0966028 SEAL-O-RING Caterpillar parts
307, 307B, E200B, E240C, E300B, EL240B
Rating:
Alternative (cross code) number:
CA0966028
096-6028
0966028
CA0966028
096-6028
0966028
Weight: 0.01 pounds 0 kg.
Information:
CROSS SECTION DIAMETER
3.5
mm
ID
22
mm
MATERIAL
Nitrile (NBR) Rubber - 75 Duro
OD
0
mm
EXCAVATOR, MINI HYD EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$5.23
25 Aug 2022
0.1102[0.05] Pounds
US: TakePart
CTP Caterpillar O Ring (0966028)
CTP
CTP
$6.79
26 Jan 2019
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
CATERPILLAR SEAL O RING 0966028 NEW
$9.04
27 Jun 2022
0.1102[0.05] Pounds
US: ProperBuy
CTP Caterpillar O Ring (0966028)
CTP
CTP
Number on catalog scheme:
19
For full view, you need register
Compatible equipment models: 0966028:
Information:
Bore Runout (Radial Eccentricity) of the Flywheel Housing
Illustration 1 g00285934
8T-5096 Dial Indicator
Fasten a dial indicator to the flywheel so the anvil of the dial indicator will contact the bore of the flywheel housing.
Illustration 2 g00285936
Illustration 3 g00285932
Checking Bore Runout Of The Flywheel Housing
While the dial indicator is in the position at Location "C" adjust the dial indicator to 0.0 mm (.00 inch). Push the crankshaft upward against the top of the bearing. Refer to the Illustration 2. Write the measurement for bearing clearance on Line "1" in Column "C".Note: Write the measurements for the dial indicator with the correct notations. This notation is necessary for making the calculations in the chart correctly.
Divide the measurement from Step 2 by two. Write this number on Line "1" in Columns "B" and "D".
Turn the flywheel in order to put the dial indicator at position (A). Adjust the dial indicator to 0.0 mm (.00 inch).
Turn the flywheel counterclockwise in order to put the dial indicator at position (B). Write the measurements in the chart.
Turn the flywheel counterclockwise in order to put the dial indicator at position (C). Write the measurement in the chart.
Turn the flywheel counterclockwise until the dial indicator is at position (D). Write the measurement in the chart.
Add the lines together in each column.
Subtract the smaller number from the larger number in Column "B" and Column "D". Place this number on Line "III". The result is the horizontal eccentricity (out of round). Line "III" in Column "C" is the vertical eccentricity.
Illustration 4 g00286046
Graph For Total Eccentricity (1) Total vertical eccentricity. (2) Total horizontal eccentricity. (3) Acceptable value. (4) Unacceptable value.
On the graph for total eccentricity, find the point of intersection of the lines for vertical eccentricity and horizontal eccentricity.
If the point of intersection is in the range that is marked "Acceptable", the bore is in alignment.
If the point of intersection is in the range that is marked "Not Acceptable", the flywheel housing must be changed.
Illustration 1 g00285934
8T-5096 Dial Indicator
Fasten a dial indicator to the flywheel so the anvil of the dial indicator will contact the bore of the flywheel housing.
Illustration 2 g00285936
Illustration 3 g00285932
Checking Bore Runout Of The Flywheel Housing
While the dial indicator is in the position at Location "C" adjust the dial indicator to 0.0 mm (.00 inch). Push the crankshaft upward against the top of the bearing. Refer to the Illustration 2. Write the measurement for bearing clearance on Line "1" in Column "C".Note: Write the measurements for the dial indicator with the correct notations. This notation is necessary for making the calculations in the chart correctly.
Divide the measurement from Step 2 by two. Write this number on Line "1" in Columns "B" and "D".
Turn the flywheel in order to put the dial indicator at position (A). Adjust the dial indicator to 0.0 mm (.00 inch).
Turn the flywheel counterclockwise in order to put the dial indicator at position (B). Write the measurements in the chart.
Turn the flywheel counterclockwise in order to put the dial indicator at position (C). Write the measurement in the chart.
Turn the flywheel counterclockwise until the dial indicator is at position (D). Write the measurement in the chart.
Add the lines together in each column.
Subtract the smaller number from the larger number in Column "B" and Column "D". Place this number on Line "III". The result is the horizontal eccentricity (out of round). Line "III" in Column "C" is the vertical eccentricity.
Illustration 4 g00286046
Graph For Total Eccentricity (1) Total vertical eccentricity. (2) Total horizontal eccentricity. (3) Acceptable value. (4) Unacceptable value.
On the graph for total eccentricity, find the point of intersection of the lines for vertical eccentricity and horizontal eccentricity.
If the point of intersection is in the range that is marked "Acceptable", the bore is in alignment.
If the point of intersection is in the range that is marked "Not Acceptable", the flywheel housing must be changed.
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
1390, 2590, 312, 320, 320 L, 320B, 320C, 320N, 322B, 322B L, 322B LN, 322C, 322C FM, 323D L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325C FM, 325C L, 325D...
311, 311B, 312B, 320 L, 320B, 320N, E110, E110B, E120B, E200B
307, 307B, 315, 325, 325 LN, 330, 330 FM L, 330 L
307B
E180, E200B, E240, E240C, EL240B, R1300, R1300G, R1300G II
325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2484C, 2491, 2590, 322, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 ...
320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 320N, 321C, ...
320 L, 322 FM L, 322B LN, 325 LN, E240, E240C, E300, E450, EL240B
322B LN, 325 LN, E240, E240C, E300, E450, EL240B
320 L, 320N, 322, 322 FM L, 322 LN, E110, E180, E200B, E240, E240C, E300B, EL240B, OEMS
345B II, 345C, E120, E140, E180, E240, E240C, E300, E300B, E450, EL240B
303, 307, 365B, 365B L, 365C, 385B, 385C, 385C FS, 385C L, 385C L MH, E110, E120, E140
303.5C, 303C CR, 304, 304D CR, 305, 307, 307B, 307C, 308C, 311, 311B, 311C, 311D LRR, 311F LRR, 312C, 312D, 312D L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318E...
0956616
SEAL-O-RING
307, 350, 350 L, 375, 375 L, E70, E70B
307, 350, 350 L, 375, 375 L, E70, E70B
2384C, 2484C, 301.5, 304, 304C CR, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 307, 307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 320B FM LL, 320C, 320C FM, 320D, 320D L, 32...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304D CR, 304E, 305, 305.5, 305.5E, 306, 306E, 307, 307B, 307C, 307D, 307E, 308C, 308D,...
1624694
SEAL-RING
307, 307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR
307, 307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR
1339323
SEAL
307
307
305.5E, 305E, 307, 307B, 307C, 307D, 308C, 308D, 312C L, 902, 906, 908, E120B, E70, E70B
307, 307B, 308C, 308E SR, 345B II, 345C, E200B, E240, E240C, E300, E300B, E450, EL240B
307, 311C, 313B, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 3...
307, 307B, 307C, 308C, 315, 315B, 315C, 317B LN, 318B, 318C, 319C, 320C, 320C FM, 320C L, 321C, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 933, 933C, 939, 939C, D3C III,...
0966027
SEAL-O-RING
307, 307B, 307C, 308C, E200B, E240C, E300B, EL240B
307, 307B, 307C, 308C, E200B, E240C, E300B, EL240B