AVSPARE.COM
parts catalog

ROD B23602901 - Caterpillar



B23602901 ROD Caterpillar parts E140 ROD
Rating:
82
Alternative (cross code) number:
CAB23602901
B2360-2901
B23602901
Caterpillar B23602901 ROD

Buy ROD B23602901 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: B23602901:

EXCAVATOR  E140   Caterpillar
Number on catalog scheme: 17
  
  For full view, you need register

Information:

21. Remove clip (33). Disconnect wire assembly (32) from the governor cylinder. 22. Disconnect hose assemblies (34) and (35) from the governor cylinder. Put plugs in the ends of the hose assemblies. 23. Put identification marks on three wires (36) that are connected to the fuel shutoff solenoid. Disconnect the three wires from the fuel shutoff solenoid. 24. Remove tie wrap (37) from the wires that are routed to the fuel shutoff solenoid and the air conditioning compressor. 25. Disconnect wiring harness (38) for the air conditioning compressor. 26. Loosen bolts (39) and (40). Remove the nuts, washers and bolts (41) that hold plate (42) to air conditioning compressor (43). 27. Remove the air conditioning compressor mounting bolt (44), the washer and nut. Carefully lift the air conditioning compressor from the engine, and lay it to the side, out of the way. 28. Disconnect fuel hose assemblies (45) and (46). Put plugs in the ends of the hose assemblies to prevent fuel loss and to keep dirt out of the fuel system. 29. Disconnect pressure switch electrical connector (47). 30. Remove two tie wraps (48) from the wiring harness for the engine speed senor. Disconnect wiring harness (49). 31. Fasten Tool (A) and a hoist to the engine as shown.32. Remove four engine mounting bolts (50) that hold the engine to the frame of the machine.
Prior to removing the engine and main hydraulic pump from the machine, make sure all hose assemblies, tube assemblies and wires have been disconnected properly.
33. Carefully remove engine and main hydraulic pump (51), as a unit, from the machine. The combined weight of the engine and main hydraulic pump is 816 kg (1800 lb). 34. Remove two mounting bolts (52) and front engine mounting bracket (53). Remove the other front engine mounting bracket. 35. Remove two mounting bolts (54) and rear engine mounting bracket (55). Remove the other rear engine mounting bracket. The following steps are for the installation of the engine and main hydraulic pump.
Visually check the condition of the rubber mounts in the front and rear engine mounting brackets. If the rubber mounts are worn or damaged or appear to be compressed, use new parts for replacement.
36. Check the condition of all O-ring seals used in the ends of the hose assemblies and tube assemblies that connect at the engine or the main hydraulic pump. If any of the seals are worn or damaged, use new parts for replacement. 37. Install two rear engine mounting brackets (55) and four bolts (54). 38. Install two front engine mounting brackets (53) and four bolts (52). 39. Fasten Tool (A) and a hoist to the engine as shown.40. Carefully install engine and main hydraulic pump (51), as a unit, in the machine. Install four engine mounting bolts (50), but do not tighten the bolts at this time.41. Make sure the fan assembly of the engine is centered in the radiator shroud and no blades are touching the shroud. It may be necessary to

Caterpillar parts catalog:

Caterpillar parts catalog
E140 HYDRAULIC EXCAVATOR 1NF00001-09040 (MACHINE) POWERED BY 6D14 ENGINE


Parts rod Caterpillar catalog:

0964504 ROD
307, 312, 315, 317, 325, 325 LN, 350, 375, 5080, E110B, E120B, E140, E200B, E240C, E300B, E70B, EL240B
0962915 ROD
311, 311B, 312, 312B, 312B L, 315, 315B L, 317, 317B LN, 318B, 318C, 319C, 320B, 320B U, 321B, 322B L, 322B LN, 325B, 325B L, 330B L, E110, E120, E140, E200B, E300, E300B, M325B, W330B
0966750 ROD
307, E110, E120, E140, E180, E70
0936536 ROD
311, E110, E140
0855739 ROD
311, E110, E110B, E120, E120B, E140
0938513 ROD
E110, E120, E140, E240
0931646 ROD
E110, E120, E140
0931646 ROD
E110, E120, E140
0938513 ROD
E110, E120, E140, E240
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.