3639751 ROD AS Caterpillar parts
G325B, VRG-40/2
Rating:
Alternative (cross code) number:
CA3639751
363-9751
3639751
CA3639751
363-9751
3639751
Weight: 35 pounds 16 kg.
GRAPPLE-DEM/SORT,
Number on catalog scheme:
8
For full view, you need register
Information:
Setting the Beeper
The display includes an internal beeper. The beeper can be configured to provide an audible signal when any of the events that are listed in Table 1 occur.
Table 1
Event Sounds when...
Above Grade the blade is more than one times the vertical tolerance and less than four times the vertical tolerance above grade.
On Grade the blade is within the vertical tolerance of grade.
Below Grade the blade is more than one times the vertical tolerance and less than four times the vertical tolerance below grade.
Warning Messages a warning message appears and when a warning message automatically disappears.
GPS Accuracy the GPS accuracy mode changes.
ATS Tracking the ATS loses lock on the machine target.
Laser Receiver the laser receiver loses strikes from the laser transmitter.
Auto/Manual States the guidance mode changes to Auto, Manual or Inactive Auto.
Key/Switch Beeps a key or a switch is pressed.
Avoidance Zone the machine is within the warning distance of an avoidance zone or if the No Avoid message is displayed. The beeper also sounds in a continuous pattern when the machine is within the avoidance zone. Avoidance zone beeper tones cannot be disabled. Perform the following steps in order to access the "Beeper" dialog.
Illustration 1 g01833974
The AccuGrade System must be in service mode in order to access the setup for the beeper. From the "Setup Menu – Configuration" dialog, press the arrow keys until "Beeper" is highlighted.
Press the "OK" key. The "Beeper" dialog appears. Refer to Illustration 2.Events that are disabled are identified by an "X" in the box. Events that are enabled are identified by a check mark. Events that cannot be disabled are identified by a grayed out check mark. Subevents that cannot be disabled independent of their master event are also identified by a grayed out check mark.
Illustration 2 g01834013
Press the arrow keys in order to select different events.
Press the first soft key on the right hand side of the display in order to enable or disable an event.The different events emit different beeper patterns. To hear the pattern for a particular event, press the "TEST" soft key when the event is selected.
Do one of the following.
Press the "OK" key in order to confirm the setting. The setup for the beeper is saved. The "Beeper" dialog is closed and the "Setup Menu – Configuration" dialog appears. The changes take effect immediately.
Press the "ESC" key and then press the "OK" key in order to return to the "Setup Menu – Configuration" dialog without saving the changes.
Press the "ESC" key in order to exit the "Setup Menu – Configuration" dialog.
The display includes an internal beeper. The beeper can be configured to provide an audible signal when any of the events that are listed in Table 1 occur.
Table 1
Event Sounds when...
Above Grade the blade is more than one times the vertical tolerance and less than four times the vertical tolerance above grade.
On Grade the blade is within the vertical tolerance of grade.
Below Grade the blade is more than one times the vertical tolerance and less than four times the vertical tolerance below grade.
Warning Messages a warning message appears and when a warning message automatically disappears.
GPS Accuracy the GPS accuracy mode changes.
ATS Tracking the ATS loses lock on the machine target.
Laser Receiver the laser receiver loses strikes from the laser transmitter.
Auto/Manual States the guidance mode changes to Auto, Manual or Inactive Auto.
Key/Switch Beeps a key or a switch is pressed.
Avoidance Zone the machine is within the warning distance of an avoidance zone or if the No Avoid message is displayed. The beeper also sounds in a continuous pattern when the machine is within the avoidance zone. Avoidance zone beeper tones cannot be disabled. Perform the following steps in order to access the "Beeper" dialog.
Illustration 1 g01833974
The AccuGrade System must be in service mode in order to access the setup for the beeper. From the "Setup Menu – Configuration" dialog, press the arrow keys until "Beeper" is highlighted.
Press the "OK" key. The "Beeper" dialog appears. Refer to Illustration 2.Events that are disabled are identified by an "X" in the box. Events that are enabled are identified by a check mark. Events that cannot be disabled are identified by a grayed out check mark. Subevents that cannot be disabled independent of their master event are also identified by a grayed out check mark.
Illustration 2 g01834013
Press the arrow keys in order to select different events.
Press the first soft key on the right hand side of the display in order to enable or disable an event.The different events emit different beeper patterns. To hear the pattern for a particular event, press the "TEST" soft key when the event is selected.
Do one of the following.
Press the "OK" key in order to confirm the setting. The setup for the beeper is saved. The "Beeper" dialog is closed and the "Setup Menu – Configuration" dialog appears. The changes take effect immediately.
Press the "ESC" key and then press the "OK" key in order to return to the "Setup Menu – Configuration" dialog without saving the changes.
Press the "ESC" key in order to exit the "Setup Menu – Configuration" dialog.
Caterpillar parts catalog:
Parts rod Caterpillar catalog:
2336852
ROD AS
385B, 385C L, 385C L MH
385B, 385C L, 385C L MH
3212536
ROD
S365C, VHS-60/4
S365C, VHS-60/4
3178435
ROD AS
365C L, 385C, 385C L, 390D, 390D L, 390F L
365C L, 385C, 385C L, 390D, 390D L, 390F L
3153374
ROD AS
365C L, 385C, 385C L
365C L, 385C, 385C L
1733363
ROD AS
385B, 385C, 385C L, 390D, 390D L, 390F L
385B, 385C, 385C L, 390D, 390D L, 390F L
2487161
ROD
365C L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L
365C L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L
3891056
ROD AS
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L
2344463
ROD AS
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 365B, 365C
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 365B, 365C
3509343
ROD AS
329D, 329D L, 329E, 329E L, 329E LN
329D, 329D L, 329E, 329E L, 329E LN
2703490
ROD AS
STIFF LINK
STIFF LINK
3662663
ROD AS
G315B, G325B, VRG-40/2
G315B, G325B, VRG-40/2
3395393
ROD-HYDRAULIC CYLINDER
G325B, VRG-40/2
G325B, VRG-40/2