0951709 SEAL-O-RING Caterpillar parts
2384C, 2484C, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304.5, 304C CR, 304D CR, 304E, 305, 305D CR, 305E, 308E, 308E CR, 308E SR, 311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 31...
Rating:
Alternative (cross code) number:
CA0951709
095-1709
0951709
CA0951709
095-1709
0951709
Weight: 0.01 pounds 0 kg.
Information:
CROSS SECTION DIAMETER
3.1
mm
ID
74.4
mm
MATERIAL
Nitrile (NBR) Rubber 90 Duro
OD
0
mm
COMPACT WHEEL LOADER, VIBRATORY COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$4.40
17 Oct 2018
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
CATERPILLAR SEAL O RING 0951709 NEW
$4.54
27 May 2022
0.1102[0.05] Pounds
US: TakePart
CTP Caterpillar Nbr (90) O-Ring (0951709) Aftermarket
CTP
CTP
This part in 2 request:
Show.
This information for suppliers only!
2019-02-07
2019-02-07
Number on catalog scheme:
16
For full view, you need register
Compatible equipment models: 0951709:
EXCAVATOR
311
311B
312
312B
312B L
315
315B
315B FM L
315B L
317
317B LN
318B
330
330 FM L
330 L
350
E110B
E120B
E180
E240
E300
E300B
E450
E650
E70B
HAMMER
H110E S
MINI HYD EXCAVATOR
303.5
303.5C
303.5D
303.5E
303C CR
303E CR
304.5
304C CR
304D CR
304E
305
305D CR
305E
308E
308E CR
308E SR
UNDERCARRIAGE
OEMS
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
B 8T-5096 Dial Indicator Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Place clean engine oil on the crankshaft main bearings prior to assembly. Ensure that the tabs on the back side of the crankshaft main bearings fit in the grooves of the crankshaft main bearing caps and the cylinder block.
Illustration 1 g01153704
Use Tooling (A) and install the upper halves of the crankshaft main bearings in the cylinder block. Do not put oil on the back of the crankshaft main bearing.
Install the lower halves of the crankshaft main bearings in crankshaft main bearing caps (2). Do not put oil on the back of the crankshaft main bearing.
Crankshaft main bearing caps should be installed with the part number toward the front of the engine. Crankshaft main bearing caps are to be identified by stamped numbers 1 through 7 that are located on the bottom surface of the bearing cap. The thrust plate is used on the number 6 main bearing.
Place crankshaft main bearing caps (2) in position on the cylinder block. Place clean engine oil or Molylube on the bolt threads and the washer face. Install bolts (1).
Tighten each bolt (1) to a torque of 95 5 N m (70 4 lb ft). Tighten each bolt (1) for an additional 90 5 degrees (1/4 turn).
Check the end play of the crankshaft with Tooling (B). The end play must be 0.21 - 0.60 mm (0.008 - 0.024 inch). End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
B 8T-5096 Dial Indicator Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Place clean engine oil on the crankshaft main bearings prior to assembly. Ensure that the tabs on the back side of the crankshaft main bearings fit in the grooves of the crankshaft main bearing caps and the cylinder block.
Illustration 1 g01153704
Use Tooling (A) and install the upper halves of the crankshaft main bearings in the cylinder block. Do not put oil on the back of the crankshaft main bearing.
Install the lower halves of the crankshaft main bearings in crankshaft main bearing caps (2). Do not put oil on the back of the crankshaft main bearing.
Crankshaft main bearing caps should be installed with the part number toward the front of the engine. Crankshaft main bearing caps are to be identified by stamped numbers 1 through 7 that are located on the bottom surface of the bearing cap. The thrust plate is used on the number 6 main bearing.
Place crankshaft main bearing caps (2) in position on the cylinder block. Place clean engine oil or Molylube on the bolt threads and the washer face. Install bolts (1).
Tighten each bolt (1) to a torque of 95 5 N m (70 4 lb ft). Tighten each bolt (1) for an additional 90 5 degrees (1/4 turn).
Check the end play of the crankshaft with Tooling (B). The end play must be 0.21 - 0.60 mm (0.008 - 0.024 inch). End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
330, 330B, 330B L, OEMS
330, 330 L, 345B, 345B II, 345B L, 350, OEMS
350, 350 L, S25
350, 350 L, S25
325B L, 330, 330 FM L, 330 L, 330B L, 350, 350 L, CR20, P16
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
345B II, 345B L, 350, 365B, 365B II, 365B L
330, 330 FM L, 330 L, 330B, 330B L, E120B, W330B
330 L
345B II, 345C, E120, E140, E180, E240, E240C, E300, E300B, E450, EL240B
E180, E200B, E240, EL240B
311, 312, 320 L, 320N, 322, 322 FM L, 322 LN, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, 350, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5080, 5090B, E300, E450, E650, TK1051
305, 308E, 308E CR, 308E SR, 308E2 CR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 3...
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 31...
308E, 308E CR, 308E SR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LC...
1906304
SEAL AS
307, 312, 312B L, 315, 315B L, 317, 317B LN, 318B
307, 312, 312B L, 315, 315B L, 317, 317B LN, 318B
120H ES, 12H ES, 140H ES, 160H ES, 307B, 307C, 308C, 311, 311B, 312, 312B L, 315, 315B, 315B L, 317, 317B LN, 318B, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B L, 320C, 320N, 322 FM L, 322 LN...
6C8970
SEAL
311B, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322B LN, 325 L, 325B L, 330B L, 345B II, 345B L, 350, 350 L, 365B, 365B II, 375, 385B, 5080, 5090B
311B, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322B LN, 325 L, 325B L, 330B L, 345B II, 345B L, 350, 350 L, 365B, 365B II, 375, 385B, 5080, 5090B
311, 311B, 311C, 312, 312B, 312B L, 312C, 312C L, 313B, 314C, 320 L, 320B, 320C, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 320N, 322 L, 322B, 322B L, 322C, 322C FM, 323D L, 324D, 324D L, 32...
307C, 307D, 307E, 308E, 311, 311B, 311C, 312, 312B, 312B L, 312C, 312C L, 312D, 313B, 314C, 320B, 320C, 320N, 322B, 322B L, 322C, 322C FM, 323D L, 325, 325 L, 325B L, 325C, 325C L, 325D, 329D L, 329D ...
302.5, 303.5C, 303.5D, 303C CR, 304, 304.5, 304C CR, 304D CR, 305, 305.5, 305.5D, 305C CR, 305D CR, 306, 307, 307B, 307D, 308D, 308E2 CR, 311, 312, 315, 317, 320 L, 324D, 324D L, 324E, 325, 325 L, 325...
303.5, 308E2 CR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E...
303.5C, 308E, 308E CR, 308E SR, 311, 311B, 311D LRR, 312, 312B, 312B L, 312D, 312D L, 312E L, 314D CR, 314D LCR, 314E LCR, 315, 315B, 315B FM L, 315B L, 315D L, 317, 317B LN, 318B, 5130, 5130B, 5230, ...