1772575 ROD AS Caterpillar parts
320C, 320C FM, 320C L, 321C
Rating:
Alternative (cross code) number:
CA1772575
177-2575
1772575
CA1772575
177-2575
1772575
Weight: 120 pounds 54 kg.
Information:
ROD DIAMETER
85
mm
ROD END TYPE
NUT
ROD EYE TYPE
2
ROD LENGTH
1652
mm
EXCAVATOR,
Related part:
1772575
ROD AS-HYD-YM
4950123
CL
Number on catalog scheme:
11
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools for Engines with Rear Gear Train
Tool Part Number Part Description Qty
A 5P-7301 Locator 1
5P-7309 Bolt 2
5P-7310 Bolt 2
8T-2683 Seal Installer 1
9S-8858 Nut 1
Required Tools for Engines without Rear Gear Train
Tool Part Number Part Description Qty
B 5P-1733 Locator 1
5P-1737 Bolt 3
6V-6143 Seal Installer 1
9S-8858 Nut 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Once the seal and the wear sleeve are separated, these components cannot be used again. Refer to Special Instruction, SMHS8508, "Special Handling Information and Installation Instructions for Crankshaft Seal Groups that Have Hydrodynamic Grooves In the Sealing Lip" before the seal is serviced.Note: Do not use any type of lubricant during the installation of the crankshaft seal and the wear sleeve.Note: Before you install the wear sleeve, inspect the crankshaft for scratches or any distortion on the surface of the crankshaft that may lead to an out of round condition. Use a polishing cloth and remove any imperfections on the crankshaft.
Illustration 1 g00477681
Install crankshaft rear seal (6) and wear sleeve (1) with Tool (A) or Tool (B), as follows:
Illustration 2 g00582512
Typical example
Use 169-5464 Quick Cure Primer to clean the outside diameter of crankshaft (3) and the inside diameter of wear sleeve (1).
Apply 4C-9507 Retaining Compound to the outside diameter of crankshaft (3). Apply 4C-9507 Retaining Compound to the inside diameter of wear sleeve (1).
Put locator (2) in position on crankshaft (3). Install the bolts (7) that hold the locator in position on the crankshaft.
Illustration 3 g00565570
Typical example
Install wear sleeve (1) and seal (6) on crankshaft (3). Put installer (4) on locator (2).
Illustration 4 g00565576
Typical example
Lubricate the face of nut (5). Install nut (5) on locator (4).
Tighten nut (5) until installer (4) contacts locator (2).
Remove Tool (A) or (B) and check the crankshaft seal and the wear sleeve for the correct installation. End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Table 1
Required Tools for Engines with Rear Gear Train
Tool Part Number Part Description Qty
A 5P-7301 Locator 1
5P-7309 Bolt 2
5P-7310 Bolt 2
8T-2683 Seal Installer 1
9S-8858 Nut 1
Required Tools for Engines without Rear Gear Train
Tool Part Number Part Description Qty
B 5P-1733 Locator 1
5P-1737 Bolt 3
6V-6143 Seal Installer 1
9S-8858 Nut 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Once the seal and the wear sleeve are separated, these components cannot be used again. Refer to Special Instruction, SMHS8508, "Special Handling Information and Installation Instructions for Crankshaft Seal Groups that Have Hydrodynamic Grooves In the Sealing Lip" before the seal is serviced.Note: Do not use any type of lubricant during the installation of the crankshaft seal and the wear sleeve.Note: Before you install the wear sleeve, inspect the crankshaft for scratches or any distortion on the surface of the crankshaft that may lead to an out of round condition. Use a polishing cloth and remove any imperfections on the crankshaft.
Illustration 1 g00477681
Install crankshaft rear seal (6) and wear sleeve (1) with Tool (A) or Tool (B), as follows:
Illustration 2 g00582512
Typical example
Use 169-5464 Quick Cure Primer to clean the outside diameter of crankshaft (3) and the inside diameter of wear sleeve (1).
Apply 4C-9507 Retaining Compound to the outside diameter of crankshaft (3). Apply 4C-9507 Retaining Compound to the inside diameter of wear sleeve (1).
Put locator (2) in position on crankshaft (3). Install the bolts (7) that hold the locator in position on the crankshaft.
Illustration 3 g00565570
Typical example
Install wear sleeve (1) and seal (6) on crankshaft (3). Put installer (4) on locator (2).
Illustration 4 g00565576
Typical example
Lubricate the face of nut (5). Install nut (5) on locator (4).
Tighten nut (5) until installer (4) contacts locator (2).
Remove Tool (A) or (B) and check the crankshaft seal and the wear sleeve for the correct installation. End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Caterpillar parts catalog:
Parts rod Caterpillar catalog:
307C, 308C, 311, 311B, 311C, 311D LRR, 311F LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E ...
315B FM L, 315C, 317B LN, 318B, 318C, 319C, 320 L, 320B, 320C, 320N, OEMS
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
318C, 320C, 320C L, 321C
318C, 320C, 320C FM, 320C L, 321B, 321C, 322C, 325C L, 330D L
318C, 319C, 320B, 320C, 322C, 325B L, 325C, 325D, 330B L, 330C, 345B II, 345B L
320C, 320C FM, 322C FM, 325C
320C, 320C FM, 320C L, 321C
320C, 323D L, 325D, 325D FM, 325D L, 329D L, 329D LN
2931792
ROD AS
321C
321C
2449317
ROD AS
321C
321C
1980675
ROD
320C
320C
2487250
ROD
320C, 320C FM
320C, 320C FM
1948321
ROD AS
320C, 325C, 325C FM
320C, 325C, 325C FM
1702135
ROD
320C, 325B L, 325D L, 330C, 345B II, MP15, VT50
320C, 325B L, 325D L, 330C, 345B II, MP15, VT50
320C, 325C
320C, 320C FM, 322C FM, 325C
1614956
ROD END
574
574
2897831
ROD & BEARING AS-CYLINDER
320C, 325C
320C, 325C
320C, 320C FM, 320C L, 321C
1772613
ROD AS
320C, 322C
320C, 322C
1850225
ROD AS
320C
320C
1850198
ROD AS
320C, 325C, 330C L
320C, 325C, 330C L
1772610
ROD AS
320C
320C