AVSPARE.COM
parts catalog

ROD AS. 3236674 - Caterpillar



3236674 ROD AS. Caterpillar parts ROD
Rating:
26
Alternative (cross code) number:
CA3236674
323-6674
3236674
Caterpillar 3236674 ROD AS.
Weight: 10 pounds 4 kg.

Buy ROD AS. 3236674 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Remove pin assembly (7).
Illustration 5 g01689253
Carefully reposition hose assemblies (8) through heel (2) as stick (1) is being raised away from heel (2). Remove shims (9) (not shown). The weight of heel (2) is approximately 517 kg (1140 lb).Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 452-6006 Grease 1
Illustration 6 g01689775
Position heel (2) under stick (1). The weight of heel (2) is approximately 517 kg (1140 lb).
Apply Tooling (A) to the bearings in the pin bore for heel (2). Apply Tooling (A) to the pin bore for stick (1) and to the pin bore for the heel cylinder.
Lower stick (1) into heel (2). Carefully position hose assemblies (8) through heel (2) as stick (1) is being lowered.
Illustration 7 g01688953
Apply Tooling (A) to pin assembly (7).
Use a suitable hammer and a suitable punch to install pin assembly (7) into the heel and the stick.
Illustration 8 g00730428
Typical Example
(a) Dimension of Lateral Clearance (a)
( b) Dimension of Lateral Clearance (b)
( X) Heel
(Y) Stick
(3) Retaining bolt
(4) Pin
Measure the total lateral clearance between the heel and the stick at the pin bore.
The total lateral clearance of Dimension (a) plus Dimension (b) cannot be more than 1.6 mm (0.06 inch).
If the total clearance is less than 1.6 mm (0.06 inch), the addition of shims between the heel and the stick will not be required. Proceed to Step 13.
If the total clearance is more than 1.6 mm (0.06 inch), add the correct shims to obtain the necessary clearance. Proceed to Step 10.
Use the following table to determine the correct shims .
Table 2
Table for Shims
Shims Thickness (mm)
133-2425 0.5
093-0083 1.0
093-0115 2.0 Note: Refer to the Parts Manual for current part numbers.
If shims need to be installed, use a suitable hammer and a suitable punch to remove pin assembly (7).
Install the shims at the pin bores between the heel and the stick on the same side as the pin retaining bolt as shown in Illustration 8.
Use a suitable hammer and a suitable punch to reinstall pin assembly (7).
Illustration 9 g01689743
Apply Tooling (A) to the pin assembly that holds heel cylinder (5) to heel (2).
Lower heel cylinder (5) until the pin bore in the rod is in alignment with the pin bore in heel (2). Extend the cylinder rod or retract the cylinder rod to align the pin bores.
Illustration 10 g01689813
Use a suitable hammer and a suitable punch to install pin assembly (4) into the pin bores.
Illustration 11 g00733006
Typical Example
(a) Dimension of Lateral Clearance (a)
( b) Dimension of Lateral Clearance (b)
( 1) Pin
(V) Heel Cylinder
(W) Heel
Measure the total lateral clearance between the heel cylinder and the heel.
The total lateral clearance of Dimension (a) plus Dimension (b) cannot be more than 1.6 mm (0.06 inch).
If the total clearance is less than 1.6 mm (0.06 inch), the addition of shims between the heel and the stick will not be required. Proceed to Step 24.
If the total clearance is more than 1.6 mm (0.06 inch), add the correct shims to obtain the necessary clearance. Proceed to Step 21.
Use the following table to determine the correct shims.
Table


Parts rod Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.