AVSPARE.COM
parts catalog

ROLLER GP-FEED 4415987 - Caterpillar



4415987 ROLLER GP-FEED Caterpillar parts SAT318T, SAT322 ROLLER
Rating:
76
Alternative (cross code) number:
CA4415987
441-5987
4415987
Caterpillar 4415987 ROLLER GP-FEED

Buy ROLLER GP-FEED 4415987 Caterpillar genuine, new aftermarket tractor parts with delivery
HARVESTER HEAD,

Compatible equipment models: 4415987:

HARVESTER HEAD  SAT318T   SAT322   Caterpillar
Number on catalog scheme: 25
  
  For full view, you need register

Information:


Illustration 12 g01123198
Install Tooling (C) on the front housing. Do not tighten the bolts on Tooling (C). Note: Tooling (C) can be installed on the flywheel housing in order to install the camshaft from the rear of the engine.
Install Tooling (B) on the ends of the camshaft. Install Tooling (D) on Tooling (B) which is installed on the front of the camshaft.
Ensure that the camshaft and the camshaft bearings are clean. Place clean engine oil on the lobes and the journals of the camshaft. Also place clean engine oil on the camshaft bearings.
Rotate the camshaft and insert the camshaft into the engine. Position the camshaft in the engine until Tooling (B) is in the front camshaft bearing. Rotate the camshaft in order to align Tooling (C) and the camshaft bores. Tighten the bolts for Tooling (C).
Rotate the camshaft and insert the camshaft into the engine. Remove Tooling (D) from Tooling (B). Remove Tooling (B) from the camshaft. Remove Tooling (C) from the front housing.
Illustration 13 g01122334
Install thrust washer (10) and bolts (11).
Install bolts (12).
If the camshaft is out of time more than 18 degrees (approximately 1/2 of the timing pin is out of the groove), the valves can make contact with the pistons. This will cause damage to the engine. Refer to Testing and Adjusting, "Camshaft Timing" for more information.
Illustration 14 g01122583
Remove timing plate (15) from the storage position under the rear camshaft cover.
Turn the camshaft until the timing pin can be installed through the cylinder block and into the groove that is in the camshaft. Refer to Testing and Adjusting, "Camshaft Timing" for more information.
Illustration 15 g01123337
Remove bolts (17), cover (16), and plug (18) from flywheel housing (19).
Install one bolt (17) into the flywheel housing through the hole for plug (18). Use Tooling (E) and a ratchet to turn the flywheel until bolt (17) can be installed through the hole and into the flywheel. Doing so will position the No. 1 cylinder at the top center. Refer to Testing and Adjusting, "Finding the Top Center Position for the No. 1 Piston" for more information.
Illustration 16 g01123380
Use the following procedure in order to install camshaft drive gear (8).
Clean the taper of the camshaft and the tapered bore of the camshaft gear with a lint free cloth saturated with solvent to remove oil. Clean the parts again with a lint free alcohol wipe in order to remove any residue. The the alcohol wipe will dirty after cleaning the parts. Clean the parts again with a lint free alcohol wipe until no residue is left on the alcohol wipe. Note: The camshaft and the tapered bore of the camshaft gear must be clean, dry, and free of residue before assembly.
Ensure that the camshaft timing pins and the timing pin for the flywheel are installed.
Place camshaft drive gear (8) in position. Remove the backlash by rotating the gears in the opposite direction of camshaft rotation. Note: For "Standard Rotation" engines, turn the camshaft drive gears COUNTERCLOCKWISE. For "Reverse Rotation" engines, turn the camshaft drive gears CLOCKWISE.
Install

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
SAT318T HARVESTER HEAD HH700001-UP (MACHINE)
SAT318T SC HARVESTER HEAD HH200001-UP (MACHINE)
SAT322T SC HARVESTER HEAD SHM00001-UP (MACHINE)
SAT322T HARVESTER HEAD SHF00001-UP (MACHINE)
SAT323T HARVESTER HEAD SH900001-UP (MACHINE)
SAT323T SC HARVESTER HEAD SHG00001-UP (MACHINE)


Parts roller Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.