1U3522 ROD AS-PISTON Caterpillar parts
980C, 980F, 980F II
Rating:
Alternative (cross code) number:
CA1U3522
1U-3522
1U3522
CA1U3522
1U-3522
1U3522
Weight: 213 pounds 96 kg.
Information:
ROD DIAMETER
88.85
mm
ROD END TYPE
NUT
ROD EYE TYPE
5
ROD LENGTH
1353
mm
WHEEL LOADER,
Related part:
1U3522
ROD AS-YM
3905281
CL
1U3522
ROD AS-PISTON
0R1175
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 1U3522 Hydraulic Cylinder Piston Rod for Model 980C/980F/980F II
CTP For Model 980C/980F/980F II || Sold in each || Easy in-and-out fit
CTP For Model 980C/980F/980F II || Sold in each || Easy in-and-out fit
CTP 1U3522 Hydraulic Cylinder Piston Rod for Model 980C/980F/980F II
CTP For Model 980C/980F/980F II || Sold in each || Easy in-and-out fit
CTP For Model 980C/980F/980F II || Sold in each || Easy in-and-out fit
Information:
Installation Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     5P-3526     Piston Ring Compressor     1    
B     9S-9082     Engine Turning Tool     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Put clean engine oil on the pistons, on the piston rings, and in the cylinder liners.
Use Tool (B) and turn the crankshaft so that the corresponding crank pin for the connecting rod and piston that is to be installed is at the bottom center position.
Illustration 1 g00786646
Top view of cylinder numbers
The connecting rods have numbers stamped on the tab slot side of the connecting rod. Numbers are also stamped on the bearing caps. The number designates which cylinder to install the piston and rod. Etch the cylinder number in the proper location on a connecting rod and bearing cap that does not have a number.
Illustration 2 g00786604
Cross section of connecting rod
The connecting rod and piston are to be installed in the engine with surface (D) adjacent to the thrust surface of the crank pin. Surface (C) is to thrust against the mating rod on the same crank pin. Be sure to install the connecting rod and piston with this orientation.
Illustration 3 g00566325
Use Tool (A) and a soft hammer to install piston (2) and the connecting rod in the cylinder liner.
Install the bearing cap on the connecting rod. The number on the side of the bearing cap is on the same side as the number on the connecting rod.
Illustration 4 g00568813
Thoroughly lubricate the threads of the bolts on the connecting rod with clean engine oil. Install the bearing cap and the nuts. Tighten nuts (1) on the bearing cap to a torque of 82 8 N m (60 6 lb ft). Put a mark on each nut and on each bearing cap. Tighten each nut an additional 120 5 degrees.
Repeat Steps 1 through 7 in order to install the remainder of the remainder of the pistons and connecting rods.End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     5P-3526     Piston Ring Compressor     1    
B     9S-9082     Engine Turning Tool     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Put clean engine oil on the pistons, on the piston rings, and in the cylinder liners.
Use Tool (B) and turn the crankshaft so that the corresponding crank pin for the connecting rod and piston that is to be installed is at the bottom center position.
Illustration 1 g00786646
Top view of cylinder numbers
The connecting rods have numbers stamped on the tab slot side of the connecting rod. Numbers are also stamped on the bearing caps. The number designates which cylinder to install the piston and rod. Etch the cylinder number in the proper location on a connecting rod and bearing cap that does not have a number.
Illustration 2 g00786604
Cross section of connecting rod
The connecting rod and piston are to be installed in the engine with surface (D) adjacent to the thrust surface of the crank pin. Surface (C) is to thrust against the mating rod on the same crank pin. Be sure to install the connecting rod and piston with this orientation.
Illustration 3 g00566325
Use Tool (A) and a soft hammer to install piston (2) and the connecting rod in the cylinder liner.
Install the bearing cap on the connecting rod. The number on the side of the bearing cap is on the same side as the number on the connecting rod.
Illustration 4 g00568813
Thoroughly lubricate the threads of the bolts on the connecting rod with clean engine oil. Install the bearing cap and the nuts. Tighten nuts (1) on the bearing cap to a torque of 82 8 N m (60 6 lb ft). Put a mark on each nut and on each bearing cap. Tighten each nut an additional 120 5 degrees.
Repeat Steps 1 through 7 in order to install the remainder of the remainder of the pistons and connecting rods.End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Caterpillar parts catalog:
Parts rod Caterpillar catalog:
8B3768
ROD END
120G, 12E, 12G, 16, 215, 215B, 215D, 225, 225D, 229, 229D, 231D, 235, 235C, 245, 245B, 3114, 3116, 3126, 315B FM L, 3208, 320B FM LL, 322B L, 322C, 325B L, 330B L, 3406, 517, 527, 583H, 613C, 615, 615...
120G, 12E, 12G, 16, 215, 215B, 215D, 225, 225D, 229, 229D, 231D, 235, 235C, 245, 245B, 3114, 3116, 3126, 315B FM L, 3208, 320B FM LL, 322B L, 322C, 325B L, 330B L, 3406, 517, 527, 583H, 613C, 615, 615...
8N1726
ROD ASSEM.
