0951733 SEAL-O-RING Caterpillar parts
115, 312D2, 350, 350 L, 365B, 365B II, 365C, 365C L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5090B, 5110B, 901C, 902C, 903C, CR20, E70, H140CS, P16, S25
Rating:
Alternative (cross code) number:
CA0951733
095-1733
0951733
CA0951733
095-1733
0951733
Weight: 0.02 pounds 0 kg.
Information:
CROSS SECTION DIAMETER
5.7
mm
ID
209.3
mm
MATERIAL
Nitrile (NBR) Rubber 90 Duro
OD
0
mm
COMPACT WHEEL LOADER, SHEAR-DEMOLITION/SCRAP,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$10.05
29 May 2022
0.1102[0.05] Pounds
US: ProperBuy
CTP Caterpillar Nbr (90) O-Ring (0951733) Aftermarket
CTP
CTP
Compatible equipment models: 0951733:
Information:
Assembly Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     6V-6192     Pliers     1    
B     7M-3978     Piston Ring Expander Gp     1    
C     5P-8639     Hydraulic Press (Connecting Rod Bearing)     1    
8F-0024 Hose Assembly     1    
1P-2375 Connecting Coupler     1    
1P-2376 Connecting Coupler     1    
5P-8651 Spacer     1    
5P-8649 Adapter     1    
8P-8650 Bushing Adapter     1    
9U-6600 Hydraulic Pump     1    Note: Prior to removal from the engine, the pistons and connecting rod assemblies were marked. The components must be reassembled together. The components must be installed in the original location in the engine. Do not interchange any of the components.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01104123
Use Tooling (C) to remove the old bearing and install the new bearing (4) at the same time. The adapter of Tooling (C) should make full contact with the surfaces of connecting rod (8) .Note: Orient the bearing joint within 5 degrees of either Location (X) .
The connecting rod must be heated for the installation of the piston pin bearing. Do not use a torch.
Heat Length (Y) of connecting rod (6) to a temperature of 175 to 260 °C (347 to 500 °F). (Y) Maximum Length for heating the connecting rod ... 85 mm (3.3 inch)
Allow the connecting rod and the bearing to cool to room temperature.
Use a pin boring machine to machine the bore of bearing (4) to the correct diameter.Diameter of bearing bore ... 55.035 0.008 mm (2.1667 0.0003 inch)
Illustration 2 g01103998
Position the spring for the oil control ring in the oil ring groove in the piston crown.
Position oil control ring (3) over the spring. Position the oil control ring so that the gap is 180 degrees from the joint in the spring. Use Tooling (B) to install the oil control ring on piston crown (6) .
Use Tooling (B) to install intermediate piston ring (2) with the side that has the identification "UP-2" toward the top of the piston.
Use Tooling (B) to install top piston ring (1) with the side that has the identification "UP-1" toward the top of the piston.
Position piston rings (1), (2), and (3) so the gaps are 120 degrees from each other.
Check the clearance between the ends of piston rings (1), (2), and (3). Refer to the Specifications Manual, "Pistons And Rings" for the specifications.
Put piston crown (6) and piston skirt (7) in position on connecting rod (8). Apply clean engine oil to connecting rod pin (10) and install the connecting rod pin. Install pin retainer (5) with Tooling (A). Make sure that the pin retainers are fully seated in the grooves of the piston skirt.
Install connecting rod bearings (9) in connecting rod (8) and connecting rod cap (11). Make sure that the bearings are installed so that the bearing tabs
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     6V-6192     Pliers     1    
B     7M-3978     Piston Ring Expander Gp     1    
C     5P-8639     Hydraulic Press (Connecting Rod Bearing)     1    
8F-0024 Hose Assembly     1    
1P-2375 Connecting Coupler     1    
1P-2376 Connecting Coupler     1    
5P-8651 Spacer     1    
5P-8649 Adapter     1    
8P-8650 Bushing Adapter     1    
9U-6600 Hydraulic Pump     1    Note: Prior to removal from the engine, the pistons and connecting rod assemblies were marked. The components must be reassembled together. The components must be installed in the original location in the engine. Do not interchange any of the components.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01104123
Use Tooling (C) to remove the old bearing and install the new bearing (4) at the same time. The adapter of Tooling (C) should make full contact with the surfaces of connecting rod (8) .Note: Orient the bearing joint within 5 degrees of either Location (X) .
The connecting rod must be heated for the installation of the piston pin bearing. Do not use a torch.
