AVSPARE.COM
parts catalog

SCRAPER AR 4415700 - Caterpillar



4415700 SCRAPER AR Caterpillar parts 623K, 623K LRC SCRAPER
Rating:
21
Alternative (cross code) number:
CA4415700
441-5700
4415700
Caterpillar 4415700 SCRAPER AR

Buy SCRAPER AR 4415700 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL TRACTOR-SCRAPER,

Compatible equipment models: 4415700:

WHEEL TRACTOR-SCRAPER  623K   623K LRC   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

A4:E4 Engine ECM and A5:E2 Aftertreatment ECM Replacement
If the flash file and engine application are not matched, engine damage may result.
Perform the following procedure in order to replace the A4:E4 Engine ECM and A5:E2 Aftertreatment ECM.
Record the configuration data.
Try to establish communication between the Caterpillar Electronic Technician (ET) and the ECM. Proceed to Test Step 2 if Cat ET does not communicate with the ECM.
Print the parameters from the "Configuration" screen on Cat ET. If a printer is unavailable, record all of the parameters.
Obtain the customer passwords from the vehicle owner. Access the customer specified parameters with Cat ET. Record the value of each customer parameter.
Record ECM lifetime totals.________
Record any logged diagnostic codes. ________Note: If the customer passwords are not available proceed to Troubleshooting, "Customer Passwords" for details that are related to customer passwords.
Use the "Copy Configuration/ECM Replacement" feature that is found under the "Service" menu on Cat ET. Select "Load from ECM" in order to copy the configuration data from the suspect ECM.Note: If the "Copy Configuration" process fails, the parameters must be obtained elsewhere. Some of the system configuration parameters are stamped on the engine information plate. The aftertreatment identification information is stamped on the CEM identification plate. Most of the parameters must be obtained from the factory. Parameters that are related to customer specified parameters must be obtained from the customer or from the Original Equipment Manufacturer (OEM).
Removal of the ECM:
Turn the keyswitch OFF.
Disconnect both ECM connectors.
Disconnect the ECM ground strap.
Remove the mounting hardware at each corner of the ECM.
Installation of the replacement ECM:
Use the old mounting hardware to install the replacement ECM.
Connect the ECM ground strap.
Connect both ECM connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Configure the replacement ECM:
Flash program the latest available flash file into the ECM. Refer to Troubleshooting, "ECM Software - Install" for the correct procedure.
Use Cat ET to match the engine application and the interlock code if the replacement ECM was used for a different application.Note: Two sets of factory passwords are required in order to program the Aftertreatment parameters.
If the "Copy Configuration" process from Step 1.d was successful, return to the "Copy Configuration/ECM Replacement" screen on Cat ET and select "Program ECM". Proceed to Step 4.e when programming is complete.
If the "Copy Configuration" process from Step 1.d was unsuccessful, manually program the ECM parameters. The parameters must match the parameters from Step 1.d.
Program the engine monitoring system, if necessary.
Calibrate the engine speed/timing if there is a diagnostic code for speed/timing sensor calibration. The procedure is in Troubleshooting, "Timing - Calibrate".Note: If an engine is a Series C7.1 or Series C9.3, use Cat ET to perform the "fuel system functional test". This test established a baseline value of the fuel system rate of fuel return at high rail pressure. Other diagnostic codes may be activated if this test is not performed.
If an E1305 (1) or a 3483-11 code becomes active after the ECM replacement, Refer to Troubleshooting, "ARD is Disabled" for instructions on clearing the

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
623K Wheel Tractor-Scraper WTB00001-UP (MACHINE) POWERED BY C13 Engine
623K Wheel Tractor-Scraper WTM00001-UP (MACHINE) POWERED BY C13 Engine


Parts scraper Caterpillar catalog:

3845878 SCRAPER GP-SMOOTH DRUM
CP-54B, CS-54B, CS-56B, CS-64B, CS-66B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.