1073120 SEAL-O-RING Caterpillar parts
320C, 330C, 330C FM, 330C L, 345B II, 345B II MH, 345C, 657G, 906H, 906H2, 907H, 907H2, 908H, 908H2, AP-1055D, AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG-2455D, BG-260D, BG1000E, BG1055E, BG500E, ...
Rating:
Alternative (cross code) number:
CA1073120
107-3120
1073120
CA1073120
107-3120
1073120
Weight: 0.01 pounds 0 kg.
Information:
CROSS SECTION DIAMETER
2.62
mm
DASH SIZE
155
ID
101.27
mm
MATERIAL
Fluorocarbon (FKM) Rubber - 90 Duro
OD
0
mm
ASPHALT PAVER, WHEELED EXCAVATOR,
Compatible equipment models: 1073120:
Number on catalog scheme:
12
For full view, you need register
Information:
Lip-type seals can cause a groove to wear in the part that they seal against. Many times this part could be used again except for the groove wear. New wear sleeves are now available to install over the groove, to give a new seal surface to the worn part. This will let the worn part be used again and allow the use of the original part number seal. This instruction gives the part numbers of the wear sleeves and sleeve drivers (installation tools) and the procedure needed to make the repair. A chart gives the part number of sleeve to install according to the size of the wear surface that is to have the repair. If a wear sleeve is to be installed on a 1P7718 or 2P4722 Water Pump Shaft Assembly, (for D353 Engines), see SPECIAL PROCEDURES on page 11.Wear Sleeves And Wear Sleeve Drivers
1 There is a specific wear sleeve driver to use for installation of each wear sleeve. The drivers are all either a type (A), (B) or (C) as shown above. As seen in the illustration, type (A) and type (C) drivers have a closed end (shown) and an open end (not shown). These two drivers can be used in only one way to install a wear sleeve. To use type (B) drivers (open on both ends), always put the end that has the rolled (round) part (R), next to the wear sleeve. 2 The illustration above shows a typical wear sleeve. The wear sleeve is made in one piece and has a wear surface (1) for the seal, and a flange (2). In most applications of the wear sleeve, it will be necessary to remove flange (2). Instructions for removal of flange (2) are given in WEAR SLEEVE INSTALLATION.Application Chart By Reference To Shaft Size
Application Chart By Reference To Part Number
Application Chart By Reference To Part Number (Con't.)
Application Chart By Reference To Part Number (Con't.)
Application Chart By Reference To Part Number (Con't.)
Wear Sleeve Installation
1 Carefully inspect the wear surface for the seal. Wear groove (A) shows typical wear by a lip-type seal. Clean the wear surface thoroughly. Use emery cloth (1) of 180 grit or finer to clean the wear surface. Use a file to make smooth any nicks or burrs (deep grooves or notches). 2 Hold wear sleeve (2) in the position shown, so the center of new wear surface (B) is over wear groove (A), then make a mark (C) that is even with the back of flange (D) of wear sleeve (2). If there is more than one wear groove, make sure that all wear grooves will be covered an even amount. If it is seen that flange (D) will be against a shoulder after it is installed, mark (C) is not needed; see step 5. 3 If groove (A) is a deep groove, fill it with a powdered metal epoxy and install the wear sleeve before the epoxy becomes hard. If the powdered metal epoxy is not needed,
1 There is a specific wear sleeve driver to use for installation of each wear sleeve. The drivers are all either a type (A), (B) or (C) as shown above. As seen in the illustration, type (A) and type (C) drivers have a closed end (shown) and an open end (not shown). These two drivers can be used in only one way to install a wear sleeve. To use type (B) drivers (open on both ends), always put the end that has the rolled (round) part (R), next to the wear sleeve. 2 The illustration above shows a typical wear sleeve. The wear sleeve is made in one piece and has a wear surface (1) for the seal, and a flange (2). In most applications of the wear sleeve, it will be necessary to remove flange (2). Instructions for removal of flange (2) are given in WEAR SLEEVE INSTALLATION.Application Chart By Reference To Shaft Size
Application Chart By Reference To Part Number
Application Chart By Reference To Part Number (Con't.)
Application Chart By Reference To Part Number (Con't.)
Application Chart By Reference To Part Number (Con't.)
Wear Sleeve Installation
1 Carefully inspect the wear surface for the seal. Wear groove (A) shows typical wear by a lip-type seal. Clean the wear surface thoroughly. Use emery cloth (1) of 180 grit or finer to clean the wear surface. Use a file to make smooth any nicks or burrs (deep grooves or notches). 2 Hold wear sleeve (2) in the position shown, so the center of new wear surface (B) is over wear groove (A), then make a mark (C) that is even with the back of flange (D) of wear sleeve (2). If there is more than one wear groove, make sure that all wear grooves will be covered an even amount. If it is seen that flange (D) will be against a shoulder after it is installed, mark (C) is not needed; see step 5. 3 If groove (A) is a deep groove, fill it with a powdered metal epoxy and install the wear sleeve before the epoxy becomes hard. If the powdered metal epoxy is not needed,
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
328D LCR, 330C L, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 345C MH, 345D L, 349D L, 349E, 349E ...
330C, 330D L, 330D MH, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L
330C, 330D L, 330D MH, 345B II, 345B II MH, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 374D L, 374F L
345B II, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
345B II, 345B L, 350, 365B, 365B II, 365B L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
345B II, 345C, 345D, 345D L, 349D, 349D L
345B II, 345C, 345D, 345D L, 349D, 349D L
330B, 330B L, 330C L, 330D, 330D L, 336D
631E, 631G, 633E II, 637E, 637G, AP-1000, AP-1000B, AP-1050, AP-650B, AP-655D, AP-800C, AP-800D, BG-225B, BG-225C, BG-245C, CB-434, CB-44B, CB-534B, CB-534C, CB-534D, CB-535B, CB-54, CB-54B, CB-564D, ...
3632112
SEAL-LIP TYPE
730C, CX31, CX31-C13I, CX31-C15I, CX31-C18I, CX31-P600, CX35, CX35-P800
730C, CX31, CX31-C13I, CX31-C15I, CX31-C18I, CX31-P600, CX35, CX35-P800
3503698
SEAL-RING
730C, CX31, CX31-P600
730C, CX31, CX31-P600
CX31, CX31-C13I, CX31-C15I, CX31-C18I, CX31-C9I, CX31-P600
2644802
SEAL AS-BALANCE
CX31, CX31-C9I, CX35
CX31, CX31-C9I, CX35
2680226
SEAL
730C, CX31, CX31-C13I, CX31-C15I, CX31-C18I, CX31-C9I, CX31-P600
730C, CX31, CX31-C13I, CX31-C15I, CX31-C18I, CX31-C9I, CX31-P600
CX31, CX31-P600, M313C, M313D, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318C, M318C MH, M318D, M318D MH, M322C, M322D, M322D MH, M325C MH, M325D L MH, M325D MH, M330D
2926378
SEAL-O-RING
CX31
CX31
5110B, 651E, 657G, 797, 834G, 834H, 836G, 836H, 844K, 854K, 924G, 924GZ, 924H, 924HZ, 928H, 928HZ, 930G, 963C, 973D, 988G, 988H, 990K, 992K, 993K, CX31, D8T, D9T, IT28G