1884185 ROD AS Caterpillar parts
322C
Rating:
Alternative (cross code) number:
CA1884185
188-4185
1884185
CA1884185
188-4185
1884185
Weight: 321 pounds 145 kg.
Information:
ROD DIAMETER
100
mm
ROD END TYPE
NUT
ROD EYE TYPE
1
ROD LENGTH
2141
mm
EXCAVATOR,
Compatible equipment models: 1884185:
Number on catalog scheme:
11
For full view, you need register
Information:
This diagnostic code is recorded when the brake ECM receives information about the harness code from another ECM. The information that was received is NOT correct.Note: Other related diagnostic codes may cause this diagnostic code. Check for other related diagnostic codes.Test Step 1. VERIFY THE HARDWARE AND THE SOFTWARE PART NUMBERS
Verify whether the following part numbers are correct:
Software part number for the tractor's power train ECM
Software part number for the monitoring systemExpected Result:Consult the Business Unit that is producing the product for the correct configuration for the machine.Results:
OK - All part numbers are correct. Proceed to test step 2.
NOT OK - All of the part numbers are NOT correct. Repair: One of the modules that are listed above may have the wrong part number and/or the software configuration is NOT correct. See Testing And Adjusting, "Electronic Control Module (ECM) - Flash Program".STOPTest Step 2. INSPECT THE HARNESS CONNECTIONS.
Turn the key start switch and the disconnect switch to the OFF position.
Inspect the harness connections that are related to the CAT data link. Make sure that the connectors are clean and tight.
Check the mating of the connector.
Check the wires at the connector.
Check each wire for nicks and/or signs of abrasion in the insulation.
Check for moisture at the connector.
Check for dirty contacts and/or corroded contacts.
Check each pin and check each socket. Expected Result:The machine harness connectors are tight and free of corrosion.Results:
OK - The machine harness connectors are tight and the connectors are free of corrosion. Proceed to test step 3.
NOT OK - The machine harness connectors require repair. Repair: Repair the harness or replace the harness. STOPTest Step 3. CHECK FOR ADDITIONAL RELATED DIAGNOSTIC CODES.
Ensure that all electronic control modules that use the CAT data link are connected.
Turn the disconnect switch and the key start switch to the ON position.
Acknowledge any active diagnostic codes that are currently displayed on the message center.
Verify that NO related diagnostic codes are present. Expected Result:NO other diagnostic codes are present. Results:
OK - NO other related diagnostic codes are present. Proceed to test step 4.
NOT OK - Other related diagnostic codes are present.Repair: Exit this procedure and perform the other related diagnostic codes. Verify that the other related diagnostic codes are NOT present. Observe the status of the CID 0967 FMI 09. If the CID 0967 FMI 09 remains active, perform CID 0967 FMI 09 again. STOPTest Step 4. CHECK FOR SHORTS TO GROUND
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness from all electronic control modules that use the CAT data link.
At the machine harness, measure the resistance between J1-9 and frame ground. Expected Result:The resistance is greater than 5000 ohms.Results:
OK - The resistance is greater than 5000 ohms. The harness circuit is correct. Proceed to test step 5.
NOT OK - The resistance is NOT greater than 5000 ohms. The machine harness has failed.Repair: There is a short between frame ground and the data link circuit in the machine harness. Repair the machine harness or replace
Verify whether the following part numbers are correct:
Software part number for the tractor's power train ECM
Software part number for the monitoring systemExpected Result:Consult the Business Unit that is producing the product for the correct configuration for the machine.Results:
OK - All part numbers are correct. Proceed to test step 2.
NOT OK - All of the part numbers are NOT correct. Repair: One of the modules that are listed above may have the wrong part number and/or the software configuration is NOT correct. See Testing And Adjusting, "Electronic Control Module (ECM) - Flash Program".STOPTest Step 2. INSPECT THE HARNESS CONNECTIONS.
Turn the key start switch and the disconnect switch to the OFF position.
Inspect the harness connections that are related to the CAT data link. Make sure that the connectors are clean and tight.
Check the mating of the connector.
Check the wires at the connector.