16G, 245, 3406, 3406B, 578, 621, 621E, 623E, 627E, 826C, 980C, G3406
16G, 245, 3406, 3406B, 578, 621, 621E, 623E, 627E, 826C, 980C, G3406
7N7444
ROD AS-AIR COMPRESSOR
14G, 16G, 3176, 3176B, 3304, 3306, 3306B, 3406B, 3406E, 3512, 615C, 621, 621E, 621R, 815B, 966C, 966D, 966F, 966F II, 980C, 980F, C-10, C-12, D25C, D300B, D30C, D350C, D35C
14G, 16G, 3176, 3176B, 3304, 3306, 3306B, 3406B, 3406E, 3512, 615C, 621, 621E, 621R, 815B, 966C, 966D, 966F, 966F II, 980C, 980F, C-10, C-12, D25C, D300B, D30C, D350C, D35C
0R3780
ROD AS-CONNECTING
3406E, 375 L, 578, 621G, 623G, 627G, 735, 824C, 824G, 825G, 826G, 980C, 980G, C-15, C-16, D8N, D8R, D8R II
3406E, 375 L, 578, 621G, 623G, 627G, 735, 824C, 824G, 825G, 826G, 980C, 980G, C-15, C-16, D8N, D8R, D8R II
9K8757
ROD END
140, 153, 215, 225, 227, 235, 245, 518, 571G, 825C, 910, 931B, 931C, 931C II, 933, 933C, 935B, 935C, 939, 939C, 950B, 966C, 966D, 980C, D3, D399, D3B, D3C II, D3C III, D4C, D4C III, D4E, D5B, D5C III,...
140, 153, 215, 225, 227, 235, 245, 518, 571G, 825C, 910, 931B, 931C, 931C II, 933, 933C, 935B, 935C, 939, 939C, 950B, 966C, 966D, 980C, D3, D399, D3B, D3C II, D3C III, D4C, D4C III, D4E, D5B, D5C III,...
8K1253
ROD END
140B, 225, 245, 910, 931B, 938F, 938G, 938G II, 938H, 950F, 950F II, 960F, 966F, 966F II, 966G II, 970F, 980C, 980F, 980F II, 980G, 988B, 988F, 988F II, 990, 990 II, 990H, 992C, 992D, 994, 994D, D379,...
140B, 225, 245, 910, 931B, 938F, 938G, 938G II, 938H, 950F, 950F II, 960F, 966F, 966F II, 966G II, 970F, 980C, 980F, 980F II, 980G, 988B, 988F, 988F II, 990, 990 II, 990H, 992C, 992D, 994, 994D, D379,...
8S7048
ROD END
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 24M, 55, 57, 572G, 58, 594H, 814B, 815B, 816B, 826C, 910, 931B, 933, 936F, 939...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 24M, 55, 57, 572G, 58, 594H, 814B, 815B, 816B, 826C, 910, 931B, 933, 936F, 939...
4M0495
ROD END
120G, 12G, 130G, 140G, 14G, 160G, 16G, 518, 518C, 528, 528B, 530B, 561C, 561D, 571G, 583K, 768B, 769, 773, 815, 816, 950, 955H, 955L, 966C, 977H, 977L, 980, 980B, 980C, 988, 992, D4D, D5, D7F, D7G, D8...
120G, 12G, 130G, 140G, 14G, 160G, 16G, 518, 518C, 528, 528B, 530B, 561C, 561D, 571G, 583K, 768B, 769, 773, 815, 816, 950, 955H, 955L, 966C, 977H, 977L, 980, 980B, 980C, 988, 992, D4D, D5, D7F, D7G, D8...
0R3781
ROD AS-CONNECTING
16H NA, 621F, 623E, 623F, 627B, 627F, 814B, 980C, 980F, D400, D8N
16H NA, 621F, 623E, 623F, 627B, 627F, 814B, 980C, 980F, D400, D8N
8V9570
ROD-INDICATOR
69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777B, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 793D, 824C, 980C, 980F
69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777B, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 793D, 824C, 980C, 980F
5V7162
ROD END
950B, 966D, 980C
950B, 966D, 980C
9J4916
ROD AS
980C, 980F
980C, 980F
9T1762
ROD AS
980C, 980F
980C, 980F
8V9570
ROD-INDICATOR
69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777B, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 793D, 824C, 980C, 980F
69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777B, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 793D, 824C, 980C, 980F
7V2058
ROD AS
824C, 825C, 826C, 980C
824C, 825C, 826C, 980C
9V0182
ROD
815B, 825C, 826C, 950B, 950F, 966D, 966F, 980C, 980F
815B, 825C, 826C, 950B, 950F, 966D, 966F, 980C, 980F
6W4686
ROD
825C, 826C, 980C, 980F
825C, 826C, 980C, 980F
8R4193
ROD
980C, 980F
980C, 980F
5V7165
ROD AS
950B, 966D, 980C
950B, 966D, 980C
6W0657
ROD-CLEVIS
980C
980C
5V7162
ROD END
950B, 966D, 980C
950B, 966D, 980C
9T2420
ROD AS
980C, 980F, 980F II, 980G, 980G II, 980H
980C, 980F, 980F II, 980G, 980G II, 980H
3G4423
ROD AS
980C, 980F, 980F II
980C, 980F, 980F II
9J5555
ROD AS-PISTON
980C, 980F, 980F II
980C, 980F, 980F II