4U4924 ROOF COVER Caterpillar parts
D25C, D30C, D350C, D35C, D35HP, D400
Rating:
Alternative (cross code) number:
CA4U4924
4U-4924
4U4924
CA4U4924
4U-4924
4U4924
Weight: 16 pounds 7 kg.
ARTICULATED TRUCK,
Number on catalog scheme:
None
For full view, you need register
Information:
Installation Procedure for the Electrical Components
Lay out the wiring harnesses, 173-3714 Wiring Harness (Long) and 173-3713 Wiring Harness (Short) .
Illustration 27 g00677962
Preferred location of the switch
Illustration 28 g00677967
Alternate location of switchNote: If you use the alternate location for the B-series, use a second 172-4478 Plate with the switch.
Duplicate the template in Illustration 35 in order to locate the holes. Remove the console. Fasten the template to the console. Determine the position of the 7N-2353 Switch on the console. Drill a 12 mm (0.469 inch) hole in the console. Drill a 3.0 mm (0.125 inch) hole for the second hole. Place the 7N-2353 Switch in the 172-4478 Plate . Install the plate and the switch into the hole in the console.
Illustration 29 g00678430
Illustration 30 g00613189
Connect the wiring harness to the toggle switch. Connect the green wire to the terminal that is identified by the number 3. Connect the yellow wire to the terminal that is identified by the number 2. Refer to Illustration 29.
Illustration 31 g00678467
Connect the yellow wire from the toggle switch to the relay terminal of the start switch.
Illustration 32 g00613310
Install the 6V-1574 Grommet into the hole that is located on the floor in the right rear corner of the cab. Run the wire from the cab, through the grommet, and back to the valve. Use nylon ties to fasten the wiring harness to the existing wiring harness.
Connect the green wire to the valve. In order to ground the wiring harness, connect the black wire to a mounting bolt of the valve. There is a ring terminal that is installed on the black wire.Check the System
After the electrical system and the hydraulic system are connected, check the system for proper operation. Refer to the Operation and Maintenance Manual, SEBU7304 for more information.
Purge the hydraulic system of air. Refer to Operation and Maintenance Manual, SEBU7304, "Hydraulic System Air - Purge".Schematics
Illustration 33 g00678652
Hydraulic schematic (1) Upper pump (2) Upper pump pressure port (3) Fluid sampling valve (4) Quick coupler (5) Valve assembly (6) Drain port
Illustration 34 g00679442
Electrical schematic (1) Switch (2) Solenoid (3) Diode (4) AlarmTemplate
Illustration 35 g01366798
Template for switch
Lay out the wiring harnesses, 173-3714 Wiring Harness (Long) and 173-3713 Wiring Harness (Short) .
Illustration 27 g00677962
Preferred location of the switch
Illustration 28 g00677967
Alternate location of switchNote: If you use the alternate location for the B-series, use a second 172-4478 Plate with the switch.
Duplicate the template in Illustration 35 in order to locate the holes. Remove the console. Fasten the template to the console. Determine the position of the 7N-2353 Switch on the console. Drill a 12 mm (0.469 inch) hole in the console. Drill a 3.0 mm (0.125 inch) hole for the second hole. Place the 7N-2353 Switch in the 172-4478 Plate . Install the plate and the switch into the hole in the console.
Illustration 29 g00678430
Illustration 30 g00613189
Connect the wiring harness to the toggle switch. Connect the green wire to the terminal that is identified by the number 3. Connect the yellow wire to the terminal that is identified by the number 2. Refer to Illustration 29.
Illustration 31 g00678467
Connect the yellow wire from the toggle switch to the relay terminal of the start switch.
Illustration 32 g00613310
Install the 6V-1574 Grommet into the hole that is located on the floor in the right rear corner of the cab. Run the wire from the cab, through the grommet, and back to the valve. Use nylon ties to fasten the wiring harness to the existing wiring harness.
Connect the green wire to the valve. In order to ground the wiring harness, connect the black wire to a mounting bolt of the valve. There is a ring terminal that is installed on the black wire.Check the System
After the electrical system and the hydraulic system are connected, check the system for proper operation. Refer to the Operation and Maintenance Manual, SEBU7304 for more information.
Purge the hydraulic system of air. Refer to Operation and Maintenance Manual, SEBU7304, "Hydraulic System Air - Purge".Schematics
Illustration 33 g00678652
Hydraulic schematic (1) Upper pump (2) Upper pump pressure port (3) Fluid sampling valve (4) Quick coupler (5) Valve assembly (6) Drain port
Illustration 34 g00679442
Electrical schematic (1) Switch (2) Solenoid (3) Diode (4) AlarmTemplate
Illustration 35 g01366798
Template for switch
Caterpillar parts catalog:
Parts roof Caterpillar catalog:
5U4274
ROOF PANEL
D25C, D30C, D350C, D35C, D35HP, D400
D25C, D30C, D350C, D35C, D35HP, D400
5U5274
ROOF COVER ASSEMBLY
D25C, D30C, D350C, D35C, D35HP, D400
D25C, D30C, D350C, D35C, D35HP, D400
8D5621
ROOF AS
773B, 777
773B, 777
2623886
ROOF AS
785B, 789B, 793B
785B, 789B, 793B
4361220
ROOF AS
966M XE, 972M XE
966M XE, 972M XE
3587862
ROOF
950 GC, 966M, 966M XE, 972M, 972M XE, 980M, 982M
950 GC, 966M, 966M XE, 972M, 972M XE, 980M, 982M
2177272
ROOF
554, 564, 574B
554, 564, 574B
1G2645
ROOF
PS-300
PS-300
5E7480
ROOF AS
CB-521
CB-521
0846522
ROOF
PS-500
PS-500
1368493
ROOF
CB-534B
CB-534B
4U5988
ROOF COVER
D25C, D30C, D350C, D35C, D35HP, D400
D25C, D30C, D350C, D35C, D35HP, D400