0994776 SCREEN AS Caterpillar parts
311, E110B, E120B
Rating:
Alternative (cross code) number:
CA0994776
099-4776
0994776
CA0994776
099-4776
0994776
Weight: 1 pounds 0 kg.
EXCAVATOR,
You can buy:
US$53.90
28 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CARTEX Filter Kit 3I-1482 094-7073 094-3229 099-4776 for FITS Caterpillar CAT Excavator E120B
CARTEX Whether you're a professional mechanic or a DIY enthusiast,We've got you covered with a wide range of parts that meet the highest standards of quality and performance. || Order your High Quality Part with peace of mind, knowing we prioritize your satisfaction. Quality Parts, Superior Performance - it's not just a promise, it's our standard || QUESTIONS? : We at CARTEX - High Quality Parts USA has more than 40 years of experience in industry and has in-house technicians, If you are not sure if this part fits your machine or tractor, just send us an email before you make the purchase and our in house technicians will revert back to you, right away.
CARTEX Whether you're a professional mechanic or a DIY enthusiast,We've got you covered with a wide range of parts that meet the highest standards of quality and performance. || Order your High Quality Part with peace of mind, knowing we prioritize your satisfaction. Quality Parts, Superior Performance - it's not just a promise, it's our standard || QUESTIONS? : We at CARTEX - High Quality Parts USA has more than 40 years of experience in industry and has in-house technicians, If you are not sure if this part fits your machine or tractor, just send us an email before you make the purchase and our in house technicians will revert back to you, right away.
ELSOON 099-4776 Hydraulic Filter Compatible with Caterpillar 311 312B E110B E120B Excavator
ELSOON Part Name: Hydraulic Filter || Part Number: 099-4776 || Condition: New || High Quality and Performance || Fit for Caterpillar 311 312B E110B E120B Excavator
ELSOON Part Name: Hydraulic Filter || Part Number: 099-4776 || Condition: New || High Quality and Performance || Fit for Caterpillar 311 312B E110B E120B Excavator
Sogoparts Hydraulic Filter 099-4776 0994776 Compatible with Mitsubishi Engine S4K-T Compatible with Caterpillar Excavator E110B E120B 312-A 311-A 311 312B 311B 312BL Engine 3114 3064
Sogoparts Part Numbers: 099-4776 0994776 CA0994776 ST70857 SH60060 H55350 || Compatible with Mitsubishi Engine S4K-T Compatible with Caterpillar Excavator E110B E120B 312-A 311-A 311 312B 311B 312BL Engine 3114 3064 || Package Includes: 1 x Hydraulic Filter || Easy To Install. Manufactured to Precise OE Requirements For Perfect Fit. Reliable Performance. || Replacement Parts. As Good As OEM at a Fraction of the Price. Exact Same Performance as Original
Sogoparts Part Numbers: 099-4776 0994776 CA0994776 ST70857 SH60060 H55350 || Compatible with Mitsubishi Engine S4K-T Compatible with Caterpillar Excavator E110B E120B 312-A 311-A 311 312B 311B 312BL Engine 3114 3064 || Package Includes: 1 x Hydraulic Filter || Easy To Install. Manufactured to Precise OE Requirements For Perfect Fit. Reliable Performance. || Replacement Parts. As Good As OEM at a Fraction of the Price. Exact Same Performance as Original
This part in 2 request:
Show.
This information for suppliers only!
2025-03-04
2022-03-07
Number on catalog scheme:
26
For full view, you need register
Information:
start by:a) remove cylinder headsb) remove oil pan1. Remove the carbon from the top inside surface of the cylinders with tool (A). 2. Turn the crankshaft until two pistons are at bottom center.3. Remove connecting rod caps (1) from the two connecting rods. Put pieces of rubber hose or tape on the threads of the connecting rod bolts as protection for the crankshaft. 4. Push the pistons and connecting rods away from the crankshaft until the piston rings are above the cylinder block.5. Remove the two pistons (2) and the connecting rods. Keep each connecting rod cap with its respective connecting rod and piston. Put identification on each connecting rod as to its location for use at installation.
Do not turn the crankshaft while any of the connecting rods are in the engine without the caps installed.
6. Do Steps 2 through 5 for the remainder of the pistons.Install Pistons
Two different pistons are used in 3208 Truck Engines. One piston has a crater volume of 50.4 1.3 cm3 (3.08 .07 in.3), and the other piston has a crater volume of 58.8 1.2 cm3 (3.59 .07 in.3). Check the part number stamped on the top of the piston and refer to the parts book to be sure the correct replacement piston is used. The correct piston must be installed in the engine. If the wrong piston is installed, much damage to the engine will be the result.
1. Put clean engine oil on the piston rings, connecting rod bearings, cylinder walls and crankshaft bearing journals.2. Turn the crankshaft until the bearing journal for the pistons to be installed is at bottom center.3. Make sure the piston ring gaps are at least 120° apart on the piston. 4. Use tool (A) and install the piston in position in the same cylinder bore from which it was removed. The hole (crater) in the top of the piston must be toward (nearest) the center of the engine. For more detail about the installation of connecting rod bearings, see REMOVE AND INSTALL CONNECTING ROD BEARINGS.5. Check the bearing clearances with tool (B).6. Put 2P2506 Thread Lubricant on the threads of the bolts and contact surfaces of the nuts for the connecting rod caps.