Check each wire for nicks and/or signs of abrasion in the insulation.
Check for moisture at the connector.
Check for dirty contacts and/or corroded contacts.
Check each pin and check each socket. Expected Result:The machine harness connectors are tight and free of corrosion.Results:
OK - The machine harness connectors are tight and the connectors are free of corrosion. Proceed to test step 3.
NOT OK - The machine harness connectors require repair. Repair: Repair the harness or replace the harness. STOPTest Step 3. CHECK FOR ADDITIONAL RELATED DIAGNOSTIC CODES.
Ensure that all electronic control modules that use the CAT data link are connected.
Turn the disconnect switch and the key start switch to the ON position.
Acknowledge any active diagnostic codes that are currently displayed on the message center.
Verify that NO related diagnostic codes are present. Expected Result:NO other diagnostic codes are present. Results:
OK - NO other related diagnostic codes are present. Proceed to test step 4.
NOT OK - Other related diagnostic codes are present.Repair: Exit this procedure and perform the other related diagnostic codes. Verify that the other related diagnostic codes are NOT present. Observe the status of the CID 0967 FMI 09. If the CID 0967 FMI 09 remains active, perform CID 0967 FMI 09 again. STOPTest Step 4. CHECK FOR SHORTS TO GROUND
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness from all electronic control modules that use the CAT data link.
At the machine harness, measure the resistance between J1-9 and frame ground. Expected Result:The resistance is greater than 5000 ohms.Results:
OK - The resistance is greater than 5000 ohms. The harness circuit is correct. Proceed to test step 5.
NOT OK - The resistance is NOT greater than 5000 ohms. The machine harness has failed.Repair: There is a short between frame ground and the data link circuit in the machine harness. Repair the machine harness or replace
Caterpillar parts catalog:
Parts rod Caterpillar catalog:
120H, 120H ES, 120H NA, 135H, 135H NA, 211B, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322 LN, 322B L, 322B LN, 322C, 322C FM, 325, 325 L, 325 LN, 325B, 325B L, 325C, 35, 446B, 45, 525...
120H, 120H ES, 120H NA, 135H, 135H NA, 211B, 214B, 3114, 3116, 3126, 320B, 322B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 35, 446B, 446D, 45, 525B, 533, 535B, 539, 543, 55, 550, 561M, 570, 5...
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 12M, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 160K, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 3...
120H, 120K, 120K 2, 12H, 12K, 12M, 135H, 140G, 140K, 140K 2, 140M, 140M 2, 160K, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 3126, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D ...
307, 307B, 311, 311B, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322B L, 322B LN, 322C, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 L, 330B L, 345B, 345B II, 345B L, 350, 350 L, 375, 37...
307C, 308C, 311, 311B, 311C, 311D LRR, 311F LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E ...
318C, 320C, 320C FM, 320C L, 321B, 321C, 322C, 325C L, 330D L
318C, 319C, 320B, 320C, 322C, 325B L, 325C, 325D, 330B L, 330C, 345B II, 345B L
322B L, 322C, 325B L, 325C, 325C FM, 325D FM, 325D FM LL, 330B L, 330C, 330C FM, 330C L, 330D FM, 385B, 385C L, 568 FM LL, M325B
322B, 322B LN, 322C, 325, 325 L, 325 LN, 325B, 325B L, 325C, 330, 330B, 330B L, 330C, 330C FM, 330C L, 385B
322C
3699601
ROD AS
322C, 324D, 324D L, 324E, 324E L, 324E LN, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN
322C, 324D, 324D L, 324E, 324E L, 324E LN, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN
1884187
ROD AS
322C
322C
1884180
ROD AS
322C
322C
322C
2149191
ROD AS
525B
525B
1998061
ROD
525B
525B
2366941
ROD AS
525B, 535B
525B, 535B
1336834
ROD AS
320B FM LL, 320C FM
320B FM LL, 320C FM
1948362
ROD AS
320C, 325C, 325C L, 330C L
320C, 325C, 325C L, 330C L
2050519
ROD
320C
320C
2897888
ROD AS
322C
322C
2897880
ROD AS
322C
322C