1186528 ROLLER AR-TRACK CARRIER Caterpillar parts
D10R, D10T
Rating:
Alternative (cross code) number:
CA1186528
118-6528
1186528
CA1186528
118-6528
1186528
TRACK-TYPE TRACTOR,
Information:
Two short jumper wires are needed to check the continuity of some wiring harness circuits by shorting two adjacent terminals together in a connector. A long extension wire may also be needed to check the continuity of some wiring harness circuits.
Table 2
Jumper Wires    
No. of Wires     Wire Size     Length of Wire    
2 (1)     16 AWG     203 mm (8 inch)    
2 (1)     16 AWG    
1.2 m (4 ft)    
( 1 ) Use the 1U-5804 Crimp Tool to crimp pins on one wire and sockets on the other wire. Electronic Service Tool
The electronic service tool may display the following information:
Parameters
Event codes
Diagnostic codes
Engine configurationThe electronic service tool may be used by the technician to perform the following functions:
Diagnostic tests
Sensor calibrations
Flash programming
Set parametersThe following components are required to use the electronic service tool to service the engine.
Table 3
Required Tools for the Use of The Electronic Service Tool    
Part Number    Description    
JERD2124     "Electronic Technician Program"    
JERD2129     "Data Subscription for All Engines and Machines"    Connecting The Electronic Service Tool and the Communications Adapter
Illustration 1 g00647144
Communication Adapter II (1) Personal computer (PC) (2) 196-0055 Adapter Cable (PC Serial) (3) 171-4401 Communication Adapter II (4) 207-6845 Data Link Cable As (Data Link)Note: Items (2), (3), and (4) are part of the 171-4400 Communication Adapter II Gp .Use the following procedure to connect the electronic service tool.
Turn the keyswitch to the OFF/RESET position.
Connect cable (2) between the "COMPUTER" end of communication adapter (3) and the RS232 serial port of PC (1) .
Connect cable (4) between the "DATA LINK" end of communication adapter (3) and the service tool connector.
Turn the keyswitch to the ON position. If the electronic service tool and the communication adapter do not communicate with the ECM, refer to Troubleshooting, "Electronic Service Tool Will Not Communicate With ECM".Support
For authorization and ordering information, contact Caterpillar Media and Product Information Logistics.Phone: (800) 566-7782, (309) 266-0942Facsimile: (309) 494-1345, 309-494-1348E-mail: media_logisticsHours: 7:30 AM to 4:30 PM (CST)If you are having problems with the software, you can contact the Caterpillar Service Systems Support Center.Phone: (800) 765-0999, (309) 675-4000Facsimile: (309) 675-4001E-mail: dcsghlpHours: 6:00 AM to 6:00 PM (CST)Optional Service Tools
The following table contains service tools that may be helpful to service the engine, but these tools are not required.
Table 4
Optional Service Tools    
Part Number    Description    
4C-4075     Crimp Tool (4-10 AWG)    
4C-4911 (1)     Battery Load Tester    
5P-7277     Voltage Tester    
8T-5319     Connector Tool Gp    
( 1 ) Refer to Special Instructions, SEHS9249, "Use of the 4C-4911 Battery Load Tester for 6, 8, and 12 Volt Lead Acid Batteries" and Special Instructions, SEHS7633, "Battery Test Procedure".Publications
Table 5
Publications That Will Be Needed in the Installation    
Description     Form Number    
"EMS Operators Guide"     LEKM7488    Note: Refer to the following information that may be specific to the particular industrial application:
Wiring Schematic for the Engine
Engine
Table 2
Jumper Wires    
No. of Wires     Wire Size     Length of Wire    
2 (1)     16 AWG     203 mm (8 inch)    
2 (1)     16 AWG    
1.2 m (4 ft)    
( 1 ) Use the 1U-5804 Crimp Tool to crimp pins on one wire and sockets on the other wire. Electronic Service Tool
The electronic service tool may display the following information:
Parameters
Event codes
Diagnostic codes
Engine configurationThe electronic service tool may be used by the technician to perform the following functions:
Diagnostic tests
Sensor calibrations
Flash programming
Set parametersThe following components are required to use the electronic service tool to service the engine.
Table 3
Required Tools for the Use of The Electronic Service Tool    
Part Number    Description    
JERD2124     "Electronic Technician Program"    
JERD2129     "Data Subscription for All Engines and Machines"    Connecting The Electronic Service Tool and the Communications Adapter
Illustration 1 g00647144
Communication Adapter II (1) Personal computer (PC) (2) 196-0055 Adapter Cable (PC Serial) (3) 171-4401 Communication Adapter II (4) 207-6845 Data Link Cable As (Data Link)Note: Items (2), (3), and (4) are part of the 171-4400 Communication Adapter II Gp .Use the following procedure to connect the electronic service tool.