When the connecting rod caps are installed, make sure that the number on the side of the cap is next to and respective with the number on the side of the connecting rod.
7. Put the cap (1) in position on the connecting rod and install the nuts. Tighten the nuts to a torque of 40 4 N m (30 3 lb.ft.). Put a mark on each nut and the end of each bolt. Tighten the nuts 60 5° more. 8. Check the side clearance between two connecting rods on the same crankshaft journal. Clearance must be 0.08 to 0.84 mm (.003 to .033 in.) for new rods.9. Do Steps 1 through 8 for the remainder of the pistons.end by:a) install cylinder headsb) install oil panDisassemble Pistons
start by:a)
Do not turn the crankshaft while any of the connecting rods are in the engine without the caps installed.
6. Do Steps 2 through 5 for the remainder of the pistons.Install Pistons
Two different pistons are used in 3208 Truck Engines. One piston has a crater volume of 50.4 1.3 cm3 (3.08 .07 in.3), and the other piston has a crater volume of 58.8 1.2 cm3 (3.59 .07 in.3). Check the part number stamped on the top of the piston and refer to the parts book to be sure the correct replacement piston is used. The correct piston must be installed in the engine. If the wrong piston is installed, much damage to the engine will be the result.
1. Put clean engine oil on the piston rings, connecting rod bearings, cylinder walls and crankshaft bearing journals.2. Turn the crankshaft until the bearing journal for the pistons to be installed is at bottom center.3. Make sure the piston ring gaps are at least 120° apart on the piston. 4. Use tool (A) and install the piston in position in the same cylinder bore from which it was removed. The hole (crater) in the top of the piston must be toward (nearest) the center of the engine. For more detail about the installation of connecting rod bearings, see REMOVE AND INSTALL CONNECTING ROD BEARINGS.5. Check the bearing clearances with tool (B).6. Put 2P2506 Thread Lubricant on the threads of the bolts and contact surfaces of the nuts for the connecting rod caps.
When the connecting rod caps are installed, make sure that the number on the side of the cap is next to and respective with the number on the side of the connecting rod.
7. Put the cap (1) in position on the connecting rod and install the nuts. Tighten the nuts to a torque of 40 4 N m (30 3 lb.ft.). Put a mark on each nut and the end of each bolt. Tighten the nuts 60 5° more. 8. Check the side clearance between two connecting rods on the same crankshaft journal. Clearance must be 0.08 to 0.84 mm (.003 to .033 in.) for new rods.9. Do Steps 1 through 8 for the remainder of the pistons.end by:a) install cylinder headsb) install oil panDisassemble Pistons
start by:a)
Caterpillar parts catalog:
Parts screen Caterpillar catalog:
1057450
SCREEN GP-HYDRAULIC
311, 312
311, 312
7E0155
SCREEN AS-FUEL INLET
205B, 211B, 214B, 3114, 3116, 3126, 3126B, 3126E, 446B, 950F, AP-1000, AP-1050, BG-2455C, BG-245C, C7, CB-434, CB-634C, CB-634D, CP-563, CS-531D, CS-533D, CS-563C, CS-573C, CS-583C, E120B, E200B, E240...
205B, 211B, 214B, 3114, 3116, 3126, 3126B, 3126E, 446B, 950F, AP-1000, AP-1050, BG-2455C, BG-245C, C7, CB-434, CB-634C, CB-634D, CP-563, CS-531D, CS-533D, CS-563C, CS-573C, CS-583C, E120B, E200B, E240...
120H, 120H ES, 120H NA, 135H, 135H NA, 211B, 214B, 3114, 3116, 3126, 320B, 322, 322B L, 322B LN, 322C, 322C FM, 325, 325 L, 325B, 325B L, 35, 446, 446B, 446D, 45, 525B, 533, 535B, 539, 543, 55, 550, 5...
214B, 3114, 3116, CB-434, E120B, E200B
311, 311B, 312, 312B
0994700
SCREEN AS
311, 312, 313B, E110B, E120B
311, 312, 313B, E110B, E120B
0855424
SCREEN AS
307, E70B
307, E70B
1189952
SCREEN ASSEM.
311B, 312B
311B, 312B
8U3968
SCREEN-PLATE
206, 212
206, 212
5W1195
SCREEN AS. SUN
205, 206, 212
205, 206, 212
5W2612
SCREEN AS. INTAK
205, 206, 212
205, 206, 212
4Z9266
SCREEN AS
D6R, D6R II
D6R, D6R II
4Z9127
SCREEN AS
D6R, D6R II
D6R, D6R II
4Z8818
SCREEN AS
D6R, D6R II
D6R, D6R II
D6R, D6R II, D6R III, D6R STD, D6T, D7R, D7R II, D7R XR, D9R
1058096
SCREEN
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 315B FM L, 320B FM LL, 320C FM, 322B L, 322C, 322C FM, 325B L, 325C FM, 330B L, 330C FM, 345C, 511, 521, 521B, 522, 522B, 532, 541, 541 2,...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 315B FM L, 320B FM LL, 320C FM, 322B L, 322C, 322C FM, 325B L, 325C FM, 330B L, 330C FM, 345C, 511, 521, 521B, 522, 522B, 532, 541, 541 2,...
0964182
SCREEN AS
315, E200B
315, E200B