0960059 SEAL-LIP TYPE Caterpillar parts
322B LN, 325 LN, E240, E240C, E300, E450, EL240B
Rating:
Alternative (cross code) number:
CA0960059
096-0059
0960059
CA0960059
096-0059
0960059
Weight: 0.010 pounds 0 kg.
Information:
COUNTERBORE AXIAL DEPTH
8.35
mm
GROOVE DIAMETER
114.23
mm
MATERIAL
Urethane Rubber - 90 Duro
ROD DIAMETER
0
mm
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$16.97
17 May 2021
0.1984[0.09] Pounds
US: IronDT
CTP Caterpillar Press-in Wiper Seal (0960059) Aftermarket
CTP
CTP
Number on catalog scheme:
20
For full view, you need register
Compatible equipment models: 0960059:
Information:
Removal Procedure
Start By:
Remove the heat shields, if equipped.
Remove the cover for the fuel injectors. Refer to this Disassembly and Assembly Manual, "Fuel Injector Cover - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01230033
Typical example
Remove the breather tube (3) from the valve mechanism cover (1). Refer to Disassembly and Assembly Manual, "Crankcase Breather - Remove and Install".
Remove the fasteners (2). Remove the valve mechanism cover (1). Remove the joint for the valve mechanism cover and discard the joint. Installation Procedure
Illustration 2 g01230033
Typical example
Thoroughly clean the valve mechanism cover (1). Ensure that the groove for the joint for the valve mechanism cover (1) is clean and dry. Ensure that the mating face on the cylinder head is clean and dry.
If the valve mechanism cover (1) is equipped with an oil filler cap, check the condition of the O-ring for the oil filler cap. If necessary, replace the O-ring.
Install a new joint to the valve mechanism cover (1) and install the valve mechanism cover onto the cylinder head.
Check the condition of the fasteners (2). Replace the fasteners (2), if necessary. Install the fasteners (2).
Illustration 3 g01018519
Sequence for tightening the fasteners for the three cylinder engine
Tighten the fasteners for the valve mechanism cover in the sequence that is shown in Illustration 3. Tighten the fasteners to a torque of 9 N m (80 lb in).
Connect the breather tube (3) to the valve mechanism cover (1). Refer to Disassembly and Assembly Manual, "Crankcase Breather - Remove and Install". End By:
Install the cover for the fuel injectors. Refer to this Disassembly and Assembly Manual, "Fuel Injector Cover - Remove and Install".
If equipped, ensure that the heat shields are clean and free from dust, oil, and paint. Install the heat shields.
Start By:
Remove the heat shields, if equipped.
Remove the cover for the fuel injectors. Refer to this Disassembly and Assembly Manual, "Fuel Injector Cover - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01230033
Typical example
Remove the breather tube (3) from the valve mechanism cover (1). Refer to Disassembly and Assembly Manual, "Crankcase Breather - Remove and Install".
Remove the fasteners (2). Remove the valve mechanism cover (1). Remove the joint for the valve mechanism cover and discard the joint. Installation Procedure
Illustration 2 g01230033
Typical example
Thoroughly clean the valve mechanism cover (1). Ensure that the groove for the joint for the valve mechanism cover (1) is clean and dry. Ensure that the mating face on the cylinder head is clean and dry.
If the valve mechanism cover (1) is equipped with an oil filler cap, check the condition of the O-ring for the oil filler cap. If necessary, replace the O-ring.
Install a new joint to the valve mechanism cover (1) and install the valve mechanism cover onto the cylinder head.
Check the condition of the fasteners (2). Replace the fasteners (2), if necessary. Install the fasteners (2).
Illustration 3 g01018519
Sequence for tightening the fasteners for the three cylinder engine
Tighten the fasteners for the valve mechanism cover in the sequence that is shown in Illustration 3. Tighten the fasteners to a torque of 9 N m (80 lb in).
Connect the breather tube (3) to the valve mechanism cover (1). Refer to Disassembly and Assembly Manual, "Crankcase Breather - Remove and Install". End By:
Install the cover for the fuel injectors. Refer to this Disassembly and Assembly Manual, "Fuel Injector Cover - Remove and Install".
If equipped, ensure that the heat shields are clean and free from dust, oil, and paint. Install the heat shields.
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322 FM L, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B, 325B L, 325C, 325C FM, ...
320 L, 320N, 322 FM L, 322 LN, 325, 325 L, 325 LN, 330, 330 FM L, 350, 350 L, 5080
328D LCR, 329D L, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330D L, 336D L, 345B II, 345B II MH, 345B L, 345D L, 350, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 375, 375 L, 385B, 385C, 5080,...
320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 320N, 321C, ...
322B L, 325B L, 330 FM L, 330B L, 330C, 330D L, 330D MH, 345B, 345B II, 345B L, 345C, 345C L, 345D L, 350, E450
320N, 322B, 322B L, 322C, 322C FM, 325, 325 L, 325 LN, 325B L, 325C, 330, 330 FM L, 330 L
321C, 322B, 322B L, 322B LN, 322C, 323D L, 323D LN, 324D L, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325D FM, 325D L, 328D LCR, 329D L, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 330D L, 336D L, 345...
320 L, 322 FM L, 322B LN, 325 LN, E240, E240C, E300, E450, EL240B
320 L, 320B, 320N, 322B, 322B LN, 325, 325 L, 325 LN, 325B L, 325C FM, 325D FM, 325D FM LL, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330C L, 345B II, 345B L, M325B
320 L, 320N, 322, 322 FM L, 322 LN, E110, E180, E200B, E240, E240C, E300B, EL240B, OEMS
345B II, 345C, E120, E140, E180, E240, E240C, E300, E300B, E450, EL240B
E180, E200B, E240, EL240B
320 L, 322 FM L, 322B LN, 325 LN, E240, E240C, E300, E450, EL240B
1174657
SEAL
322B L, 325B L, 330B L, 525B, 525C, 535B, 535C, 539, 545, 545C
322B L, 325B L, 330B L, 525B, 525C, 535B, 535C, 539, 545, 545C
1504539
SEAL-WIPER
322B L, 322C FM, 325B L, 330B L, 525C, 525D, CTV20, GH52
322B L, 322C FM, 325B L, 330B L, 525C, 525D, CTV20, GH52
1504553
SEAL-O-RING
322B L, 322C FM, 325B L, 330B L, GH52
322B L, 322C FM, 325B L, 330B L, GH52
1504552
SEAL-O-RING
322B L, 322C FM, 325B L, 330B L, GH52
322B L, 322C FM, 325B L, 330B L, GH52
1504540
SEAL-O-RING
322B L, 322C FM, 325B L, 330B L, GH52
322B L, 322C FM, 325B L, 330B L, GH52
1843901
SEAL
320B, 320B U
320B, 320B U
1557102
SEAL
320B, 320B L, 320B U
320B, 320B L, 320B U
1241586
SEAL
320B, 320B L, 320B U, 321B
320B, 320B L, 320B U, 321B
1627750
SEAL
M320
M320
1265253
SEAL
M320
M320
320 L, 320B, 320N, 322B, 322B LN, 325, 325 L, 325 LN, 325B L, 325C FM, 325D FM, 325D FM LL, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330C L, 345B II, 345B L, M325B