AVSPARE.COM
parts catalog

ROLLER-NEEDLE 1128444 - Caterpillar


1128444 ROLLER-NEEDLE Caterpillar parts 35, 45, 55
Rating:
57
Alternative (cross code) number:
CA1128444
112-8444
1128444
Caterpillar 1128444 ROLLER-NEEDLE
Weight: 0.03 pounds 0 kg.

Buy ROLLER-NEEDLE 1128444 Caterpillar genuine, new aftermarket tractor parts with delivery
CHALLENGER,

Compatible equipment models: 1128444:

CHALLENGER  35   45   55   Caterpillar
Number on catalog scheme: 9
  For full view, you need register

Information:


Illustration 1 g01233621
Transmission Gear Shift Solenoid 1 CircuitThis diagnostic code is recorded when the ECM reads the voltage of the solenoid circuit as above normal (short to the +battery circuit).Note: This procedure can cause new diagnostic codes to be recorded. Ignore these created diagnostic codes. Complete the following procedure. Then clear the created diagnostic codes.Note: The approximate coil resistance of the solenoid is 8.7 .4 ohms at 25 °C (77.0 °F).Test Step 1. CHECK THE SIGNAL CIRCUIT OF THE SOLENOID FOR A SHORT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the solenoid.
Disconnect the machine harness connectors J1 and J2 from the ECM.
At the J1 and J2 machine harness connectors for the ECM, measure the resistance from the signal contact of the solenoid J2-6 (wire J610-WH) to the +battery circuit. Expected Result:Each resistance that is measured is greater than 5 ohms.Results:
YES - Each resistance that is measured is greater than 5.0 ohms. Proceed to test step 2.
NO - One or more of the resistance measurements is less than 5 ohms. There is a short in the machine harness.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Clear all of the inactive diagnostic codes.
Stop the machine. Then place the parking brake switch in the ON position.
Observe the status of the diagnostic code. The diagnostic code is present or the diagnostic code is NOT present.Expected Result:The diagnostic code for the relay is NO longer present.Results:
YES - The diagnostic code is NOT present.Repair: The diagnostic code does not exist at this time. The initial diagnostic code was probably caused by a poor electrical connection and/or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation. STOP
NO - The diagnostic code has not been corrected. It is unlikely that the ECM has failed.Repair: Exit this procedure and perform this diagnostic code again. Recheck the status of the diagnostic code. The diagnostic code is active or the diagnostic code is NOT active. Replace the ECM if the cause is not found. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". STOP

Caterpillar parts catalog:

Caterpillar parts catalog
Challenger 35 and Challenger 45 Agricultural Tractors 1DR00001-01699 (MACHINE) POWERED BY 3116 Engine
Challenger 55 Agricultural Tractor 7DM00001-00849 (MACHINE) POWERED BY 3126 Engine
Challenger 35 & Challenger 45 Agricultural Tractors 1DR01700-UP (MACHINE) POWERED BY 3116 Engine
Challenger 55 Agricultural Tractor 7DM00850-UP (MACHINE) POWERED BY 3126 Engine
Challenger 35, Challenger 45 & Challenger 55 Agricultural Tractors 4DZ00001-UP (MACHINE) POWERED BY 3116 & 3126 Engines
Challenger 55 Agricultural Tractor 60 in (1524 mm) Base Gauge 6NN00001-UP (MACHINE) POWERED BY 3126 Engine
Challenger 35 & Challenger 45 Agricultural Tractors 60 in (1524 mm) Base Gauge 8RD00001-UP (MACHINE) POWERED BY 3116 Engine
Challenger 35 & Challenger 45 Agricultural Tractors 80 in (2032 mm) Base Gauge 3BK00001-UP (MACHINE) POWERED BY 3116 Engine
Challenger 35, Challenger 45 & Challenger 55 Agricultural Tractors 60 in (1524 mm) Track Gauge & 80 in (2032 mm) Track Gauge 3HS00001-UP (MACHINE) POWERED BY 3116 & 3126 Engines
Challenger 55 Agricultural Tractor 80 in (2032 mm) Base Gauge AEN00001-UP (MACHINE) POWERED BY 3126 Engine


Parts roller Caterpillar catalog:

8E3131 ROLLER-CAM
45, 55, D6N, D6T, D8N, D8R, D8R II, D9R
1105397 ROLLER
3054, 3056, 307, 312, 416B, 416C, 426B, 426C, 428B, 428C, 436B, 436C, 438B, 438C, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433C, CS-323C, CS-431C, PS-150B, PS-...
1735734 ROLLER
TH62, TH63, TH82, TH83
8R1571 ROLLER
65, 75C, 85C, M325C MH, M325D L MH, M325D MH
1P3958 ROLLER AS-SPECIAL
14G, 14H, 14H NA, 24H, 24M, 30/30, 611, 615, 615C, 65, 65C, 65E, 735, 735B, 740, 740B, 75, 75C, 75D, 75E, 777B, 816B, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 8...
9U3384 ROLLER AS
613C II, 613G, 65C, 65E, 75C, 75D, 75E, 85C, 85D, 85E, 95E
8E3131 ROLLER-CAM
45, 55, D6N, D6T, D8N, D8R, D8R II, D9R
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.