AVSPARE.COM
parts catalog

ROD AS 4415704 - Caterpillar



4415704 ROD AS Caterpillar parts 627K, 627K LRC ROD
Rating:
20
Alternative (cross code) number:
CA4415704
441-5704
4415704
Caterpillar 4415704 ROD AS
Weight: 0.40 pounds 0 kg.

Buy ROD AS 4415704 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL TRACTOR-SCRAPER,

Compatible equipment models: 4415704:

WHEEL TRACTOR-SCRAPER  627K   627K LRC   Caterpillar
  For full view, you need register

Information:


Illustration 1 g00592670
Schematic of the Solenoid Valve (Fan Reversing)This diagnostic code is associated with the Solenoid Valve (Fan Reversing). The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal. The possible causes of the diagnostic code are listed:
The solenoid has failed.
The energize circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0485 FMI 03 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:When this diagnostic code occurs, the direction of the engine fan will always be reversed.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connectors from the solenoid and the ECM.
At the machine harness connector for the ECM, measure the resistance from contact J1-10 (wire H704-PK) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms. Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-10 (H704-PK) and the circuit that has a low resistance measurement. Repair: Repair the machine harness or replace the machine harness. Stop.Test Step 2. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 0485 FMI 03 is active.Expected Result:The CID 0485 FMI 03 is active.Results:
YES - The CID 0485 FMI 03 is active. The problem has not been corrected. The ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". Stop.
NO - The CID 0485 FMI 03 is not active. The problem does not exist at this time.Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation. Stop.


Parts rod Caterpillar catalog:

4347589 ROD-FILTER
621K, 623K, 623K LRC, 627K, 627K LRC
3758970 ROD AS
621K, 623K, 623K LRC, 627K, 627K LRC
4167455 ROD AS
621K, 627K, 627K LRC
4215378 ROD
901C, 902C, 903C
2434456 ROD AS
901C, 902C, 903C
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.