0773064 SEAL-O-RING Caterpillar parts
AP-200, AP-200B, CB-534B, CB-534C, CB-535B, CB-634, CB-634C, CP-433B, CP-433C, CP-563, CS-323C, CS-431C, CS-531C, CS-533, CS-533C, CS-563C, CS-573C, CS-583, CS-583C, PM-201, PM-465, PM-565, PM-565B
Rating:
Alternative (cross code) number:
CA0773064
077-3064
0773064
CA0773064
077-3064
0773064
Weight: 0.01 pounds 0 kg.
ASPHALT PAVER, VIBRATORY COMPACTOR,
Compatible equipment models: 0773064:
Number on catalog scheme:
1
For full view, you need register
Information:
Machine ECM
The following is a list of Diagnostic Trouble Codes (DTCs) that are associated with the relays of the machine.
Table 1
Machine ECM (MID 299)
DTC Code Description System Response
781-3 Lighting Relay : Voltage Above Normal Related lighting system will be ON continuously.
781-6 Lighting Relay : Current Above Normal Related lighting system will be ON continuously.
2912-3 Front Wiper Speed Control Relay : Voltage Above Normal Wiper system will not function.
2912-6 Front Wiper Speed Control Relay : Current Above Normal Wiper system will not function.
3634-3 Boom Light Relay : Voltage Above Normal Related lighting system will be ON continuously.
3634-6 Boom Light Relay : Current Above Normal Related lighting system will be ON continuously. Possible Causes for an FMI 3 Diagnostic code are:
The ground wire is open.
The signal wire is permanently open.
The signal wire is permanently closed.
The indicator lamp has failed.
The Switch Panel has failed. This situation is unlikely.Possible Causes for an FMI 6 Diagnostic code are:
A short to ground exists.
The indicator lamp has failed.
The Switch Panel has failed. This situation is unlikely.
Illustration 1 g03448477
Schematic of the relay circuit for the wiper control module
Illustration 2 g02722559
Schematic of the relay circuits associated with the Switch PanelNote: The diagram above is a simplified schematics of the Machine ECM and the Switch Panel connections. The schematic is electrically correct. However, not all of the possible harness connectors are shown. Refer to the latest revision of Electrical Schematic, KENR9677 (316E), Electrical Schematic, KENR9657 (312E), or Electrical Schematic, UENR3189 (318E) for the complete schematic.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that the diagnostic code is active before performing a troubleshooting procedure.
Table 2
Troubleshooting Test Steps Values Results
1. Identify Active FMI Code Associated With Relay Circuit
Code present. FMI 3 diagnostic code, proceed to Test Step 2.
FMI 6 diagnostic code, proceed to Test Step 3.
Begin Process For FMI 3 Troubleshooting HERE
2. Check The Machine Harness For A Short
A. Turn key start switch and disconnect switch OFF.
B. Disconnect harness connection at relay.
C. If relay connected to ECM, disconnect J1 and J2 connectors from ECM. If relay connected to Switch Panel, disconnect all switch panel connectors.
D. Measure resistance of relay signal contact to all J1 and J2 connectors, if relay is wired directly to Machine ECM. If relay is wired directly to switch panel, measure resistance of relay contact to all switch panel connectors.
Each reading greater than 5K Ω. OK - All resistance measurements are greater than 5K Ω.
Proceed to Test Step 5.
NOT OK - One or
The following is a list of Diagnostic Trouble Codes (DTCs) that are associated with the relays of the machine.
Table 1
Machine ECM (MID 299)
DTC Code Description System Response
781-3 Lighting Relay : Voltage Above Normal Related lighting system will be ON continuously.
781-6 Lighting Relay : Current Above Normal Related lighting system will be ON continuously.
2912-3 Front Wiper Speed Control Relay : Voltage Above Normal Wiper system will not function.
2912-6 Front Wiper Speed Control Relay : Current Above Normal Wiper system will not function.
3634-3 Boom Light Relay : Voltage Above Normal Related lighting system will be ON continuously.
3634-6 Boom Light Relay : Current Above Normal Related lighting system will be ON continuously. Possible Causes for an FMI 3 Diagnostic code are:
The ground wire is open.
The signal wire is permanently open.
The signal wire is permanently closed.
The indicator lamp has failed.
The Switch Panel has failed. This situation is unlikely.Possible Causes for an FMI 6 Diagnostic code are:
A short to ground exists.
The indicator lamp has failed.
The Switch Panel has failed. This situation is unlikely.
Illustration 1 g03448477
Schematic of the relay circuit for the wiper control module
Illustration 2 g02722559
Schematic of the relay circuits associated with the Switch PanelNote: The diagram above is a simplified schematics of the Machine ECM and the Switch Panel connections. The schematic is electrically correct. However, not all of the possible harness connectors are shown. Refer to the latest revision of Electrical Schematic, KENR9677 (316E), Electrical Schematic, KENR9657 (312E), or Electrical Schematic, UENR3189 (318E) for the complete schematic.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that the diagnostic code is active before performing a troubleshooting procedure.
Table 2
Troubleshooting Test Steps Values Results
1. Identify Active FMI Code Associated With Relay Circuit
Code present. FMI 3 diagnostic code, proceed to Test Step 2.
