRecommended Actions
Diagnostic Codes
Check for active diagnostic codes on the electronic service tool. Troubleshoot any active codes before continuing with this procedure.ECM Parameters
Ensure that the fault is not a programmed parameter.
Ensure that the correct mode was selected by using the electronic service tool.
Use the electronic service tool to verify the correct engine rating for the engine.
Use the electronic service tool to verify the maximum engine speed limit.
Use the electronic service tool to verify the following parameters at maximum speed: the boost pressure, the smoke limit, the torque limit and the amount of fuel that is delivered.
Use the electronic service tool to reset the parameters to the OEM specifications.
Ensure that the repairs have eliminated the fault.
If the repairs have not eliminated the fault proceed to "Air Intake and Exhaust System". Air Intake and Exhaust System
Check the air filter restriction indicator, if equipped.
Ensure that the air filter is clean and serviceable.
Check the air intake and the exhaust system for the following defects:
Blockages
Restrictions
Damage to the air intake and exhaust lines and hoses
Make all necessary repairs to the engine.
Ensure that the repairs have eliminated the fault.
If the fault has not been eliminated, proceed to "Fuel Supply". Fuel Supply
Visually check the fuel tank for fuel. The fuel gauge may be faulty.
Ensure that the fuel supply valve is in the full OPEN position.
If the temperature is below 0 °C (32 °F), check for solidified fuel (wax).
Visually inspect the fuel supply lines for restrictions.
Check that the low pressure fuel lines are tight and secured properly.
Remove the fuel filters. Inspect the fuel filters for contamination. Install new fuel filters. Refer to the Operation and Maintenance Manual, "Fuel System Filter- Replace and Fuel System Primary Filter (Water Separator) Element - Replace". Determine the cause of the contamination.
Check the diesel fuel for contamination. Refer to Systems Operation, Testing and Adjusting, "Fuel Quality - Test".
Check for air in the low pressure fuel system. Refer to Systems Operation, Testing and Adjusting, "Air in Fuel - Test".
Ensure that the fuel system has been primed. Refer to Systems Operation, Testing and Adjusting, "Fuel System - Prime".
Check the fuel pressure. Refer to Systems Operation, Testing and Adjusting, "Fuel System Pressure - Test".
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Contact with high pressure fuel may cause personal injury or death. Wait 60 seconds after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines.
If the high pressure fuel lines have a leak, the high pressure fuel lines must be replaced. Refer to Disassembly and Assembly, "Fuel injection lines - Remove and Fuel injection lines - Install".
If the repairs do not eliminate the fault proceed to "Individual Malfunctioning Cylinders". Individual Malfunctioning Cylinders
With the engine speed at a fast idle, use the electronic service tool
Caterpillar parts catalog:
Parts rod Caterpillar catalog:
212, 224, 3054, 3056, 312, 315, 317, 416B, 416C, 426B, 426C, 428, 428B, 428C, 436C, 438C, AP-800, AP-800C, BG-225B, CB-534B, CB-534C, CB-535B, CP-433C, CS-431C, PS-200B, PS-300B, RT50, TH103, TH62, TH...
206, 212, 214, 3054, 3054B, 3054C, 3054E, 3056, 3056E, 307, 312, 312B L, 312C, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 315, 315B L, 315C, 317, 318D2 L, 320D2, 320D2 GC, 320D2 L, 414E, 416B, 416C, ...
1140, 1673C, 1693, 3126B, 315, 315B L, 317, 3176B, 3176C, 3196, 3208, 320C, 3306, 3306C, 3406, 3406E, 3408, 3456, 571G, 572G, 572R, 611, 613B, 613C, 615, 615C, 637D, 65, 65C, 65E, 75, 75C, 75D, 75E, 7...
311, 311B, 312, 312B, 315, 315B, 315B L, 315C, 317, 320 L, OEMS
8U4048
ROD-CYLINDER
213B, 214B, 224B, 312, 312B L, 315, 317
213B, 214B, 224B, 312, 312B L, 315, 317
307, 307B, 311, 311B, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322B L, 322B LN, 322C, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 L, 330B L, 345B, 345B II, 345B L, 350, 350 L, 375, 37...
1107278
ROD AS
312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322 LN, 322B LN, 325B L, M312, M315
312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322 LN, 322B LN, 325B L, M312, M315
1025673
ROD
305.5, 306, 307, 307B, 307C, 307D, 311, 311B, 311C, 312, 312B, 312B L, 315, 315B, 315B L, 317, 317B LN, 318B, 320B U, 320C
305.5, 306, 307, 307B, 307C, 307D, 311, 311B, 311C, 312, 312B, 312B L, 315, 315B, 315B L, 317, 317B LN, 318B, 320B U, 320C
307, 308E SR, 312, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 317, 320 L, 322, 322 FM L, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, 350, 350 L, 375, 375 L, 5080, 5130, 5130B, 5230, 5230B, 525B, 5...
1122089
ROD-CONNECTING
312, 315, 317, 322 FM L, 325 L, 330, 330 L, 350, 375, 375 L, 5080
312, 315, 317, 322 FM L, 325 L, 330, 330 L, 350, 375, 375 L, 5080
1122090
ROD-CONNECTING
312, 315, 317, 322 FM L, 325 L, 330, 330 L, 350, 375, 375 L, 5080
312, 315, 317, 322 FM L, 325 L, 330, 330 L, 350, 375, 375 L, 5080
6C9024
ROD
312, 315, 317, 322 FM L, 325 L, 330, 330 L, 350, 375, 375 L, 5080
312, 315, 317, 322 FM L, 325 L, 330, 330 L, 350, 375, 375 L, 5080
1276061
ROD AS
315, 317
315, 317
1276057
ROD AS
315, 317
315, 317
1076646
ROD AS
315, 317
315, 317
1057389
ROD AS
315, 317
315, 317
1276048
ROD AS
315, 317
315, 317
1057343
ROD AS
315, 317
315, 317
2160590
ROD AS
M312, M313C, M315, M315C, M316C, M318, M318C
M312, M313C, M315, M315C, M316C, M318, M318C
206, 206B, 212, 212B, M312, M313C, M315, M315C, M316C, M318
1233886
ROD END
M318, M320
M318, M320
1233885
ROD END
M312, M315, M318, M320
M312, M315, M318, M320
1128089
ROD
M318, M320
M318, M320
1276053
ROD AS
315, 317
315, 317