5142933 ROPE AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA5142933
514-2933
5142933
CA5142933
514-2933
5142933
Weight: 57 pounds 25 kg.
Information:
Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the interim corrective action that is identified below.Problem
Wiring harnesses are not available to order for a direct installation of PL542 on the machines listed above.Solution
Follow the procedure outlined below to install the PL542 wiring until parts are available for a direct installation.
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility.
Illustration 1 g06258799
Locate the Product Link plug on the back of the cab as shown in Illustration 1.
Illustration 2 g06258802
9 pin 510-4065 Cable As
Illustration 3 g06258805
14 pin 510-4063 Cable As
Remove the 9 pin or 14 pin connector from the cable assembly shown in Illustrations 2 and 3.
Illustration 4 g06258807
Remove the grommet from the B-pillar and feed the PL cable assembly through. Replace and seal the grommet where it passes through the cab as shown in Illustration 4.
Illustration 5 g06258809
Illustration 6 g06258812
Attach a 12-pin male Deutsch connector to the PL cable assembly where the 9 or 14 pin connector was removed in Step 2. Install the pins into the Deutsch connector as shown in Illustrations 5 and 6.
Illustration 7 g06258816
(A) PL542 module
(B) PL542 warning decal
Write down the PL542 serial number for software verification. Using double sided tape, install the PL542 module (A) facing upward on the back deck of the cab next to the right hand B-pillar. Install the PL542 warning decal (B) on the glass above the module.
Ensure the latest software (541-6385 or above) is installed on PL542.Note: PL542 will need to be reflashed if the software is not 541-6385 or above. Submit a Dealer Solution Network (DSN) System Technology inquiry to the telematics group and request an over the air flash of PL542. PL542 can only be flashed over the air at this time.
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the interim corrective action that is identified below.Problem
Wiring harnesses are not available to order for a direct installation of PL542 on the machines listed above.Solution
Follow the procedure outlined below to install the PL542 wiring until parts are available for a direct installation.
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility.
Illustration 1 g06258799
Locate the Product Link plug on the back of the cab as shown in Illustration 1.
Illustration 2 g06258802
9 pin 510-4065 Cable As
Illustration 3 g06258805
14 pin 510-4063 Cable As
Remove the 9 pin or 14 pin connector from the cable assembly shown in Illustrations 2 and 3.
Illustration 4 g06258807
Remove the grommet from the B-pillar and feed the PL cable assembly through. Replace and seal the grommet where it passes through the cab as shown in Illustration 4.
Illustration 5 g06258809
Illustration 6 g06258812
Attach a 12-pin male Deutsch connector to the PL cable assembly where the 9 or 14 pin connector was removed in Step 2. Install the pins into the Deutsch connector as shown in Illustrations 5 and 6.
Illustration 7 g06258816
(A) PL542 module
(B) PL542 warning decal
Write down the PL542 serial number for software verification. Using double sided tape, install the PL542 module (A) facing upward on the back deck of the cab next to the right hand B-pillar. Install the PL542 warning decal (B) on the glass above the module.
Ensure the latest software (541-6385 or above) is installed on PL542.Note: PL542 will need to be reflashed if the software is not 541-6385 or above. Submit a Dealer Solution Network (DSN) System Technology inquiry to the telematics group and request an over the air flash of PL542. PL542 can only be flashed over the air at this time.
Parts rope Caterpillar catalog:
5142931
ROPE AS
Caterpillar
Caterpillar
5120906
ROPE AS
Caterpillar
Caterpillar
5120905
ROPE AS
Caterpillar
Caterpillar
5120904
ROPE AS
Caterpillar
Caterpillar
5100625
ROPE AS
Caterpillar
Caterpillar
5087914
ROPE-WIRE
Caterpillar
Caterpillar
5258652
ROPE AS
Caterpillar
Caterpillar
5214811
ROPE GP
Caterpillar
Caterpillar
5175631
ROPE AS
Caterpillar
Caterpillar
5157095
ROPE-SWITCH
Caterpillar
Caterpillar
5144085
ROPE GP
Caterpillar
Caterpillar
5142938
ROPE AS
Caterpillar
Caterpillar