3004544 ROLLER & BEARING AS Caterpillar parts
312D, 323D SA, 323E L, 325C, 325D, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330B L, 330C, 330C L, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 33...
Rating:
Alternative (cross code) number:
CA3004544
300-4544
3004544
CA3004544
300-4544
3004544
Weight: 45 pounds 20 kg.
EXCAVATOR, UNDERCARRIAGE,
Compatible equipment models: 3004544:
Number on catalog scheme:
3
For full view, you need register
Information:
Remove Cylinder Head Assembly
START BY:a. remove rocker shaft assemblies and push rodsb. remove water temperature regulator (industrial engine)c. remove aftercooler housingd. remove fuel injection linese. remove exhaust manifold 1. Remove bolts (1) from the alternator bracket (if equipped).2. Remove the bolts that hold plate (3), and remove the plate.3. Disconnect water line (2) from the air compressor (if equipped). Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 4. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.5. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb.).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
6. Remove the gasket and seals from the spacer plate.Install Cylinder Head Assembly
Be sure a new gasket has been installed between the spacer plate and the cylinder block. See Remove And Install Spacer Plate. 1. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (1) and two O-ring seals (2). 2. Fasten a hoist, and put cylinder head assembly (3) in position on the cylinder block.3. Put clean engine oil on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown in illustration A87019X1 on page 158.a. Tighten bolts 1 through 20 in number sequence to a torque of 270 25 N m (200 20 lb.ft.).b. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).c. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.d. Install the rocker shaft assemblies and push rods. See Install Rocker Shaft Assemblies And Push Rods.e. Tighten bolts 21 through 26 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).f. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).g. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.h. Tighten the 3/8" bolts to a torque of 43 7 N m (32 5 lb.ft.). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 4 N m (18 3 lb.ft.).4. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in.) for intake and 0.76 mm (.030 in.) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb.ft.).5. Install the valve cover bases and the inner fuel lines. See Install Rocker Shaft Assemblies And Push Rods.6. Install the valve covers. See
START BY:a. remove rocker shaft assemblies and push rodsb. remove water temperature regulator (industrial engine)c. remove aftercooler housingd. remove fuel injection linese. remove exhaust manifold 1. Remove bolts (1) from the alternator bracket (if equipped).2. Remove the bolts that hold plate (3), and remove the plate.3. Disconnect water line (2) from the air compressor (if equipped). Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 4. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.5. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb.).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
6. Remove the gasket and seals from the spacer plate.Install Cylinder Head Assembly
Be sure a new gasket has been installed between the spacer plate and the cylinder block. See Remove And Install Spacer Plate. 1. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (1) and two O-ring seals (2). 2. Fasten a hoist, and put cylinder head assembly (3) in position on the cylinder block.3. Put clean engine oil on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown in illustration A87019X1 on page 158.a. Tighten bolts 1 through 20 in number sequence to a torque of 270 25 N m (200 20 lb.ft.).b. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).c. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.d. Install the rocker shaft assemblies and push rods. See Install Rocker Shaft Assemblies And Push Rods.e. Tighten bolts 21 through 26 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).f. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).g. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.h. Tighten the 3/8" bolts to a torque of 43 7 N m (32 5 lb.ft.). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 4 N m (18 3 lb.ft.).4. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in.) for intake and 0.76 mm (.030 in.) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb.ft.).5. Install the valve cover bases and the inner fuel lines. See Install Rocker Shaft Assemblies And Push Rods.6. Install the valve covers. See
Cat SIS web machinery list:
Parts roller Caterpillar catalog:
1290T, 2491, 2590, 312D, 328D LCR, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F...
311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 323D LN, E110B, E120B
311C, 312, 315B, 315B FM L, 315B L, 315C, 315D L, 317, 317B LN, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320B, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D ...
330C, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 365C L
320 L, 320B, 320C, 323D LN, 323D SA, 325, 325 FM L, 325 L, 325 LN, 325B, 325B L, 325C, 325C L, 325D, 325D L, 325D MH, 328D LCR, 329D, 329D L, 329D LN, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L,...
311, 311B, 311C, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B FM LL, 320B L, 32...
330B L, OEMS
330, 330 L, 330B L, OEMS
320B, 322B L, 322C, 322C FM, 325B, 325B L, 325C, 325C FM, 325C L, 330C, 330D, 330D L, 336D L, 336D LN, 345D, OEMS
330B L, OEMS
325C, 325D FM, 325D FM LL, 330B, 330B L, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 340D L, 340D2 L, 568 FM LL, OEMS
3335609
ROLLER & BEARING AS
306, 306E
306, 306E
3605865
ROLLER & BEARING AS
313D2 LGP, 315D L, 316E L, 318D L, 318D2 L, 318E L, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D2, 320D2 GC, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D2 L, 325D, 329D ...
313D2 LGP, 315D L, 316E L, 318D L, 318D2 L, 318E L, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D2, 320D2 GC, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D2 L, 325D, 329D ...
3095733
ROLLER
311D LRR, 312D, 312D L, 315D L, 319D L, 319D LN, 345D, 345D L, 345D L VG, 349D, 349D L, 374D L, 390D, 390D L
311D LRR, 312D, 312D L, 315D L, 319D L, 319D LN, 345D, 345D L, 345D L VG, 349D, 349D L, 374D L, 390D, 390D L
2799084
ROLLER & BEARING AS
304C CR, 305.5D, 305.5E, 305C CR, 305D CR, 305E
304C CR, 305.5D, 305.5E, 305C CR, 305D CR, 305E
2743534
ROLLER
305.5, 305.5E, 306, 306E
305.5, 305.5E, 306, 306E
2348952
ROLLER & BEARING AS
302.5C
302.5C
3792885
ROLLER AS
301.4C, 301.7D, 301.7D CR, 302.2D, 302.4D
301.4C, 301.7D, 301.7D CR, 302.2D, 302.4D
301.4C, 301.7D, 301.7D CR, 302.2D
3725958
ROLLER GP
300.9D
300.9D
312D, 312D L, 312E, 312E L, 315D L, 316E L, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324E, 32...
3717144
ROLLER
312D, 312D2 GC, 313D, 313D2, 313D2 LGP, 315D L, 318D L, 318D2 L, 320D, 320D FM, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L, 324D, 326D L, 329D, 329D L, 336D, 336D L, 336D2, 340D L, 340...
312D, 312D2 GC, 313D, 313D2, 313D2 LGP, 315D L, 318D L, 318D2 L, 320D, 320D FM, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L, 324D, 326D L, 329D, 329D L, 336D, 336D L, 336D2, 340D L, 340...
1832875
ROLLER & BEARING AS
1290T, 2491, 2590, 312D, 328D LCR, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F...
1290T, 2491, 2590, 312D, 328D LCR, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F...