0951718 SEAL-O-RING Caterpillar parts
301.5, 303, 303.5, 308E, 308E CR, 308E SR, 308E2 CR, 311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 315C, 317, 317B LN, 318B, 320B L, 320C, 320E L, 321B, 321C, 321D LCR, E110, E120, E140,...
Rating:
Alternative (cross code) number:
CA0951718
095-1718
0951718
CA0951718
095-1718
0951718
Weight: 0.01 pounds 0 kg.
Information:
CROSS SECTION DIAMETER
3.1
mm
ID
119.4
mm
MATERIAL
Nitrile (NBR) Rubber 90 Duro
OD
0
mm
EXCAVATOR, MINI HYD EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$4.39
08 Oct 2018
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
CATERPILLAR SEAL O RING 0951718 NEW
$4.65
06 Jun 2022
0.1102[0.05] Pounds
US: TakePart
CTP Caterpillar Nbr (90) O-Ring (0951718) Aftermarket
CTP
CTP
Number on catalog scheme:
11
For full view, you need register
Compatible equipment models: 0951718:
Information:
Installation of the Wear Sleeve
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-0914 Guide Pin 2
B 121-7705 Stud Assembly 4
C 200-5958 Wear Sleeve Installer 1
D 5P-8245 Hard Washer 4
E 1F-7958 Full Nut 4
F 4C-9507 Retaining Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The crankshaft adapter must be installed on the crankshaft in order to install the wear sleeve. If the crankshaft adapter was removed, Steps 1 through 4 describe installation of the crankshaft adapter. If the crankshaft adapter was not removed, go to Step 6.
Illustration 1 g00633265
Typical example
Install Tooling (A) into the rear of the crankshaft.
Make sure that the arrow on the crankshaft adapter will point in the direction of the crankshaft rotation when the crankshaft adapter is installed. Attach a suitable lifting device to crankshaft adapter (1). Lift the crankshaft adapter onto Tooling (A). The crankshaft adapter weighs approximately 77 kg (170 lb).
Illustration 2 g00633171
Slide crankshaft adapter (1) toward the crankshaft. Install bolts (2) that attach the crankshaft adapter to the crankshaft.
Remove Tooling (A) from the crankshaft.
Illustration 3 g00633181
(B) Stud assembly (C) Wear sleeve installer (D) Hard washer (E) Full nut
Install Tooling (B) into two of the holes in the rear housing. Bolts (3) for the adapter of the crankshaft seal will be installed in these holes later.
Place a new wear sleeve into Tooling (C). Make sure that the arrow on the outside of the wear sleeve will point in the direction of the crankshaft rotation when the wear sleeve is installed.
Apply Tooling (F) to the inside diameter of the wear sleeve.
Place Tooling (C) and the wear sleeve onto Tooling (B). Install Tooling (D) and Tooling (E) onto Tooling (B) .
Tighten the nuts for Tooling (E) evenly in order to press the wear sleeve onto the crankshaft adapter. Press the wear sleeve onto the crankshaft adapter until the wear sleeve contacts the shoulder of the adapter.
Remove Tooling (E), Tooling (D), Tooling (C), and Tooling (B) .Installation of the Rear Seal
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-6241 Seal Installer
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The Tooling (A) is packaged with the new
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-0914 Guide Pin 2
B 121-7705 Stud Assembly 4
C 200-5958 Wear Sleeve Installer 1
D 5P-8245 Hard Washer 4
E 1F-7958 Full Nut 4
F 4C-9507 Retaining Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The crankshaft adapter must be installed on the crankshaft in order to install the wear sleeve. If the crankshaft adapter was removed, Steps 1 through 4 describe installation of the crankshaft adapter. If the crankshaft adapter was not removed, go to Step 6.
Illustration 1 g00633265
Typical example
Install Tooling (A) into the rear of the crankshaft.
