2427160 ROD Caterpillar parts
CP-433E, CP-44, CS-423E, CS-433E, CS-44
Rating:
Alternative (cross code) number:
CA2427160
242-7160
2427160
CA2427160
242-7160
2427160
Weight: 0.010 pounds 0 kg.
Information:
LENGTH
122
mm
THREAD LENGTH A
35
mm
THREAD LENGTH B
35
mm
THREAD SIZE A
M8X1.25
THREAD SIZE B
M8X1.25
TYPE
BOTH END
VIBRATORY COMPACTOR,
Compatible equipment models: 2427160:
Number on catalog scheme:
3
For full view, you need register
Caterpillar parts catalog:
Information:
Removal Procedure
Start By:
Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "Main Hydraulic System - Pressure Release" in this manual.
At operating temperature, the hydraulic oil is hot and under pressure. Hot oils can cause burns.To prevent possible personal injury, release the pressure in the implement hydraulic circuit (boom, stick, bucket, and swing), travel circuits, and the hydraulic oil tank at the filler cap before any hydraulic lines or components are disconnected or removed.Remove the filler cap only when the engine is stopped and the filler cap is cool enough to touch.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Failure to properly assemble parts or failure to follow established procedures can lead to damage of the parts and assembly.To avoid damage to parts, always identify and mark the parts so that they can be installed in the same location. Ensure that gear surfaces align. Never force parts during assembly.
Mark the position of the swing motor in relation to the swing drive so that the swing motor can be installed in the original position.
Drain the oil from the swing drive into a suitable container for storage or disposal. The capacity of the swing drive is 1.5 L (0.4 US gal).
Illustration 1 g00544255
Illustration 2 g00533539
Disconnect seven hose assemblies (2) from the swing motor.
Remove swing parking brake control valve (1) in order to gain access to the mounting bolts for the swing motor. Remove three O-ring seals (6) from the body of the swing parking brake control valve. Note: One of the mounting bolts for the swing motor is located under oil level gauge tube (3). The mounting bolt can be loosened for removal of the swing motor. The bolt cannot be completely removed.
Remove six bolts (5) and the washers that hold swing motor (4) to the swing drive.
Illustration 3 g00533540
Illustration 4 g00533542
Fasten a lifting strap and a hoist to the swing motor. Use two screwdrivers to pry swing motor (4) from the ring gear of the swing drive. Two slots (7) are provided in order to separate the components. Note: The hydraulic oil tank is removed for a better illustration of the swing motor.
Carefully remove swing motor (4) from the swing drive. The weight of the swing motor is 23 kg (51 lb).
Start By:
Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "Main Hydraulic System - Pressure Release" in this manual.
At operating temperature, the hydraulic oil is hot and under pressure. Hot oils can cause burns.To prevent possible personal injury, release the pressure in the implement hydraulic circuit (boom, stick, bucket, and swing), travel circuits, and the hydraulic oil tank at the filler cap before any hydraulic lines or components are disconnected or removed.Remove the filler cap only when the engine is stopped and the filler cap is cool enough to touch.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Failure to properly assemble parts or failure to follow established procedures can lead to damage of the parts and assembly.To avoid damage to parts, always identify and mark the parts so that they can be installed in the same location. Ensure that gear surfaces align. Never force parts during assembly.
Mark the position of the swing motor in relation to the swing drive so that the swing motor can be installed in the original position.
Drain the oil from the swing drive into a suitable container for storage or disposal. The capacity of the swing drive is 1.5 L (0.4 US gal).
Illustration 1 g00544255
Illustration 2 g00533539
Disconnect seven hose assemblies (2) from the swing motor.
Remove swing parking brake control valve (1) in order to gain access to the mounting bolts for the swing motor. Remove three O-ring seals (6) from the body of the swing parking brake control valve. Note: One of the mounting bolts for the swing motor is located under oil level gauge tube (3). The mounting bolt can be loosened for removal of the swing motor. The bolt cannot be completely removed.
Remove six bolts (5) and the washers that hold swing motor (4) to the swing drive.
Illustration 3 g00533540
Illustration 4 g00533542
Fasten a lifting strap and a hoist to the swing motor. Use two screwdrivers to pry swing motor (4) from the ring gear of the swing drive. Two slots (7) are provided in order to separate the components. Note: The hydraulic oil tank is removed for a better illustration of the swing motor.
Carefully remove swing motor (4) from the swing drive. The weight of the swing motor is 23 kg (51 lb).
Parts rod Caterpillar catalog:
2026498
ROD
CP-433E, CP-573E, CS-423E, CS-433E, CS-563E, CS-583E
CP-433E, CP-573E, CS-423E, CS-433E, CS-563E, CS-583E
1942081
ROD
CP-433E, CS-423E
CP-433E, CS-423E
2109474
ROD AS
RM-250C
RM-250C
1599141
ROD-SLIDE
CB-214D
CB-214D
1683653
ROD
CB-214D, CB-214E, CB-22, CB-334E, CB-34
CB-214D, CB-214E, CB-22, CB-334E, CB-34
1654749
ROD AS
AP-1055D, AS2301, BG-2455D, BG-260D
AP-1055D, AS2301, BG-2455D, BG-260D
2291669
ROD
AP-655C
AP-655C
1610506
ROD
AP-600D, AP-655D, CB-434D
AP-600D, AP-655D, CB-434D
2850841
ROD-CONTROL
CB-434D
CB-434D
2176670
ROD-THREADED
CB-434D, CB-534D, CB-54, CB-564D, CB-64
CB-434D, CB-534D, CB-54, CB-564D, CB-64
2258354
ROD
CB-434D, CB-534D, CB-54, CB-564D, CB-64
CB-434D, CB-534D, CB-54, CB-564D, CB-64
2284839
ROD
CB-534D, CB-564D, CD-54
CB-534D, CB-564D, CD-54