Turn the keyswitch to the OFF/RESET position.
Connect cable (2) between the "COMPUTER" end of communication adapter (3) and the RS232 serial port of PC (1) .
Connect cable (4) between the "DATA LINK" end of communication adapter (3) and the service tool connector.
Turn the keyswitch to the ON position. If the electronic service tool and the communication adapter do not communicate with the ECM, refer to Troubleshooting, "Electronic Service Tool Will Not Communicate With ECM".Support
For authorization and ordering information, contact Caterpillar Media and Product Information Logistics.Phone: (800) 566-7782, (309) 266-0942Facsimile: (309) 494-1345, 309-494-1348E-mail: media_logisticsHours: 7:30 AM to 4:30 PM (CST)If you are having problems with the software, you can contact the Caterpillar Service Systems Support Center.Phone: (800) 765-0999, (309) 675-4000Facsimile: (309) 675-4001E-mail: dcsghlpHours: 6:00 AM to 6:00 PM (CST)Optional Service Tools
The following table contains service tools that may be helpful to service the engine, but these tools are not required.
Table 4
Optional Service Tools    
Part Number    Description    
4C-4075     Crimp Tool (4-10 AWG)    
4C-4911 (1)     Battery Load Tester    
5P-7277     Voltage Tester    
8T-5319     Connector Tool Gp    
( 1 ) Refer to Special Instructions, SEHS9249, "Use of the 4C-4911 Battery Load Tester for 6, 8, and 12 Volt Lead Acid Batteries" and Special Instructions, SEHS7633, "Battery Test Procedure".Publications
Table 5
Publications That Will Be Needed in the Installation    
Description     Form Number    
"EMS Operators Guide"     LEKM7488    Note: Refer to the following information that may be specific to the particular industrial application:
Wiring Schematic for the Engine
Engine
Caterpillar SIS machinery equipment:
Caterpillar SIS
D10R Custom Parts Manual Track-Type Tractor 3KR00001-UP (MACHINE) »
118-6528
ROLLER AR-TRACK CARRIER
D10R CUSTOM PARTS MANUAL TRACK-TYPE TRACTOR AKT00001-UP (MACHINE) POWERED BY 3412E Engine »
118-6528
ROLLER AR-TRACK CARRIER
D10T TRACK-TYPE TRACTOR RJG00001-UP (MACHINE) POWERED BY C27 Engine »
118-6528
ROLLER AR-TRACK CARRIER
Parts roller Caterpillar catalog:
1955855
ROLLER GP-TRACK-SINGLE FLANGE
D10N, D10R, D10T
D10N, D10R, D10T
1955856
ROLLER GP-TRACK-DOUBLE FLANGE
D10N, D10R, D10T
D10N, D10R, D10T
3599904
ROLLER GP-TRACK CARRIER
D10T, D10T2
D10T, D10T2
3854710
ROLLER GP-TRACK CARRIER
D10T, D10T2
D10T, D10T2
3326424
ROLLER GP-TRACK-DOUBLE FLANGE
D10T, D10T2
D10T, D10T2
8Y6064
ROLLER-SLIDER
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
8Y6060
ROLLER
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
1S9110
ROLLER AS
120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 160G, 160H, 160H ES, 160H NA, 160K,...
120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 160G, 160H, 160H ES, 160H NA, 160K,...
1955853
ROLLER & BEARING AS
D10N, D10R, D10T
D10N, D10R, D10T
3097677
ROLLER & BEARING AS
D10N, D10R, D10T, D10T2
D10N, D10R, D10T, D10T2
1955854
ROLLER & BEARING AS
D10N, D10R, D10T
D10N, D10R, D10T
3703825
ROLLER GP-TRACK-DOUBLE FLANGE
D6K LGP, D6K2, D6K2 LGP, PL61
D6K LGP, D6K2, D6K2 LGP, PL61
1977637
ROLLER GP-TRACK-SINGLE FLANGE
583R, D8R, D8R II
583R, D8R, D8R II
3326423
ROLLER GP-TRACK-SINGLE FLANGE
D10T, D10T2
D10T, D10T2
2495554
ROLLER GP-TRACK
DEUCE
DEUCE
1438676
ROLLER GP-TRACK
45, 55
45, 55
1028120
ROLLER AR-TRACK & CARRIER
311C, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 317, OEMS
311C, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 317, OEMS
1327928
ROLLER GP-TRACK-SINGLE FLANGE
583R, D8R, D8R II
583R, D8R, D8R II
4502953
ROLLER GP-FEED
SAT22DB, SAT322
SAT22DB, SAT322
2979167
ROLLER AR-TRACK & CARRIER
345D L, 349D L, 349E
345D L, 349D L, 349E