AVSPARE.COM
parts catalog

ROLLER & BEARING AS 1969956 - Caterpillar


1969956 ROLLER & BEARING AS Caterpillar parts D9R, D9T
Rating:
36
Alternative (cross code) number:
CA1969956
196-9956
1969956
Caterpillar 1969956 ROLLER & BEARING AS
Weight: 170 pounds 77 kg.

Buy ROLLER & BEARING AS 1969956 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 1969956:

TRACK-TYPE TRACTOR  D9R   D9T   Caterpillar
Number on catalog scheme: 9
  For full view, you need register

Information:


Illustration 1 g01266427
Machine Control ECM 10 VDC Sensor Power Supply connectionsThis diagnostic code is associated with the Machine Control ECM 10 volt sensor power supply. The 10 volt sensor power supply provides power for the left hand and the right hand thumbwheel position sensors (attachments). The thumbwheel sensors are located in the left hand joystick and the right hand joystick.The CID 1482 FMI 03 diagnostic code is activated when the Machine Control ECM detects that the voltage of the 10 volt power supply circuit is above normal.The following conditions could cause this diagnostic code:
The power supply circuit is shorted to a higher voltage source.
A sensor has failed.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the problem has been corrected. Verify that the CID 1482 FMI 03 is active before performing this procedure.Test Step 1. CHECK THE VOLTAGE AT THE SENSOR
Turn the disconnect switch and the key switch to the ON position.
At the left hand joystick or the right hand joystick, locate the three contact machine harness connector for the thumbwheel position sensor (if equipped). Insert a 7X-1710 Multimeter Probe along the supply wire E472-GN at contact A. Insert a 7X-1710 Multimeter Probe along the return wire J766-PU at contact B(left joystick) or the return wire J767-GY (right joystick).
Measure the voltage between the supply contact A and the return contact B.Expected Result:The voltage measurement is 10.0 0.4 DCV.Results:
OK - The voltage measurement is 10.0 0.4 DCV. The voltage is correct. Proceed to Test Step 4.
NOT OK - The voltage measurement is greater than 10.0 0.4 DCV. The voltage measurement is not correct. Proceed to Test Step 2.Test Step 2. CHECK THE POWER SUPPLY AT THE ECM
Turn the disconnect switch and the key switch to the OFF position.
At the Machine Control ECM connector J1, use a 151-6320 Removal Tool or a similar tool to remove the power supply wire and socket at contact J1-69 (wire E472-GN) and one of the return wires and socket at contact J1-70 (wire J766-PU) from the connector. The machine harness connector J1 remains connected to the ECM.
Turn the disconnect switch and the key switch to the ON position.
Use the multimeter probes in order to make contact on the ECM connector pins. Measure the voltage at the ECM pins between the power supply contact J1-69 and the return contact J1-70.Expected Result:The voltage measurement is 10.0 0.4 DCV.Results:
OK - The voltage measurement is 10.0 0.4 DCV. The voltage is correct. The ECM power supply is correct. Install the wires and sockets that were removed from the J1 connector back into their original locations. Proceed to Test Step 3.
NOT OK - The voltage measurement is greater than 10.0 0.3 DCV. The ECM power supply is not correct.Repair: It is unlikely that the ECM has failed. Verify that all possible causes of the diagnostic code have been investigated. Exit this procedure and perform this procedure

Caterpillar parts catalog:

Caterpillar parts catalog
D9R Track-Type Tractor HWH00001-UP (MACHINE) POWERED BY 3408C Engine
DV232 Track Type Tractor NJH00001-UP (MACHINE) POWERED BY C18 Engine
D9R CUSTOM PARTS MANUAL ABK00001-UP (MACHINE)
D9R Track-Type Tractor Power Shift 8BL00001-00829 (MACHINE) POWERED BY 3408 Engine
D9R Track-Type Tractor Power Shift 8BL00830-01052 (MACHINE) POWERED BY 3408 Engine
D9R Track-Type Tractor Power Shift 8BL01053-UP (MACHINE) POWERED BY 3408 Engine
D9R Track-Type Tractor Differential Steering ABK00001-UP (MACHINE) POWERED BY 3408 Engine
D9R Track-Type Tractor Power Shift ACL00001-UP (MACHINE) POWERED BY 3408 Engine
D9R TRACK-TYPE TRACTOR JJB00001-UP (MACHINE) POWERED BY 3408C Engine
D9T Track-Type Tractor RJS00001-UP (MACHINE) POWERED BY C18 Engine
D9R TRACK-TYPE TRACTOR WDM00001-UP (MACHINE) POWERED BY 3408C Engine
D9T TRACK-TYPE TRACTOR TWG00001-UP (MACHINE) POWERED BY C18 Engine
D9T TRACK-TYPE TRACTOR REX00001-UP (MACHINE) POWERED BY C18 Engine


Parts roller Caterpillar catalog:

8H9182 ROLLER-GOVERNOR CONTROL
517, 527, 561B, 561C, 561D, 561M, 571G, 572G, 572R, 578, 583K, 583R, 587R, 589, 931B, 931C, 933, 935B, 939, 941, 950, 955H, 955L, 977H, 977K, 977L, 983, 983B, D10, D10N, D11N, D3, D4D, D4E, D4E SR, D4...
1S9110 ROLLER AS
120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 160G, 160H, 160H ES, 160H NA, 160K,...
1262459 ROLLER BEARING
D6T, D7R, D7R II, D8R, D8R II, D9R
1T1410 ROLLER-FREEWHEEL
24H, 24M, 641B, 651E, 657E, 657G, 69D, 735, 735B, 740, 740B, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772B, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F,...
1262464 ROLLER BEARING
D7R, D7R II, D8R, D8R II, D9R
8E0178 ROLLER
517, 527, D4HTSK II, D4HTSK III, D5HTSK II
8E0181 ROLLER
517, 527, D4HTSK II, D4HTSK III, D5HTSK II
3097677 ROLLER & BEARING AS
D10N, D10R, D10T, D10T2
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.