ROD AS 2321683 - Caterpillar

2321683 ROD AS Caterpillar parts 5110B

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2321683
232-1683
2321683

Weight: 1130 pounds 512 kg.

Buy ROD AS 2321683 Caterpillar genuine, new aftermarket tractor parts with delivery
MINING EXCAVATOR,

Compatible equipment models: 2321683:

MINING EXCAVATOR 5110B Caterpillar

Number on catalog scheme: 5

For full view, you need register

Information:

Illustration 1 g02042457
Schematic of the "Auxliary Pedal 1 Control Pressure" SensorThis diagnostic code is associated with the "Auxilairy Pedal 1 Control Pressure" Sensor. This diagnostic code is recorded when the Machine ECM reads the sensor signal voltage and the voltage is too low. The possible causes of this failure are listed below:
The sensor has failed.
The signal circuit in the machine harness is shorted to ground.
The Machine ECM has failed. A failure of the ECM is unlikely.Test Step 1. CHECK THE SENSOR.
Disconnect the machine harness from the sensor. Expected Result:The diagnostic code changes from CID 3577 FMI 04 to a CID 3577 FMI 03 diagnostic code. Results:
OK - The diagnostic code changed to CID 3577 FMI 03. This change indicates that the failure is no longer present. The sensor has failed.Repair: Replace the sensor.STOP
NOT OK - The diagnostic code CID 3577 FMI 04 remained active. This change indicates that the failure remains present. The sensor is not the cause of the failure. Proceed to Test Step 2.Test Step 2. CHECK THE HARNESS.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J1 machine harness connector from the Machine ECM.
At the harness connector for the sensor, measure the resistance between the signal contact 3 (wire N795-WH) and frame ground. Expected Result:The resistance is greater than 5000 ohms. Results:
OK - The resistance is greater than 5000 ohms. The harness circuit resistance is correct. The Machine ECM may have failed. Repair: A failure of the Machine ECM is unlikely. Exit this procedure and perform this diagnostic code procedure again. If the failure is not found, replace the Machine ECM. See the Testing and Adjusting, "Electronic Control Module (ECM) - Replace" section of this manual. STOP
NOT OK - The resistance is less than 5000 ohms. The machine harness has failed. There is a short between frame ground and the signal circuit in the machine harness. Repair: Repair the machine harness or replace the machine harness. STOP

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

5110B L Excavator AAK00001-UP (MACHINE) POWERED BY 3412E Engine

205-7222: CYLINDER GP-WORK TOOL » SEBP35660365
205-7222: CYLINDER GP-WORK TOOL » SEBP35660366

Parts rod Caterpillar catalog:

1S4589 ROD
245, 245B, 245D, 24H, 3406, 3406B, 3406E, 3408, 3408B, 3408C, 3412, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B, 3516C, 375, 375 L, 5080, 5110B, 5130, 5130B, 5230B, 621B, 621E, 621F, 623E, 623...

1608178 ROD AS-CONNECTING
24H, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 5110B, 589, 631D, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 69D, 769C, 769D, 771C, 771D, 773B, 773D, 773E, 775B, 775D, 775E, 834B, 836, 844, 988B, 988F,...

0874704 ROD
307, 307B, 311, 311B, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322B L, 322B LN, 322C, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 L, 330B L, 345B, 345B II, 345B L, 350, 350 L, 375, 37...

1184086 ROD
307C, 308C, 311, 311B, 311C, 311D LRR, 311F LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E ...

2163873 ROD AS
5110B

2469059 ROD AS
5110B

1667638 ROD
5110B

1667640 ROD
5110B

2057712 ROD AS
5110B

2469054 ROD AS
5110B

2057227 ROD AS
5110B

2281641 ROD AS
5110B

2057227 ROD AS
5110B

2469054 ROD AS
5110B

2057712 ROD AS
5110B

1990117 ROD
385B, 385C, 385C FS, 385C L, 385C L MH, 5090B