Make sure that the arrow on the crankshaft adapter will point in the direction of the crankshaft rotation when the crankshaft adapter is installed. Attach a suitable lifting device to crankshaft adapter (1). Lift the crankshaft adapter onto Tooling (A). The crankshaft adapter weighs approximately 77 kg (170 lb).
Illustration 2 g00633171
Slide crankshaft adapter (1) toward the crankshaft. Install bolts (2) that attach the crankshaft adapter to the crankshaft.
Remove Tooling (A) from the crankshaft.
Illustration 3 g00633181
(B) Stud assembly (C) Wear sleeve installer (D) Hard washer (E) Full nut
Install Tooling (B) into two of the holes in the rear housing. Bolts (3) for the adapter of the crankshaft seal will be installed in these holes later.
Place a new wear sleeve into Tooling (C). Make sure that the arrow on the outside of the wear sleeve will point in the direction of the crankshaft rotation when the wear sleeve is installed.
Apply Tooling (F) to the inside diameter of the wear sleeve.
Place Tooling (C) and the wear sleeve onto Tooling (B). Install Tooling (D) and Tooling (E) onto Tooling (B) .
Tighten the nuts for Tooling (E) evenly in order to press the wear sleeve onto the crankshaft adapter. Press the wear sleeve onto the crankshaft adapter until the wear sleeve contacts the shoulder of the adapter.
Remove Tooling (E), Tooling (D), Tooling (C), and Tooling (B) .Installation of the Rear Seal
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-6241 Seal Installer
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The Tooling (A) is packaged with the new
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LRR, 320D RR, 323D L, 323D LN
320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 L, 321C, 321D LCR, 322C, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D L, 325C, 325D, 325D L...
320C, 320D, 320D L, 320D LN, 320D LRR, 320D2, 320D2 L, 322C, 323D L, 323D2 L, 324D, 324D L, 325C, 325D L, 329D, 329D L
320C, 320D, 321B, 321C, 321D LCR, 322C, 324D, 324D L, 325C, 325C L, 328D LCR, 330C L
320C, 320D, 320D L, 320D LN, 320D LRR, 320D2 L, 322C, 323D L
320C, 320D, 320D L, 320E L, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L, 330C L
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 3...
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 3...
320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 325D, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
320 L, 320N, 322, 322 FM L, 322 LN, E110, E180, E200B, E240, E240C, E300B, EL240B, OEMS
345B II, 345C, E120, E140, E180, E240, E240C, E300, E300B, E450, EL240B
0996532
SEAL-O-RING
311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 3...
311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 3...
303E CR, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2,...
2384C, 2484C, 301.5, 302.7D, 303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 307B, 307C, 308C, 311, 311B, 31...
2384C, 2484C, 302.5, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 307, 307B, 307C, 307D, 307E, 308...
311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 3...
120M, 12M, 140M, 14M, 160M, 16M, 2384C, 2484C, 24M, 303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 307B, 307C, 307D, 308C, 308D, 308E, 3...
303, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312E, 312E L, 313D, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 315B FM L, 315B L, 315C, 315D...
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN
303.5, 303.5C, 303.5D, 303.5E, 303C CR, 304C CR, 304D CR, 304E, 305D CR, 305E, 307, 307B, 308E, 308E CR, 308E SR, 308E2 CR, 311, 311B, 311C, 312, 312B, 312B L, 312C, 314C, 315, 315B, 315B FM L, 315B L...
301.5, 303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304.5, 304C CR, 304D CR, 304E, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 308E, 308E CR, 308E SR, 311, 311B, 311D LRR, 311F LRR, 312, 312...
1090, 1190, 1190T, 1290T, 1390, 2290, 2384C, 2390, 2391, 2484C, 2491, 2590, 308E, 308E CR, 308E SR, 308E2 CR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2,...
1090, 1190, 1190T, 1290T, 1390, 2290, 2384C, 2390, 2391, 2484C, 2491, 2590, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306,...