FMI 6 diagnostic code, proceed to Test Step 3.
Begin Process For FMI 3 Troubleshooting HERE
2. Check The Machine Harness For A Short
A. Turn key start switch and disconnect switch OFF.
B. Disconnect harness connection at relay.
C. If relay connected to ECM, disconnect J1 and J2 connectors from ECM. If relay connected to Switch Panel, disconnect all switch panel connectors.
D. Measure resistance of relay signal contact to all J1 and J2 connectors, if relay is wired directly to Machine ECM. If relay is wired directly to switch panel, measure resistance of relay contact to all switch panel connectors.
Each reading greater than 5K Ω. OK - All resistance measurements are greater than 5K Ω.
Proceed to Test Step 5.
NOT OK - One or
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
24H, AP-800C, AP-800D, BG-225B, CB-224C, CB-334D, CB-335D, CB-434B, CB-434C, CB-534B, CB-534C, CB-544, CB-545, CB-634C, CP-433C, CP-563, CS-431C, CS-433C, CS-531C, CS-531D, CS-533C, CS-533D, CS-563C, ...
10 FT, 10-20B, 8 FT, 8-16B, AP-1000, AP-1000B, AP-1055D, AP-655C, AP-900B, AS3251C, AS3301C, BG-2455D, BG-260D, PM-201, PM-565, PM-565B, PP120, RM-350B, RM-500
AP-200, AP-200B, CP-433B, CP-433C, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-563, CP-573E, CP-64, CP-68B, CS-323C, CS-423E, CS-431B, CS-431C, CS-433C, CS-433E, CS-44, CS-531, CS-531C, CS-531D, CS-533...
CB-534B, CB-534C, CB-535B, CB-634, CB-634C, CP-433C, CS-323C, CS-433C, PM-201, PM-465, PM-565, PM-565B
CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CB-634, CB-634C, CP-433C, CP-563, CS-431C, CS-433C, CS-531, CS-531C, CS-531D, CS-533C, CS-533D, CS-563C, CS-563D, CS-573D, CS-583, CS-583C,...
CP-563, CS-531C, CS-531D, CS-533C, CS-533D, CS-563C, CS-563D, CS-573D, CS-583, CS-583C, CS-583D, PR-105
CB-534B, CB-534C, CB-535B, CB-564D, CB-634C, CB-634D, CB-64, CP-433C, CS-431C
CP-433C, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-573E, CP-64, CP-663E, CP-68B, CP-74B, CP-76, CS-423E, CS-431C, CS-433E, CS-44, CS-531C, CS-531D, CS-533C, CS-533D, CS-533E, CS-54, CS-54B, CS-56, CS...
AP-1055D, AP-600D, AP-655D, AP555E, BG500E, BG600D, BG655D, CP-433C, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-573E, CP-64, CP-663E, CP-68B, CP-74B, CP-76, CS-423E, CS-433E, CS-44, CS-533C, CS-533D, ...
AP-1055D, AP-600D, AP-655D, AP555E, BG500E, BG600D, BG655D, CP-533E, CP-54B, CP-56, CP-573E, CP-64, CP-663E, CP-68B, CP-74B, CP-76, CS-533C, CS-533D, CS-533E, CS-54, CS-54B, CS-56, CS-563C, CS-563D, C...
CS-533C, CS-563C, CS-573C, CS-583C
0983394
SEAL-O-RING
AP-200, AP-200B, CS-563E
AP-200, AP-200B, CS-563E
2136005
SEAL-LIP TYPE
AP-200B
AP-200B
1G7394
SEAL-O-RING
AP-200B, CP-433B, CS-431C, CS-531
AP-200B, CP-433B, CS-431C, CS-531
1G7391
SEAL-O-RING
AP-200B
AP-200B
1G7373
SEAL-O-RING
AP-200B
AP-200B
1G7369
SEAL-LIP TYPE
AP-200B, CS-323C
AP-200B, CS-323C
0776630
SEAL
CP-433B, CP-433C, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-563, CP-573E, CP-64, CP-68B, CP-74B, CS-323C, CS-423E, CS-431B, CS-431C, CS-433C, CS-433E, CS-44, CS-531, CS-531C, CS-531D, CS-533, CS-533C...
CP-433B, CP-433C, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-563, CP-573E, CP-64, CP-68B, CP-74B, CS-323C, CS-423E, CS-431B, CS-431C, CS-433C, CS-433E, CS-44, CS-531, CS-531C, CS-531D, CS-533, CS-533C...
CB-534B, CB-534C, CB-534D, CB-535B, CB-54, CB-564D, CB-634C, CB-634D, CB-64, CP-433C, CP-433E, CP-44, CS-323C, CS-423E, CS-431C, CS-433C, CS-433E, CS-44, CS-531C, CS-533C, CS-563C, PM-565, PR-450, PR-...
1029996
SEAL-CASE
AP-200B
AP-200B
1G8792
SEAL-OIL
AP-200B
AP-200B
1G8776
SEAL-CASE
AP-200B
AP-200B
AP-200, AP-200B, CP-433B, CP-433C, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-563, CP-573E, CP-64, CP-68B, CS-323C, CS-423E, CS-431B, CS-431C, CS-433C, CS-433E, CS-44, CS-531, CS-531C, CS-531D, CS-533...