0951607 SEAL-O-RING Caterpillar parts
301.5, 301.6C, 307, 307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311, 311B, 312, 312B, 312B L, 312C L, 313B, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH,...
Rating:
Alternative (cross code) number:
CA0951607
095-1607
0951607
CA0951607
095-1607
0951607
Weight: 0.01 pounds 0 kg.
Information:
CROSS SECTION DIAMETER
3.5
mm
ID
43.7
mm
MATERIAL
Nitrile (NBR) Rubber 90 Duro
OD
0
mm
COLD PLANER, MOBILE HYD POWER UNIT,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
O ring for Caterpillar PM-465 301.5 301.6 307 308 311 0951607 095-1607
EXSOLID High quality replacement part || O ring for Caterpillar || Fits for: PM-465, 301.5, 301.6, 307, 308, 311, 312, 313, 365, 374, 385, 390, E70, E110, E120, E650 || Part numbers: 095-1607, 0951607 || If you are not sure this item can fit your vehicle, please contact us before ordering
EXSOLID High quality replacement part || O ring for Caterpillar || Fits for: PM-465, 301.5, 301.6, 307, 308, 311, 312, 313, 365, 374, 385, 390, E70, E110, E120, E650 || Part numbers: 095-1607, 0951607 || If you are not sure this item can fit your vehicle, please contact us before ordering
O Ring for Caterpillar PM-465 301.5 301.6 307 308 311 0951607 095-1607
EXSOLID High quality replacement part || O ring for Caterpillar || Fits for: PM-465, 301.5, 301.6, 307, 308, 311, 312, 313, 365, 374, 385, 390, E70, E110, E120, E650 || Part numbers: 095-1607, 0951607 || If you are not sure this item can fit your vehicle, please contact us before ordering
EXSOLID High quality replacement part || O ring for Caterpillar || Fits for: PM-465, 301.5, 301.6, 307, 308, 311, 312, 313, 365, 374, 385, 390, E70, E110, E120, E650 || Part numbers: 095-1607, 0951607 || If you are not sure this item can fit your vehicle, please contact us before ordering
$3.25
29 Sep 2018
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
CATERPILLAR SEAL O RING 0951607 NEW
Number on catalog scheme:
10
For full view, you need register
Compatible equipment models: 0951607:
Information:
Removal Procedure
Personal injury can result from hot coolant, steam and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove cooling system pressure cap slowly to relieve pressure only when engine is stopped and cooling system pressure cap is cool enough to touch with your bare hand.Do not attempt to tighten hose connections when the coolant is hot, the hose can come off causing burns.Cooling System Coolant Additive contains alkali. Avoid contact with skin and eyes.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or disposal.
Illustration 1 g00952382
Remove bolts (2) and clamp (3) from housing assembly (1) .
Illustration 2 g00952383
Remove housing assembly (1) and gasket (4) from the engine. Remove water temperature regulators (6) and (7) and lip seal (5) from housing (8) .Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00952383
Clean all mating surfaces. Install water temperature regulators (6) and (7) and lip seal (5) in housing (8). Install gasket (6) on housing assembly (1) .
Illustration 4 g00952382
Position housing assembly (1) and the gasket on the housing. Install bolts (2) and clamp (3) to housing assembly (1) .
Fill the cooling system with coolant to the correct level. Refer to the Operation and Maintenance Manual for the correct filling procedure.
Personal injury can result from hot coolant, steam and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove cooling system pressure cap slowly to relieve pressure only when engine is stopped and cooling system pressure cap is cool enough to touch with your bare hand.Do not attempt to tighten hose connections when the coolant is hot, the hose can come off causing burns.Cooling System Coolant Additive contains alkali. Avoid contact with skin and eyes.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or disposal.
Illustration 1 g00952382
Remove bolts (2) and clamp (3) from housing assembly (1) .
Illustration 2 g00952383
Remove housing assembly (1) and gasket (4) from the engine. Remove water temperature regulators (6) and (7) and lip seal (5) from housing (8) .Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00952383
Clean all mating surfaces. Install water temperature regulators (6) and (7) and lip seal (5) in housing (8). Install gasket (6) on housing assembly (1) .
Illustration 4 g00952382
Position housing assembly (1) and the gasket on the housing. Install bolts (2) and clamp (3) to housing assembly (1) .
Fill the cooling system with coolant to the correct level. Refer to the Operation and Maintenance Manual for the correct filling procedure.
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
345C, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 385C L
330C, 330D L, 330D MH, 345B II, 345B II MH, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 374D L, 374F L
345B II, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L
365B, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
365B, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
385B, 385C, 385C L, 390D, 390D L
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
330, 330 FM L, 330 L, 330B, 330B L, E120B, W330B
365C, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
307, 307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 3...
7Y8555
SEAL
311, 312, 315, 950H, 962H, 966H, 972H, 973C, AS4173
311, 312, 315, 950H, 962H, 966H, 972H, 973C, AS4173
5P5934
SEAL
307, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320C, 322 FM L, 325 L, 325 LN, 330, 330 FM L, 330 L, 375, 375 L, 5080, 518, 518C, 621B, 621E, 623B, 623E, 627B, 627E, 631E, 633E II, 637D, 637...
307, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320C, 322 FM L, 325 L, 325 LN, 330, 330 FM L, 330 L, 375, 375 L, 5080, 518, 518C, 621B, 621E, 623B, 623E, 627B, 627E, 631E, 633E II, 637D, 637...
1141558
SEAL
311, 311B, 312, 312B, 312B L, 313B, 315, 317
311, 311B, 312, 312B, 312B L, 313B, 315, 317
2030837
SEAL GP-DUO-CONE
312, 312B L, 312C, 315B L, 317B LN, 318B
312, 312B L, 312C, 315B L, 317B LN, 318B
1281848
SEAL-FACE
312, 375 L
312, 375 L
0874577
SEAL
303, 303.5, 303.5C, 303.5E, 303C CR, 304, 304.5, 304C CR, 304E, 305, 305.5, 305.5E, 305C CR, 305E, 306, 306E, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311B, 311C, 311D LRR,...
303, 303.5, 303.5C, 303.5E, 303C CR, 304, 304.5, 304C CR, 304E, 305, 305.5, 305.5E, 305C CR, 305E, 306, 306E, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311B, 311C, 311D LRR,...
304, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D C...
311, 311B, 311C, 312, 312B, 312B L, 312C, 312C L, 313B, 314C, E110B, E120B
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 323D LN, E110...
307D, 308D, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, E110B, ...
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, E110B, E120B