Heat Length (Y) of connecting rod (6) to a temperature of 175 to 260 °C (347 to 500 °F). (Y) Maximum Length for heating the connecting rod ... 85 mm (3.3 inch)
Allow the connecting rod and the bearing to cool to room temperature.
Use a pin boring machine to machine the bore of bearing (4) to the correct diameter.Diameter of bearing bore ... 55.035 0.008 mm (2.1667 0.0003 inch)
Illustration 2 g01103998
Position the spring for the oil control ring in the oil ring groove in the piston crown.
Position oil control ring (3) over the spring. Position the oil control ring so that the gap is 180 degrees from the joint in the spring. Use Tooling (B) to install the oil control ring on piston crown (6) .
Use Tooling (B) to install intermediate piston ring (2) with the side that has the identification "UP-2" toward the top of the piston.
Use Tooling (B) to install top piston ring (1) with the side that has the identification "UP-1" toward the top of the piston.
Position piston rings (1), (2), and (3) so the gaps are 120 degrees from each other.
Check the clearance between the ends of piston rings (1), (2), and (3). Refer to the Specifications Manual, "Pistons And Rings" for the specifications.
Put piston crown (6) and piston skirt (7) in position on connecting rod (8). Apply clean engine oil to connecting rod pin (10) and install the connecting rod pin. Install pin retainer (5) with Tooling (A). Make sure that the pin retainers are fully seated in the grooves of the piston skirt.
Install connecting rod bearings (9) in connecting rod (8) and connecting rod cap (11). Make sure that the bearings are installed so that the bearing tabs
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
1672494
SEAL-WIPER
385B, CR20
385B, CR20
1119957
SEAL-LIP TYPE
325B L, 330, 330 FM L, 330 L, 330B L, 350, 350 L, CR20, P16
325B L, 330, 330 FM L, 330 L, 330B L, 350, 350 L, CR20, P16
2147880
SEAL GP-DUO-CONE
345B II, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L
345B II, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L
3673929
SEAL-U-CUP
365B, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
365B, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
3673928
SEAL-BUFFER
365B, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
365B, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
1362942
SEAL-O-RING
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L
3678471
SEAL-O-RING
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
2160010
SEAL-U-CUP
385B, 385C, 385C L, 390D, 390D L
385B, 385C, 385C L, 390D, 390D L
0931347
SEAL-O-RING
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
1132073
SEAL-O-RING
345B II, 345B L, 350, 365B, 365B II, 365B L
345B II, 345B L, 350, 365B, 365B II, 365B L
1659292
SEAL-LIP TYPE
365B, 365B L
365B, 365B L
3678472
SEAL-O-RING
365C, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
365C, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
8C9182
SEAL AS
312D2, 350, 350 L, 365B, 365B II, 365C, 365C L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5090B, 5130B, CR20, P16, S25
312D2, 350, 350 L, 365B, 365B II, 365C, 365C L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5090B, 5130B, CR20, P16, S25
3673933
SEAL-U-CUP
312D2, 374D L, 374F L, 385C L, 390D, 390D L, 390F L
312D2, 374D L, 374F L, 385C L, 390D, 390D L, 390F L
0951732
SEAL-O-RING
312D2, 385B, 385C, 385C L, 390D, 390D L, 988K
312D2, 385B, 385C, 385C L, 390D, 390D L, 988K
1723918
SEAL AS
312D2, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 988K
312D2, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 988K
3673932
SEAL-BUFFER
312D2, 374D L, 374F L, 385C L, 390D, 390D L, 390F L
312D2, 374D L, 374F L, 385C L, 390D, 390D L, 390F L
1659295
SEAL-LIP TYPE
312D2, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
312D2, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
4180957
SEAL-VALVE STEM
306E, 307E
306E, 307E
4180993
SEAL
306E, 307E
306E, 307E
3857944
SEAL-AIR
318D2 L
318D2 L
1709853
SEAL-BUFFER
312D2, 365B II, 365C, 365C L, 375, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B, 5110B
312D2, 365B II, 365C, 365C L, 375, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B, 5110B
2160011
SEAL-U-CUP
312D2, 365B II, 365C, 365C L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
312D2, 365B II, 365C, 365C L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
1659296
SEAL-LIP TYPE
312D2, 365B, 365B II, 365C, 365C L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5090B
312D2, 365B, 365B II, 365C, 365C L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5090B